04.11.2014 Views

Definity ECS Admin for Network Connectivity.pdf - TextFiles.com

Definity ECS Admin for Network Connectivity.pdf - TextFiles.com

Definity ECS Admin for Network Connectivity.pdf - TextFiles.com

SHOW MORE
SHOW LESS

You also want an ePaper? Increase the reach of your titles

YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.

<strong>Network</strong>ing Screens<br />

A Screens Reference<br />

Metric<br />

The metric value indicates the desirability of the IP route in terms of the efficiency of<br />

the data transmission between two nodes.<br />

Valid Values Usage<br />

0 or 1 A metric value of 1 is used only on a switch that has more than<br />

one C-LAN board installed.<br />

You can always enter either 0 or 1 in the Metric field but the<br />

choice should be guided by the in<strong>for</strong>mation below.<br />

If there are two routes to the same destination, one with metric 0 and one with metric<br />

1, the switch software will choose the route with metric 0 because it is (if properly<br />

administered) the more efficient route of the two. On the other hand, if both routes are<br />

administered with metric 0, the switch will choose whichever it sees first, not<br />

necessarily the most efficient one.<br />

By entering 1 in the Metric field, you are telling the switch, “this is a <strong>com</strong>plex route;<br />

if you know of a simpler route (metric 0) to this destination, use that instead.” In other<br />

words, metric 1 diverts usage of the route to a metric-0 route, if available.<br />

The following diagram illustrates the use of the Metric field. Switches A and C are<br />

connected via switch B over two LANs. Switch B has two C-LAN boards, which are<br />

connected via a ppp link. The network nodes are numbered 1 through 6.<br />

LAN<br />

ethernet<br />

1<br />

C-LANa<br />

2<br />

C-LAN1<br />

3<br />

ppp<br />

4<br />

C-LAN2<br />

Switch B<br />

5<br />

LAN<br />

ethernet<br />

6<br />

C-LANc<br />

Switch A<br />

Switch C<br />

The following IP routes are required <strong>for</strong> <strong>com</strong>munications between switches A and C:<br />

<strong>Admin</strong>istered Destination Gateway<br />

Route on Board Loc. Node Node Metric<br />

1 Switch A C-LANa 6 2 0<br />

2 Switch B C-LAN1 6 4 1<br />

3 Switch B C-LAN2 1 3 1<br />

4 Switch C C-LANc 1 5 0<br />

Implied Switch B C-LAN2 6 5 0<br />

The implied route from C-LAN2 to node 6 via node 5 is not administered on the IP<br />

Routing screen but is a built-in part of the C-LAN firmware and the automatic subnet<br />

routing feature. (We are assuming that automatic subnet routing is enabled <strong>for</strong> node 5<br />

on the Data Module screen.) There<strong>for</strong>e, on Switch B there are two routes to<br />

destination 6 — route 2 and the implied route.<br />

<strong>Admin</strong>istration <strong>for</strong> <strong>Network</strong> <strong>Connectivity</strong><br />

555-233-504 — Issue 1 — April 2000 CID: 77730<br />

253

Hooray! Your file is uploaded and ready to be published.

Saved successfully!

Ooh no, something went wrong!