EvitaXL

More documents

Recommendations

Info

Sensors Zero/check/calibrate CO2 sensor ● Touch the screen knob. ● Enter the concentration = turn rotary knob, confirm = press rotary knob. When using the standard calibration gas (5 Vol.% CO2 and 95 Vol.% N2): ● Set O2 concentration to »0«, CO2 concentration to »5«. ● Touch the »Start« screen key. During calibration, the following message is displayed on the screen: CO2 calibration. Please wait EvitaXL carries out calibration and confirms with the message: CO2 calibration ok Failed calibration is indicated by the ventilator with the message: CO2 calibration interrupted or CO2 calibration not ok ● Repeat the calibration of the CO2 sensor. If calibration still proves impossible, the CO2 concentration value entered may not be the same as that in the cylinder: ● Check CO2 value entered, or calibration gas cylinder is empty: ● Use a new calibration gas cylinder or sensor is defective: ● Replace sensor. 116 Instructions for Use EvitaXL 140
Resetting CO2 calibration — If calibration was not successful or if there were problems during calibration, the sensor can be reset to the factory reset values. In the menu »CO2«: ● Touch the screen key »Calibration«. ● Touch the screen key »Reset Cal.«. The calibration is reset by EvitaXL after approx. 5 seconds and the factory-set calibration value is now effective again. ● Recover the correct calibration as soon as possible! Sensors Zero/check/calibrate CO2 sensor Instructions for Use EvitaXL 117 140
Page 1 and 2:
EvitaXL Intensive Care Ventilator S
Page 3 and 4:
Contents Contents For Your Safety a
Page 5 and 6:
For Your Safety and that of Your Pa
Page 7 and 8:
Intended Medical Application Intend
Page 9 and 10:
Lung Protection Package (optional)
Page 11 and 12:
Operating concept Operating concept
Page 13 and 14:
The screen... displays all the most
Page 15 and 16:
To set the ventilation mode and ven
Page 17 and 18:
To set ventilation parameters direc
Page 19 and 20:
PressureLink* Linked adjustment of
Page 21 and 22:
Preparing for use Preparing for use
Page 23 and 24:
1 lock it in position = pull tab un
Page 25 and 26:
Using HME, bacterial filters and ho
Page 27 and 28:
1 Hang the hinged arm from the rail
Page 29 and 30:
Fitting CO2 cuvette and CO2 sensor
Page 31 and 32:
Gas supply ● Screw the connecting
Page 33 and 34:
Connecting the nurse call (optional
Page 35 and 36:
Preparing the child test lung 84 09
Page 37 and 38:
● Touch the screen key »Check«.
Page 39 and 40:
Leak test This test must be perform
Page 41 and 42:
Ventilation while transferring a pa
Page 43 and 44:
Operation Starting up . . . . . . .
Page 45 and 46:
Starting up Switching on ● Switch
Page 47 and 48:
Setting new ventilation parameters
Page 49 and 50:
IPPV Intermittent Positive Pressure
Page 51 and 52:
To view additional text information
Page 53 and 54:
ILV ILV = Independent Lung Ventilat
Page 55 and 56:
Setting the Master and Slave device
Page 57 and 58:
ILV: Master and Slave Synchronisati
Page 59 and 60:
BIPAP, BIPAP/ASB Biphasic Positive
Page 61 and 62:
BIPAPAssist Biphasic Positive Airwa
Page 63 and 64:
CPAP-ASB Continuous Positive Airway
Page 65 and 66: No initial values for PPS To protec
Page 67 and 68: To review, activate or set: In the
Page 69 and 70: Apnoea Ventilation For automatic sw
Page 71 and 72: AutoFlow for automatic regulation o
Page 73 and 74: -----------------------------------
Page 75 and 76: PLV* Pressure Limited Ventilation S
Page 77 and 78: Selecting application mode »Mask«
Page 79 and 80: Setting alarm limits ● Press key
Page 81 and 82: Remedy the fault ● Refer to the l
Page 83 and 84: Displaying graphics The following r
Page 85 and 86: Freeze To freeze the current real-t
Page 87 and 88: Display 1 hr trend ● Touch the fu
Page 89 and 90: Display logbook Changes, events and
Page 91 and 92: Additional functions Medicament neb
Page 93 and 94: Switch on the medicament nebuliser:
Page 95 and 96: EvitaXL ventilates the patient in t
Page 97 and 98: Expiration Hold This function may b
Page 99 and 100: Set the interval ● Touch the scre
Page 101 and 102: Negative Inspiratory Force NIF The
Page 103 and 104: Measuring procedure ● Touch the s
Page 105 and 106: Measurement analysis After the meas
Page 107 and 108: ● Press the key » Sensor Paramet
Page 109 and 110: O2 sensor calibration — After rep
Page 111 and 112: CO2 zero calibration Only possible
Page 113 and 114: ● Place the test filter in the CO
Page 115: Calibrating the CO2 sensor — If t
Page 119 and 120: Selecting Standby Mode — To perfo
Page 121 and 122: O2 Therapy (optional) During the O2
Page 123 and 124: Switching on O2 Therapy ● Touch t
Page 125 and 126: Configuration Configuration . . . .
Page 127 and 128: Day/night function for screen brigh
Page 129 and 130: Define the trends to be recorded
Page 131 and 132: Define customised values and settin
Page 133 and 134: Lock the screen configuration again
Page 135 and 136: Select units Specific national unit
Page 137 and 138: Specific initial therapy values ●
Page 139 and 140: Set initial values for VT and f…
Page 141 and 142: Define start-up values for special
Page 143 and 144: Fault — Cause — Remedy Fault -
Page 145 and 146: Message Cause Remedy Apnoea !!! Pat
Page 147 and 148: Message Cause Remedy Exp. hold inte
Page 149 and 150: Message Cause Remedy Leakage Not di
Page 151 and 152: Message Cause Remedy Fault - Cause
Page 153 and 154: Message Cause Remedy Tidal volume h
Page 155 and 156: Preparing Preparing . . . . . . . .
Page 157 and 158: Medicament nebuliser (optional) 1 R
Page 159 and 160: The expiration valve is only disman
Page 161 and 162: As for ventilation hoses, water tra
Page 163 and 164: Assembling Mounting the expiration
Page 165 and 166: Maintenance/Disposal Maintenance/Di
Page 167 and 168:
Replace cooling air filter — Clea
Page 169 and 170:
Mains power/DC power operation Main
Page 171 and 172:
Use of the power supplies Operation
Page 173 and 174:
Connecting an external battery Note
Page 175 and 176:
Operation with mains power The vent
Page 177 and 178:
Evita 4 Link (optional) Evita 4 Lin
Page 179 and 180:
Preparation The interface board may
Page 181 and 182:
Select printer protocol ● See "Se
Page 183 and 184:
What's what What's what . . . . . .
Page 185 and 186:
Front connections 1 » « Gas outle
Page 187 and 188:
Technical Data Technical Data . . .
Page 189 and 190:
APRV Airway Pressure Release Ventil
Page 191 and 192:
Performance characteristics Control
Page 193 and 194:
Frequency Measurement Breathing fre
Page 195 and 196:
Monitoring Expiratory minute volume
Page 197 and 198:
Materials used Part Appearance Mate
Page 199 and 200:
Technical Data Equipment outputs An
Page 201 and 202:
LUST protocol LUST: List-controlled
Page 203 and 204:
End of telegram "EOT" Status telegr
Page 205 and 206:
23 FiO2 high 24 FiO2 low 25 MV low
Page 207 and 208:
Description Ventilation Modes . . .
Page 209 and 210:
AutoFlow ® The AutoFlow function c
Page 211 and 212:
SIMV Synchronised Intermittent Mand
Page 213 and 214:
Response times longer than 15 secon
Page 215 and 216:
BIPAPAssist Biphasic Positive Airwa
Page 217 and 218:
PPS (optional) In ventilation mode
Page 219 and 220:
The difference between measured val
Page 221 and 222:
Unlimited volume compensation is in
Page 223 and 224:
Tube type Inside diameter of tube (
Page 225 and 226:
Rapid-Shallow-Breathing RSB The Rap
Page 227 and 228:
Low Flow PV-Loop The Low Flow PV-Lo
Page 229 and 230:
Screen configurations Screen config
Page 231 and 232:
Screen configurations Screen config
Page 233 and 234:
Abreviation Explanation P 0.1 100 m
Page 235 and 236:
Bibliography [1] Baum, M., Benzer,
Page 237 and 238:
Special ASCII characters used Chara
Page 239 and 240:
Instructions for Use EvitaXL 239
Page 241 and 242:
For paediatric ventilation Item No.
Page 243 and 244:
Name/Description Order No. For CO2
Page 245 and 246:
New features in EvitaXL SW 6.n Indi
Page 247 and 248:
Index A Abbreviations . . . . . . .
Page 249 and 250:
Performance characteristics . . . .
show all

EvitaXL

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?