EvitaXL

More documents

Recommendations

Info

Setting alarm limits Suppress alarm tone Power failure alarm Suppress alarm tone for max. 2 minutes: 1 Press key »g Alarm Silence«, its yellow LED lights up. The acoustic alarm is suppressed for two minutes. 2 The remaining time is displayed on the screen. If the fault triggering the alarm has not been remedied after 2 minutes, the acoustic alarm sounds again. If the acoustic alarm is to be re-activated prematurely: 1 Press key »g Alarm Silence« again, its LED goes out. Acknowledge: See "Fault – Cause – Remedy", page 143, for alarms which can be reset via the Alarm Reset key. ● Touch the screen key »Alarm Reset«, confirm = press rotary knob. Power failure alarm If the loudspeaker for acoustic alarm signalling fails on account of a defect, a continuous tone will be generated by an auxiliary alarm. This continuous tone also draws attention to a power failure (see page 30, in the event of an interruption in the power supply). ➁ D 82 Instructions for Use EvitaXL EvitaXL 1 032 214
Displaying graphics The following real-time curves can be displayed: — PAW (t) — Flow (t) — Volume (t) — etCO2 (t) (optional) — Pleth (optional) — a real-time curve combined with a short trend or a Recruitment Trend (breath-based trend) (optional). ● Touch the function key » ? Main«. To select other real-time curves: ● Touch the relevant screen key » « and EvitaXL opens the menu »Curves«. ● Touch the screen key »Curve only«. ● Touch the screen key for the required parameter of the real-time curve. ● The EvitaXL displays the real-time curve of the parameter. The menu disappears automatically. ● To freeze real-time curves, see "Freeze" on page 85. To display the real-time curve in combination with a short trend: In the menu »Curves« ● Touch the screen key »Curve + Shorttrend«. The required real-time curve can be combined with the short trend for any chosen parameter. The relevant real-time curve is displayed in the menu and the screen key of the corresponding short-trend parameter appears in dark green. ● Touch the screen key of the required parameter for the corresponding short trend. Displaying graphics Instructions for Use EvitaXL 83 120
Page 1 and 2:
EvitaXL Intensive Care Ventilator S
Page 3 and 4:
Contents Contents For Your Safety a
Page 5 and 6:
For Your Safety and that of Your Pa
Page 7 and 8:
Intended Medical Application Intend
Page 9 and 10:
Lung Protection Package (optional)
Page 11 and 12:
Operating concept Operating concept
Page 13 and 14:
The screen... displays all the most
Page 15 and 16:
To set the ventilation mode and ven
Page 17 and 18:
To set ventilation parameters direc
Page 19 and 20:
PressureLink* Linked adjustment of
Page 21 and 22:
Preparing for use Preparing for use
Page 23 and 24:
1 lock it in position = pull tab un
Page 25 and 26:
Using HME, bacterial filters and ho
Page 27 and 28:
1 Hang the hinged arm from the rail
Page 29 and 30:
Fitting CO2 cuvette and CO2 sensor
Page 31 and 32: Gas supply ● Screw the connecting
Page 33 and 34: Connecting the nurse call (optional
Page 35 and 36: Preparing the child test lung 84 09
Page 37 and 38: ● Touch the screen key »Check«.
Page 39 and 40: Leak test This test must be perform
Page 41 and 42: Ventilation while transferring a pa
Page 43 and 44: Operation Starting up . . . . . . .
Page 45 and 46: Starting up Switching on ● Switch
Page 47 and 48: Setting new ventilation parameters
Page 49 and 50: IPPV Intermittent Positive Pressure
Page 51 and 52: To view additional text information
Page 53 and 54: ILV ILV = Independent Lung Ventilat
Page 55 and 56: Setting the Master and Slave device
Page 57 and 58: ILV: Master and Slave Synchronisati
Page 59 and 60: BIPAP, BIPAP/ASB Biphasic Positive
Page 61 and 62: BIPAPAssist Biphasic Positive Airwa
Page 63 and 64: CPAP-ASB Continuous Positive Airway
Page 65 and 66: No initial values for PPS To protec
Page 67 and 68: To review, activate or set: In the
Page 69 and 70: Apnoea Ventilation For automatic sw
Page 71 and 72: AutoFlow for automatic regulation o
Page 73 and 74: -----------------------------------
Page 75 and 76: PLV* Pressure Limited Ventilation S
Page 77 and 78: Selecting application mode »Mask«
Page 79 and 80: Setting alarm limits ● Press key
Page 81: Remedy the fault ● Refer to the l
Page 85 and 86: Freeze To freeze the current real-t
Page 87 and 88: Display 1 hr trend ● Touch the fu
Page 89 and 90: Display logbook Changes, events and
Page 91 and 92: Additional functions Medicament neb
Page 93 and 94: Switch on the medicament nebuliser:
Page 95 and 96: EvitaXL ventilates the patient in t
Page 97 and 98: Expiration Hold This function may b
Page 99 and 100: Set the interval ● Touch the scre
Page 101 and 102: Negative Inspiratory Force NIF The
Page 103 and 104: Measuring procedure ● Touch the s
Page 105 and 106: Measurement analysis After the meas
Page 107 and 108: ● Press the key » Sensor Paramet
Page 109 and 110: O2 sensor calibration — After rep
Page 111 and 112: CO2 zero calibration Only possible
Page 113 and 114: ● Place the test filter in the CO
Page 115 and 116: Calibrating the CO2 sensor — If t
Page 117 and 118: Resetting CO2 calibration — If ca
Page 119 and 120: Selecting Standby Mode — To perfo
Page 121 and 122: O2 Therapy (optional) During the O2
Page 123 and 124: Switching on O2 Therapy ● Touch t
Page 125 and 126: Configuration Configuration . . . .
Page 127 and 128: Day/night function for screen brigh
Page 129 and 130: Define the trends to be recorded
Page 131 and 132: Define customised values and settin
Page 133 and 134:
Lock the screen configuration again
Page 135 and 136:
Select units Specific national unit
Page 137 and 138:
Specific initial therapy values ●
Page 139 and 140:
Set initial values for VT and f…
Page 141 and 142:
Define start-up values for special
Page 143 and 144:
Fault — Cause — Remedy Fault -
Page 145 and 146:
Message Cause Remedy Apnoea !!! Pat
Page 147 and 148:
Message Cause Remedy Exp. hold inte
Page 149 and 150:
Message Cause Remedy Leakage Not di
Page 151 and 152:
Message Cause Remedy Fault - Cause
Page 153 and 154:
Message Cause Remedy Tidal volume h
Page 155 and 156:
Preparing Preparing . . . . . . . .
Page 157 and 158:
Medicament nebuliser (optional) 1 R
Page 159 and 160:
The expiration valve is only disman
Page 161 and 162:
As for ventilation hoses, water tra
Page 163 and 164:
Assembling Mounting the expiration
Page 165 and 166:
Maintenance/Disposal Maintenance/Di
Page 167 and 168:
Replace cooling air filter — Clea
Page 169 and 170:
Mains power/DC power operation Main
Page 171 and 172:
Use of the power supplies Operation
Page 173 and 174:
Connecting an external battery Note
Page 175 and 176:
Operation with mains power The vent
Page 177 and 178:
Evita 4 Link (optional) Evita 4 Lin
Page 179 and 180:
Preparation The interface board may
Page 181 and 182:
Select printer protocol ● See "Se
Page 183 and 184:
What's what What's what . . . . . .
Page 185 and 186:
Front connections 1 » « Gas outle
Page 187 and 188:
Technical Data Technical Data . . .
Page 189 and 190:
APRV Airway Pressure Release Ventil
Page 191 and 192:
Performance characteristics Control
Page 193 and 194:
Frequency Measurement Breathing fre
Page 195 and 196:
Monitoring Expiratory minute volume
Page 197 and 198:
Materials used Part Appearance Mate
Page 199 and 200:
Technical Data Equipment outputs An
Page 201 and 202:
LUST protocol LUST: List-controlled
Page 203 and 204:
End of telegram "EOT" Status telegr
Page 205 and 206:
23 FiO2 high 24 FiO2 low 25 MV low
Page 207 and 208:
Description Ventilation Modes . . .
Page 209 and 210:
AutoFlow ® The AutoFlow function c
Page 211 and 212:
SIMV Synchronised Intermittent Mand
Page 213 and 214:
Response times longer than 15 secon
Page 215 and 216:
BIPAPAssist Biphasic Positive Airwa
Page 217 and 218:
PPS (optional) In ventilation mode
Page 219 and 220:
The difference between measured val
Page 221 and 222:
Unlimited volume compensation is in
Page 223 and 224:
Tube type Inside diameter of tube (
Page 225 and 226:
Rapid-Shallow-Breathing RSB The Rap
Page 227 and 228:
Low Flow PV-Loop The Low Flow PV-Lo
Page 229 and 230:
Screen configurations Screen config
Page 231 and 232:
Screen configurations Screen config
Page 233 and 234:
Abreviation Explanation P 0.1 100 m
Page 235 and 236:
Bibliography [1] Baum, M., Benzer,
Page 237 and 238:
Special ASCII characters used Chara
Page 239 and 240:
Instructions for Use EvitaXL 239
Page 241 and 242:
For paediatric ventilation Item No.
Page 243 and 244:
Name/Description Order No. For CO2
Page 245 and 246:
New features in EvitaXL SW 6.n Indi
Page 247 and 248:
Index A Abbreviations . . . . . . .
Page 249 and 250:
Performance characteristics . . . .
show all

EvitaXL

Create successful ePaper yourself

Delete template?

Save as template?