Extron XTP CrossPoint 1600 and 3200 ... - Extron Electronics
Extron XTP CrossPoint 1600 and 3200 ... - Extron Electronics
Extron XTP CrossPoint 1600 and 3200 ... - Extron Electronics
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
SIS Comm<strong>and</strong> <strong>and</strong> Response Table for Output-Board-Specific Comm<strong>and</strong>s<br />
Comm<strong>and</strong> Function<br />
The table that starts below shows comm<strong>and</strong>s that affect outputs only <strong>and</strong>, in general, apply<br />
to installed output boards. Where a comm<strong>and</strong> does not apply to all output board types, the<br />
valid board types are noted.<br />
SIS Comm<strong>and</strong><br />
(Host to Unit)<br />
Response<br />
(Unit to Host)<br />
Outputs on <strong>XTP</strong> CP 4o HDMI <strong>and</strong> <strong>XTP</strong> CP 4o DVI Pro Boards<br />
Audio routing selections<br />
Additional description<br />
NOTE: These comm<strong>and</strong>s select between the audio embedded in the digital video stream <strong>and</strong> the 2-channel analog audio.<br />
Output audio HDMI select E O X@ * X3# AFMT } AfmtOX@ * X3#] When audio is broken away from video,<br />
embed audio from the X3# source in the<br />
video output.<br />
Example: E O3*0AFMT } AfmtO03*0] When audio is broken away from video,<br />
use the embedded audio from the input<br />
port when creating an audio breakaway<br />
tie to output 3.<br />
View output audio breakaway E O X@ AFMT }<br />
X3#]<br />
selection<br />
View output audio breakaway<br />
selection, all outputs<br />
E OAFMT } X3# 1 X3# 2 X3# 3 ... X3# n ] 16 or 32 ( n ) sequential audio output<br />
selections, starting from output 1.<br />
Enable black signal output for audio<br />
only tie<br />
E B X@ *1AFMT } AfmtBX@ *1 ] Enable black signal in audio only tie to<br />
output X@.<br />
Disable black signal output for audio<br />
only tie<br />
E B X@ *0AFMT } AfmtBX@ *0 ] Disable black signal in audio only tie to<br />
output X@.<br />
View black signal output status E B X@ AFMT } X2#] The black signal status of output X@ is X2#.<br />
Enable black signal for all audio<br />
only ties<br />
E B1*AFMT } AfmtB1] Enable black signal in audio only tie to<br />
all outputs.<br />
Disable black signal for all audio<br />
only ties<br />
E B0*AFMT } AfmtB0] Disable black signal in audio only tie to<br />
all outputs.<br />
HDCP status<br />
View output HDCP status E O X@ HDCP } X3$]<br />
View HDCP status of all outputs E O*HDCP } X3$ 1 X3$ 2 X3$ 3 ... X3$ n ]<br />
Video mutes<br />
Video mute X@ *1B Vmt X@ *1 ] Mute output X@ video (video off).<br />
Video unmute X@ *0B Vmt X@ *0 ] Unmute output X@ video (video on).<br />
Read video mute X@ B X2#] X2# = 1 = enable (muted)<br />
0 = disable (unmuted) (default).<br />
Global video mute 1*B Vmt1] Mute all video outputs.<br />
Global video unmute 0*B Vmt0] Unmute all video outputs.<br />
NOTE: X@ = Output number 01 – 16 or 32<br />
X2# = Enable, disable (for black video <strong>and</strong> mutes, see above) 0 = Disable 1 = Enable<br />
X3# = Output audio source 0 = Original HDMI audio 1 = Embed audio<br />
X3$ = HDCP status (for outputs) 0, 2, 4, or 6 = No monitor connected<br />
1, 3, or 5 = Monitor connected but the video signal is not encrypted<br />
7 = Monitor connected <strong>and</strong> the video signal is encrypted<br />
<strong>XTP</strong> <strong>CrossPoint</strong> <strong>1600</strong> <strong>and</strong> <strong>3200</strong> Switchers • Programming Guide 95