Extron XTP CrossPoint 1600 and 3200 ... - Extron Electronics

SIS Command and Response Table for Input-Board-Specific Commands (continued)
Command Function
SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional description
Inputs on XTP CP 4i HDMI and XTP CP 4i DVI Pro Boards (continued)
HDCP status
View input HDCP status E I X^HDCP } X1$]
View HDCP status of all inputs E I*HDCP } X1$ 1 X1$ 2 X1$ 3 ... X1$ n ]
Inputs on XTP CP 4i [XTP] Boards
Captive screw and Ethernet serial port insertion enables
Enable an input captive screw serial
port insertion
E I X^*0LRPT } LrptIX^*0 ] Enable the captive screw serial port
insert on input X^. This disables the
Ethernet RS-232 insert.
Enable an input Ethernet serial port
insertion
E I X^*1LRPT } LrptIX^*1 ] Enable the Ethernet serial port insert
on input X^. This disables the captive
screw serial port insert.
Set all RS-232 input insertions E I* X1% *LRPT } LrptI00*X1%]
View input insertion E I X^LRPT } X1%]
View all input insertions E ILRPT } X1% 1 X1% 2 X1% 3 ... X1% n ] One X1% for each available (installed)
input, starting at input 1. Inputs that are
not on an XTP CP 4i [XTP] board report
as 0.
Ethernet serial port insert parameters
Set serial port parameters EX1^*X1& , X1* , X1( , X2) CP }
CpnX1^•Ccp X1& , X1* , X1( , X2)]
Read serial port parameters EX1^CP } X1&,X1*,X1(,X2)]
Configure current port timeout E 0* X2! TC } Pti0*X2!]
Read current port timeout E 0TC } X2!]
Configure global IP port timeout E 1* X2! TC } Pti1*X2!]
Read global IP port timeout E 1TC } X2!]
Set UART start point EX2@ MD } PmdX2@] Sets the initial (lowest) port number for
the range of numbers assigned to the
serial port and UARTs.
Read UART start point E MD } X2@]
NOTE: X^ = Input number (for other than tie) 01 – 16 or 32
X1$ = HDCP status (for inputs) 0 = No source device connected
1 = Source connected is HDCP-compliant
2 = Source connected is not HDCP-compliant
X1% = Captive screw or UART 0 = Captive screw RS-232 insert (default) 1 = Ethernet RS-232 insert (UART)
X1^ = Port number 03 — 34 = UARTs (inputs) 1 — 32
X1& = Baud rate 9600 (default), 19200, 38400, 115200
X1* = Parity odd, even, none, mark, space (only the first letter is required)
X1( = Data bits 7, 8 (default)
X2) = Stop bits 1 (default), 2
X2! = Port timeout (10-sec. increments) 1 (= 10 seconds) - 65000 (default is 30 = 300 seconds = 5 minutes)
X2@ = UART starting point
The starting point (X2@) is the rear panel RS-232/RS-422 port.
The next position (X2@ +1 ) is not used.
For the XTP CrossPoint 1600, X2@ +2 through X2@ +18 are XTP inputs.
For the XTP CrossPoint 3200, X2@ +2 through X2@ +34 are XTP inputs.
Default values: 1999 = Rear panel remote RS-232/RS-422 port
2000 is unused
2001 through 2016 (XTP CrossPoint 1600) = Input 1 through 16
2001 through 2032 (XTP CrossPoint 3200) = Input 1 through 32
XTP CrossPoint 1600 and 3200 Switchers • Programming Guide 84