- Page 1 and 2:
User Guide Matrix Switchers XTP Cro
- Page 3 and 4:
Conventions Used in this Guide Noti
- Page 5 and 6:
Contents Introduction..............
- Page 7 and 8:
IR STANDBY/ON CONFIG CHANNEL SDTV E
- Page 9 and 10:
The matrix switchers can be remotel
- Page 11 and 12:
HDMI and DVI Pro input and output b
- Page 13 and 14:
HDMI 1.3 compatible — Supports HD
- Page 15 and 16:
Installation This sections details
- Page 17 and 18:
LAN RS 232/RS422 1 2 REMOTE 3 4 ACT
- Page 19 and 20:
1d IR/RS-232 Over XTP Connectors
- Page 21 and 22:
XTP CP 4o HDMI (HDMI Output board)
- Page 23 and 24:
XTP board XTP ports — The XTP inp
- Page 25 and 26:
Use the LockIt Lacing Brackets, sup
- Page 27 and 28:
The level for each analog audio inp
- Page 29 and 30:
Front Panel Configuration Port and
- Page 31 and 32:
XTP CROSSPOINT 3200 1 2 INPUTS 1 2
- Page 33 and 34:
Control Buttons Primary functions N
- Page 35 and 36:
I/O Controls NOTE: See Front Panel
- Page 37 and 38:
Definitions The following Extron ma
- Page 39 and 40:
Example 1: Create a set of video an
- Page 41 and 42:
The current configuration (see figu
- Page 43 and 44:
Viewing the Configuration The curre
- Page 45 and 46:
5. Deselect video: Press and releas
- Page 47 and 48:
Example 5: Saving a preset In the f
- Page 49 and 50:
Muting and Unmuting Video and Audio
- Page 51 and 52:
INPUTS OUTPUTS CONFIG PRIMARY 1 2 R
- Page 53 and 54:
Table 4. XTP CrossPoint 3200 Audio
- Page 55 and 56:
Example 8: Viewing and adjusting an
- Page 57 and 58:
Viewing and Adjusting the Analog Ou
- Page 59 and 60:
Table 6. Audio Volume Display Highe
- Page 61 and 62:
4. Change the volume: Press and rel
- Page 63 and 64:
Selecting Lock mode 2 or toggling b
- Page 65 and 66:
3. Change a value: Press and releas
- Page 67 and 68:
Performing a Hard Reset (Reset 1) T
- Page 69 and 70:
Optimizing the Analog Audio Trouble
- Page 71 and 72:
Worksheet Example 2: Daily Configur
- Page 73 and 74:
XTP CrossPoint 3200 Switchers Confi
- Page 75 and 76:
Programming Guide The XTP CrossPoin
- Page 77 and 78:
Establishing a Connection Establish
- Page 79 and 80:
Outnn•Volxx] The switcher initiat
- Page 81 and 82:
Table 8. SIS Command vs. Switcher o
- Page 83 and 84:
Symbol definitions ] = Carriage ret
- Page 85 and 86:
SIS Command and Response Table for
- Page 87 and 88:
Table 10. EDID Values X$ Source or
- Page 89 and 90:
SIS Command and Response Table for
- Page 91 and 92:
SIS Command and Response Table for
- Page 93 and 94: SIS Command and Response Table for
- Page 95 and 96: SIS Command and Response Table for
- Page 97 and 98: SIS Command and Response Table for
- Page 99 and 100: SIS Command and Response Table for
- Page 101 and 102: SIS Command and Response Table for
- Page 103 and 104: SIS Command and Response Table for
- Page 105 and 106: SIS Command and Response Table for
- Page 107 and 108: SIS Command and Response Table for
- Page 109 and 110: SIS Command and Response Table for
- Page 111 and 112: SIS Command and Response Table for
- Page 113 and 114: SIS Command and Response Table for
- Page 115 and 116: X7( = Port number 01 = Remote RS-23
- Page 117 and 118: HTML Operation The XTP CrossPoint M
- Page 119 and 120: Status Tab System Status Page The S
- Page 121 and 122: HDCP Page The HDCP page (see figure
- Page 123 and 124: Unit Name field The Unit Name field
- Page 125 and 126: Passwords Page Access the Passwords
- Page 127 and 128: Setting up SMTP authorization If de
- Page 129 and 130: 2. Click the Firmware link. 3. Sele
- Page 131 and 132: File Management Tab File Management
- Page 133 and 134: NOTES: • If you lose track of the
- Page 135 and 136: Output Adjustments Page The Output
- Page 137 and 138: Muting and unmuting an audio output
- Page 139 and 140: Global Presets Page You can save an
- Page 141 and 142: ACT LAN LINK RESET 50-60Hz -A MAX I
- Page 143: Using the Button-Label Generator so
- Page 147 and 148: Pinging to Determine the Extron IP
- Page 149 and 150: 6. After verifying that the IP addr
- Page 151 and 152: Help For Telnet command definitions
- Page 153: Extron Warranty Extron Electronics