Extron XTP CrossPoint 1600 and 3200 ... - Extron Electronics

More documents

Recommendations

Info

Performing Soft System Resets (Resets 3, 4, and 5) Perform a soft reset of the switcher as follows: 1. Use a small screwdriver to press and hold the rear panel Reset button until the Reset LED and the front panel Video and Audio buttons blink the number of times for the desired reset: once (events reset), twice (system reset), or three times (absolute reset) (see figure 44). Press and hold the Reset button. Reset LED flashes once. RESET RESET Events Reset 3 seconds (Mode 3) Release, then immediately press and release again. RESET Front panel I/O buttons flash once. I / O VIDEO AUDIO Press and hold the Reset button. Reset LED flashes twice. Release, then immediately press and release again. IP Settings Reset (Mode 4) RESET 6 seconds RESET RESET Front panel I/O buttons flash twice. I / O VIDEO AUDIO Absolute Reset (Mode 5) Press and hold the Reset button. RESET 9 seconds Reset LED flashes three times. RESET Release, then immediately press and release again. RESET Front panel I/O buttons flash three times. I / O VIDEO AUDIO Figure 44. Soft System Resets 2. Release the Reset button and then immediately press and release the Reset button again. Nothing happens if the second momentary press does not occur within 1 second. XTP CrossPoint 1600 and 3200 Switchers • Operation 62
Optimizing the Analog Audio Troubleshooting The level for each analog audio input can be adjusted within a range of -18 dB to +24 dB, so there are no noticeable volume differences between sources and for the best headroom and signal-to-noise ratio. The volume for each analog audio output can be adjusted from full loudness to effectively muted. Adjust the levels as follows: 1. Connect analog audio sources to all desired inputs and connect the analog audio outputs to output devices such as audio players (see Input and Output Boards on page 12). For best results, wire all of the inputs and the outputs balanced. 2. Power on the audio sources, the switcher, and the audio players. 3. Switch among the inputs (see Creating a Configuration on page 32), listening to the audio with a critical ear or measuring the output audio level with test equipment, such as a VU meter. 4. As necessary, adjust the input audio level of each input (see Viewing and Adjusting the Input Audio Level on page 45) so that the approximate output level is the same for all selected inputs. 5. Tie an audio input to each analog audio output. 6. As necessary, adjust the output audio level of each output (see Viewing and Adjusting the Analog Output Volume on page 51). This section recommends what to do if you have problems operating the switcher. 1. Ensure that all devices are plugged in and powered on. 2. Check to see if one or more outputs are muted. 3. Ensure an active input is selected for output on the switcher. 4. Ensure that the proper signal format is supplied. 5. Check the cabling and make corrections as necessary. 6. Call the Extron S3 Sales and Technical Support Hotline if necessary. See the end of this guide for the phone number in your region of the world. XTP CrossPoint 1600 and 3200 Switchers • Operation 63
Page 1 and 2:
User Guide Matrix Switchers XTP Cro
Page 3 and 4:
Conventions Used in this Guide Noti
Page 5 and 6:
Contents Introduction..............
Page 7 and 8:
IR STANDBY/ON CONFIG CHANNEL SDTV E
Page 9 and 10:
The matrix switchers can be remotel
Page 11 and 12:
HDMI and DVI Pro input and output b
Page 13 and 14:
HDMI 1.3 compatible — Supports HD
Page 15 and 16:
Installation This sections details
Page 17 and 18: LAN RS 232/RS422 1 2 REMOTE 3 4 ACT
Page 19 and 20: 1d IR/RS-232 Over XTP Connectors
Page 21 and 22: XTP CP 4o HDMI (HDMI Output board)
Page 23 and 24: XTP board XTP ports — The XTP inp
Page 25 and 26: Use the LockIt Lacing Brackets, sup
Page 27 and 28: The level for each analog audio inp
Page 29 and 30: Front Panel Configuration Port and
Page 31 and 32: XTP CROSSPOINT 3200 1 2 INPUTS 1 2
Page 33 and 34: Control Buttons Primary functions N
Page 35 and 36: I/O Controls NOTE: See Front Panel
Page 37 and 38: Definitions The following Extron ma
Page 39 and 40: Example 1: Create a set of video an
Page 41 and 42: The current configuration (see figu
Page 43 and 44: Viewing the Configuration The curre
Page 45 and 46: 5. Deselect video: Press and releas
Page 47 and 48: Example 5: Saving a preset In the f
Page 49 and 50: Muting and Unmuting Video and Audio
Page 51 and 52: INPUTS OUTPUTS CONFIG PRIMARY 1 2 R
Page 53 and 54: Table 4. XTP CrossPoint 3200 Audio
Page 55 and 56: Example 8: Viewing and adjusting an
Page 57 and 58: Viewing and Adjusting the Analog Ou
Page 59 and 60: Table 6. Audio Volume Display Highe
Page 61 and 62: 4. Change the volume: Press and rel
Page 63 and 64: Selecting Lock mode 2 or toggling b
Page 65 and 66: 3. Change a value: Press and releas
Page 67: Performing a Hard Reset (Reset 1) T
Page 71 and 72: Worksheet Example 2: Daily Configur
Page 73 and 74: XTP CrossPoint 3200 Switchers Confi
Page 75 and 76: Programming Guide The XTP CrossPoin
Page 77 and 78: Establishing a Connection Establish
Page 79 and 80: Outnn•Volxx] The switcher initiat
Page 81 and 82: Table 8. SIS Command vs. Switcher o
Page 83 and 84: Symbol definitions ] = Carriage ret
Page 85 and 86: SIS Command and Response Table for
Page 87 and 88: Table 10. EDID Values X$ Source or
Page 115 and 116: X7( = Port number 01 = Remote RS-23
Page 117 and 118: HTML Operation The XTP CrossPoint M
Page 119 and 120:
Status Tab System Status Page The S
Page 121 and 122:
HDCP Page The HDCP page (see figure
Page 123 and 124:
Unit Name field The Unit Name field
Page 125 and 126:
Passwords Page Access the Passwords
Page 127 and 128:
Setting up SMTP authorization If de
Page 129 and 130:
2. Click the Firmware link. 3. Sele
Page 131 and 132:
File Management Tab File Management
Page 133 and 134:
NOTES: • If you lose track of the
Page 135 and 136:
Output Adjustments Page The Output
Page 137 and 138:
Muting and unmuting an audio output
Page 139 and 140:
Global Presets Page You can save an
Page 141 and 142:
ACT LAN LINK RESET 50-60Hz -A MAX I
Page 143 and 144:
Using the Button-Label Generator so
Page 145 and 146:
XTP CrossPoint 1600 and 3200 Switch
Page 147 and 148:
Pinging to Determine the Extron IP
Page 149 and 150:
6. After verifying that the IP addr
Page 151 and 152:
Help For Telnet command definitions
Page 153:
Extron Warranty Extron Electronics
show all

Extron XTP CrossPoint 1600 and 3200 ... - Extron Electronics

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?