Extron XTP CrossPoint 1600 and 3200 ... - Extron Electronics

More documents

Recommendations

Info

Arrangement of Command and Response Tables Different board types and endpoint types accept different types of commands. There is some repetition in the command and response tables, depending on the input and output for which the commands are appropriate. Additionally, basic whole-switcher commands, more advanced whole-switcher commands, and IP- and remote port setup commands are presented in separate command and response tables. The following pages present seven command and response tables, each defining a subset of SIS commands and their responses, with examples where appropriate. The tables that are presented are listed below. For increased detail as to where each command family is presented, see table 8, on the next page and table 9 on page 76. • SIS Command and Response Table for Basic Matrix Switcher Commands, starting on page 79 — SIS commands for basic, everyday functions of the XTP CrossPoint switcher frame. • SIS Command and Response Table for Input-Board-Specific Commands, starting on page 80 — SIS commands to control and monitor the inputs to the matrix switcher via assorted input boards. • SIS Command and Response Table for Input-Endpoint-Specific Commands, starting on page 88 — SIS commands to control and monitor the XTP T HDMI transmitter and XTP USW 103 switcher input endpoints from the matrix switcher. • SIS Command and Response Table for Output-Board-Specific Commands, starting on page 95 — SIS commands to control and monitor the outputs from the matrix switcher via assorted output boards. • SIS Command and Response Table for Output-Endpoint-Specific Commands, starting on page 99 — SIS commands to control and monitor the XTP R HDMI receiver endpoint from the matrix switcher. • SIS Command and Response Table for Advanced Matrix Switcher Commands, starting on page 103 — SIS commands for advanced functions of the XTP CrossPoint switcher frame. • SIS Command and Response Table for IP- and Remote Port-Specific Commands, starting on page 109 — SIS commands to control and monitor the IP interface and Remote RS-232/RS-422 port of the XTP CrossPoint matrix switcher. XTP CrossPoint 1600 and 3200 Switchers • Programming Guide 74
Table 8. SIS Command vs. Switcher or Board Type Cross-Reference, Basic and Input Commands Input boards Input Endpoints Command family Create ties Page 79 View ties Page 80 Recall global presets Page 80 Basic XTP HDMI DVI Pro VGA XTP T HDMI transmitter XTP USW 103 switcher XTP T VGA transmitter XTP T FB 202 XTP T UWP 202 XTP T UWP 302 switchers EDID Page 80 Page 80 Page 80 Page 80 Page 88 Page 88 Page 88 Page 88 Input sync detection Page 83 Page 83 Page 83 Page 83 Page 89 Page 91 Page 93 Page 94 Input audio level N/A Page 83 Page 83 Page 83 Page 88 Page 88 Page 88 Page 88 Audio routing selections N/A Page 83 Page 83 N/A Page 89 Page 91 N/A Page 93 HDCP authorized device N/A Page 83 Page 83 N/A Page 89 Page 91 N/A Page 94 HDCP status N/A Page 84 Page 84 N/A Page 89 Page 91 N/A Page 94 Captive screw and Ethernet Page 84 N/A N/A N/A serial port insertions Ethernet serial port insert Page 84 N/A N/A N/A parameters XTP power Page 85 N/A N/A N/A Input video format N/A N/A N/A Page 85 N/A Page 90 Page 91 Page 94 Auto-Image N/A N/A N/A Page 86 N/A Page 90 Page 91 Page 94 Color N/A N/A N/A Page 86 N/A N/A Page 92 N/A Tint N/A N/A N/A Page 86 N/A N/A Page 92 N/A Brightness N/A N/A N/A Page 86 N/A N/A Page 92 N/A Contrast N/A N/A N/A Page 86 N/A N/A Page 92 N/A Pixel phase N/A N/A N/A Page 86 N/A Page 90 Page 92 Page 94 Horizontal shift N/A N/A N/A Page 87 N/A Page 90 Page 93 Page 94 Vertical shift N/A N/A N/A Page 87 N/A Page 90 Page 93 Page 94 Save and recall analog input presets N/A N/A N/A Page 87 N/A Page 90 Page 93 N/A XTP CrossPoint 1600 and 3200 Switchers • Programming Guide 75
Page 1 and 2:
User Guide Matrix Switchers XTP Cro
Page 3 and 4:
Conventions Used in this Guide Noti
Page 5 and 6:
Contents Introduction..............
Page 7 and 8:
IR STANDBY/ON CONFIG CHANNEL SDTV E
Page 9 and 10:
The matrix switchers can be remotel
Page 11 and 12:
HDMI and DVI Pro input and output b
Page 13 and 14:
HDMI 1.3 compatible — Supports HD
Page 15 and 16:
Installation This sections details
Page 17 and 18:
LAN RS 232/RS422 1 2 REMOTE 3 4 ACT
Page 19 and 20:
1d IR/RS-232 Over XTP Connectors
Page 21 and 22:
XTP CP 4o HDMI (HDMI Output board)
Page 23 and 24:
XTP board XTP ports — The XTP inp
Page 25 and 26:
Use the LockIt Lacing Brackets, sup
Page 27 and 28:
The level for each analog audio inp
Page 29 and 30: Front Panel Configuration Port and
Page 31 and 32: XTP CROSSPOINT 3200 1 2 INPUTS 1 2
Page 33 and 34: Control Buttons Primary functions N
Page 35 and 36: I/O Controls NOTE: See Front Panel
Page 37 and 38: Definitions The following Extron ma
Page 39 and 40: Example 1: Create a set of video an
Page 41 and 42: The current configuration (see figu
Page 43 and 44: Viewing the Configuration The curre
Page 45 and 46: 5. Deselect video: Press and releas
Page 47 and 48: Example 5: Saving a preset In the f
Page 49 and 50: Muting and Unmuting Video and Audio
Page 51 and 52: INPUTS OUTPUTS CONFIG PRIMARY 1 2 R
Page 53 and 54: Table 4. XTP CrossPoint 3200 Audio
Page 55 and 56: Example 8: Viewing and adjusting an
Page 57 and 58: Viewing and Adjusting the Analog Ou
Page 59 and 60: Table 6. Audio Volume Display Highe
Page 61 and 62: 4. Change the volume: Press and rel
Page 63 and 64: Selecting Lock mode 2 or toggling b
Page 65 and 66: 3. Change a value: Press and releas
Page 67 and 68: Performing a Hard Reset (Reset 1) T
Page 69 and 70: Optimizing the Analog Audio Trouble
Page 71 and 72: Worksheet Example 2: Daily Configur
Page 73 and 74: XTP CrossPoint 3200 Switchers Confi
Page 75 and 76: Programming Guide The XTP CrossPoin
Page 77 and 78: Establishing a Connection Establish
Page 79: Outnn•Volxx] The switcher initiat
Page 83 and 84: Symbol definitions ] = Carriage ret
Page 85 and 86: SIS Command and Response Table for
Page 87 and 88: Table 10. EDID Values X$ Source or
Page 115 and 116: X7( = Port number 01 = Remote RS-23
Page 117 and 118: HTML Operation The XTP CrossPoint M
Page 119 and 120: Status Tab System Status Page The S
Page 121 and 122: HDCP Page The HDCP page (see figure
Page 123 and 124: Unit Name field The Unit Name field
Page 125 and 126: Passwords Page Access the Passwords
Page 127 and 128: Setting up SMTP authorization If de
Page 129 and 130: 2. Click the Firmware link. 3. Sele
Page 131 and 132:
File Management Tab File Management
Page 133 and 134:
NOTES: • If you lose track of the
Page 135 and 136:
Output Adjustments Page The Output
Page 137 and 138:
Muting and unmuting an audio output
Page 139 and 140:
Global Presets Page You can save an
Page 141 and 142:
ACT LAN LINK RESET 50-60Hz -A MAX I
Page 143 and 144:
Using the Button-Label Generator so
Page 145 and 146:
XTP CrossPoint 1600 and 3200 Switch
Page 147 and 148:
Pinging to Determine the Extron IP
Page 149 and 150:
6. After verifying that the IP addr
Page 151 and 152:
Help For Telnet command definitions
Page 153:
Extron Warranty Extron Electronics
show all

Extron XTP CrossPoint 1600 and 3200 ... - Extron Electronics

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?