Extron XTP CrossPoint 1600 and 3200 ... - Extron Electronics

More documents

Recommendations

Info

SIS Command and Response Table for Basic Matrix Switcher Commands (continued) Command Function SIS Command (Host to Unit) Response (Unit to Host) Additional description Read ties NOTE: The & read tie command for RGB and the % read tie command for video can be used interchangeably on the matrix switchers. Read RGB (video) output tie X@ & X!] RGB input X! is tied to output X@. Read video output tie X@ % X!] Video input X! is tied to output X@. Read audio output tie X@ $ X!] Audio input X! is tied to output X@. Recall global input presets NOTES: • Save presets from the front panel (see Example 5: Saving a preset on page 41) or via the Save current configuration as a global preset SIS command on page 104). • If you try to recall a global preset that is not saved, the matrix switcher responds with the error code E11. Recall a global preset X# . Rpr X#] Command character is a period. Example: 5. Rpr05] Recall preset 5, which becomes the current configuration. SIS Command and Response Table for Input-Board-Specific Commands The table that starts below shows commands that affect inputs only and, in general, apply to installed input boards. Where a command does not apply to all input board types, the valid board types are noted. Command Function SIS Command (Host to Unit) Response (Unit to Host) Additional description EDID commands NOTES: • See table 10, on the next two pages for X$ values. • Leading zeroes are optional for the entry of the inputs (X^s) and EDID values (X$s). Leading zeroes are reported in the response. Assign EDID data to an input E A X^*X$ EDID } EdidAX^*X$] Assign an EDID value of X$ to input X^. Example (XTP CrossPoint 3200): E A7*36EDID } EdidA07*036] Assign an EDID value of 1280x720 at 60 Hz to input 7. Example (XTP CrossPoint 1600): E A7*36EDID } EdidA07*036] Assign an EDID value of 1600x900 at 60 Hz to input 7. Assign EDID data to all inputs E A* X$ *EDID } EdidA00*X$] Assign an EDID value of X$ to all inputs. View EDID assignment E A X^EDID } X$] NOTE: The “EdidA” portion of the View command response appears only when the switcher is in Verbose mode 2 or 3 (see the Verbose Mode SIS command on page 110). Save output 1 EDID to user assigned slot E S X$ EDID ] EdidSX$] Save the output 1 EDID to location X$. NOTE: For this command, X$ is valid only in the range of 117 through 124 (XTP CrossPoint 1600) or 133 through 140 (XTP CrossPoint 3200). Example (XTP CrossPoint 3200): E S133EDID } EdidS133] Save the output 1 EDID to user location 1. Example (XTP CrossPoint 1600): E S117EDID } EdidS117] Save the output 1 EDID to user location 1. NOTE: X! = Input number (for tie) 00 – 16 or 32 (00 = untied) X@ = Output number 01 – 16 or 32 X# = Global preset number 01 - 32 X$ = EDID value (resolution and rate) See table 10 on the next page. X^ = Input number (for other than tie) 01 – 16 or 32 XTP CrossPoint 1600 and 3200 Switchers • Programming Guide 80
Table 10. EDID Values X$ Source or value X$ Source or value X$ Source or value X$ Source or value X$ Source or value XTP CrossPoint 1600 and 3200 Switchers • Programming Guide 81 3200 1600 3200 1600 3200 1600 3200 1600 3200 1600 Assigned output values 001 001 Output 1 008 008 Output 8 015 015 Output 15 022 Output 22 029 Output 29 002 002 Output 2 009 009 Output 9 016 016 Output 16 023 Output 23 030 Output 30 003 003 Output 3 010 010 Output 10 017 Output 17 024 Output 24 031 Output 31 004 004 Output 4 011 011 Output 11 018 Output 18 025 Output 25 032 Output 32 005 005 Output 5 012 012 Output 12 019 Output 19 026 Output 26 006 006 Output 6 013 013 Output 13 020 Output 20 027 Output 27 007 007 Output 7 014 014 Output 14 021 Output 21 028 Output 28 VGA – PC values 033 017 1024x768 @ 50 Hz 040 024 1280x800 @ 60 Hz 047 031 1400x1050 @ 50 Hz 054 038 1600x1200 @ 60 Hz 061 045 2048x1080 @ 50 Hz 034 018 1024x768 @ 60 Hz 041 025 1280x1024 @ 50 Hz 048 032 1400x1050 @ 60 Hz 055 039 1680x1050 @ 50 Hz 062 046 2048x1080 @ 60 Hz 035 019 1280x720 @ 50 Hz 042 026 1280x1024 @ 60 Hz 049 033 1440x900 @ 50 Hz 056 040 1680x1050 @ 60 Hz 036 020 1280x720 @ 60 Hz 043 027 1360x768 @ 50 Hz 050 034 1440x900 @ 60 Hz 057 041 1920x1080 @ 50 Hz 037 021 1280x768 @ 50 Hz 044 028 1360x768 @ 60 Hz 051 035 1600x900 @ 50 Hz 058 042 1920x1080 @ 60 Hz 038 022 1280x768 @ 60 Hz 045 029 1366x768 @ 50 Hz 052 036 1600x900 @ 60 Hz 059 043 1920x1200 @ 50 Hz 039 023 1280x800 @ 50 Hz 046 030 1366x768 @ 60 Hz 053 037 1600x1200 @ 50 Hz 060 044 1920x1200 @ 60 Hz DVI – PC values 063 047 1024x768 @ 50 Hz 070 054 1280x800 @ 60 Hz 077 061 1400x1050 @ 50 Hz 084 068 1600x1200 @ 60 Hz 091 075 2048x1080 @ 50 Hz 064 048 1024x768 @ 60 Hz 071 055 1280x1024 @ 50 Hz 078 062 1400x1050 @ 60 Hz 085 069 1680x1050 @ 50 Hz 092 076 2048x1080 @ 60 Hz 065 049 1280x720 @ 50 Hz 072 056 1280x1024 @ 60 Hz 079 063 1440x900 @ 50 Hz 086 070 1680x1050 @ 60 Hz 066 050 1280x720 @ 60 Hz 073 057 1360x768 @ 50 Hz 080 064 1440x900 @ 60 Hz 087 071 1920x1080 @ 50 Hz 067 051 1280x768 @ 50 Hz 074 058 1360x768 @ 60 Hz 081 065 1600x900 @ 50 Hz 088 072 1920x1080 @ 60 Hz 068 052 1280x768 @ 60 Hz 075 059 1366x768 @ 50 Hz 082 066 1600x900 @ 60 Hz 089 073 1920x1200 @ 50 Hz 069 053 1280x800 @ 50 Hz 076 060 1366x768 @ 60 Hz 083 067 1600x1200 @ 50 Hz 090 074 1920x1200 @ 60 Hz
Page 1 and 2:
User Guide Matrix Switchers XTP Cro
Page 3 and 4:
Conventions Used in this Guide Noti
Page 5 and 6:
Contents Introduction..............
Page 7 and 8:
IR STANDBY/ON CONFIG CHANNEL SDTV E
Page 9 and 10:
The matrix switchers can be remotel
Page 11 and 12:
HDMI and DVI Pro input and output b
Page 13 and 14:
HDMI 1.3 compatible — Supports HD
Page 15 and 16:
Installation This sections details
Page 17 and 18:
LAN RS 232/RS422 1 2 REMOTE 3 4 ACT
Page 19 and 20:
1d IR/RS-232 Over XTP Connectors
Page 21 and 22:
XTP CP 4o HDMI (HDMI Output board)
Page 23 and 24:
XTP board XTP ports — The XTP inp
Page 25 and 26:
Use the LockIt Lacing Brackets, sup
Page 27 and 28:
The level for each analog audio inp
Page 29 and 30:
Front Panel Configuration Port and
Page 31 and 32:
XTP CROSSPOINT 3200 1 2 INPUTS 1 2
Page 33 and 34:
Control Buttons Primary functions N
Page 35 and 36: I/O Controls NOTE: See Front Panel
Page 37 and 38: Definitions The following Extron ma
Page 39 and 40: Example 1: Create a set of video an
Page 41 and 42: The current configuration (see figu
Page 43 and 44: Viewing the Configuration The curre
Page 45 and 46: 5. Deselect video: Press and releas
Page 47 and 48: Example 5: Saving a preset In the f
Page 49 and 50: Muting and Unmuting Video and Audio
Page 51 and 52: INPUTS OUTPUTS CONFIG PRIMARY 1 2 R
Page 53 and 54: Table 4. XTP CrossPoint 3200 Audio
Page 55 and 56: Example 8: Viewing and adjusting an
Page 57 and 58: Viewing and Adjusting the Analog Ou
Page 59 and 60: Table 6. Audio Volume Display Highe
Page 61 and 62: 4. Change the volume: Press and rel
Page 63 and 64: Selecting Lock mode 2 or toggling b
Page 65 and 66: 3. Change a value: Press and releas
Page 67 and 68: Performing a Hard Reset (Reset 1) T
Page 69 and 70: Optimizing the Analog Audio Trouble
Page 71 and 72: Worksheet Example 2: Daily Configur
Page 73 and 74: XTP CrossPoint 3200 Switchers Confi
Page 75 and 76: Programming Guide The XTP CrossPoin
Page 77 and 78: Establishing a Connection Establish
Page 79 and 80: Outnn•Volxx] The switcher initiat
Page 81 and 82: Table 8. SIS Command vs. Switcher o
Page 83 and 84: Symbol definitions ] = Carriage ret
Page 85: SIS Command and Response Table for
Page 89 and 90: SIS Command and Response Table for
Page 115 and 116: X7( = Port number 01 = Remote RS-23
Page 117 and 118: HTML Operation The XTP CrossPoint M
Page 119 and 120: Status Tab System Status Page The S
Page 121 and 122: HDCP Page The HDCP page (see figure
Page 123 and 124: Unit Name field The Unit Name field
Page 125 and 126: Passwords Page Access the Passwords
Page 127 and 128: Setting up SMTP authorization If de
Page 129 and 130: 2. Click the Firmware link. 3. Sele
Page 131 and 132: File Management Tab File Management
Page 133 and 134: NOTES: • If you lose track of the
Page 135 and 136: Output Adjustments Page The Output
Page 137 and 138:
Muting and unmuting an audio output
Page 139 and 140:
Global Presets Page You can save an
Page 141 and 142:
ACT LAN LINK RESET 50-60Hz -A MAX I
Page 143 and 144:
Using the Button-Label Generator so
Page 145 and 146:
XTP CrossPoint 1600 and 3200 Switch
Page 147 and 148:
Pinging to Determine the Extron IP
Page 149 and 150:
6. After verifying that the IP addr
Page 151 and 152:
Help For Telnet command definitions
Page 153:
Extron Warranty Extron Electronics
show all

Extron XTP CrossPoint 1600 and 3200 ... - Extron Electronics

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?