Extron XTP CrossPoint 1600 and 3200 ... - Extron Electronics

More documents

Recommendations

Info

XTP Power Page The XTP Power page (see figure 64) provides a location to enable and disable PoX for all XTP inputs and outputs. Access the XTP Power page by clicking the XTP Power link on the left of theon the Set and View Ties, Input Adjustments, Output Adjustments, EDID Configuration, or Presets page. Select (check) and deselect (uncheck) the Enable Power box. NOTES: • PoX is supplied by the XTP CrossPoint 48 V power supply. • XTP CrossPoint 1600: • Can power up to 28 total (input and output) endpoints at up to 364 watts. • Is available with optional 48 V power supply redundancy. • The XTP CrossPoint 3200: • Can power up to 24 total (input and output) endpoints at up to 312 watts. • No 48 V power supply redundancy is available. Figure 64. XTP Power Page XTP CrossPoint 1600 and 3200 Switchers • HTML Operation 132
Global Presets Page You can save and recall global presets from the Global Presets page (see figure 65). Access the Global presets page by clicking the Global Presets link on the left of the Set and View Ties, Input Adjustments, Output Adjustments, EDID Configuration, or XTP Power page. Figure 65. Global Presets Page Saving a preset Save the current configuration (configuration 0) as a preset as follows: 1. Click the Save Preset button. 2. Select the desired preset by clicking on one of the presets listed. To create a new preset, click one of the [unassigned] buttons. Overwrite an existing preset by clicking an already existing preset. 3. If desired, type over the current name in the box adjacent to the Save Preset button. NOTE: The HTML language reserves certain characters for specific functions (see Special Characters on page 110. If you do not rename an unassigned button, the XTP CrossPoint switcher names the preset as Preset {next available number}. If you do not rename an existing preset when it is overwritten, the XTP CrossPoint switcher retains the same name. 4. Click the Accept button. Recalling a preset To recall a global preset as the current configuration, click the button associated with the desired preset. XTP CrossPoint 1600 and 3200 Switchers • HTML Operation 133
Page 1 and 2:
User Guide Matrix Switchers XTP Cro
Page 3 and 4:
Conventions Used in this Guide Noti
Page 5 and 6:
Contents Introduction..............
Page 7 and 8:
IR STANDBY/ON CONFIG CHANNEL SDTV E
Page 9 and 10:
The matrix switchers can be remotel
Page 11 and 12:
HDMI and DVI Pro input and output b
Page 13 and 14:
HDMI 1.3 compatible — Supports HD
Page 15 and 16:
Installation This sections details
Page 17 and 18:
LAN RS 232/RS422 1 2 REMOTE 3 4 ACT
Page 19 and 20:
1d IR/RS-232 Over XTP Connectors
Page 21 and 22:
XTP CP 4o HDMI (HDMI Output board)
Page 23 and 24:
XTP board XTP ports — The XTP inp
Page 25 and 26:
Use the LockIt Lacing Brackets, sup
Page 27 and 28:
The level for each analog audio inp
Page 29 and 30:
Front Panel Configuration Port and
Page 31 and 32:
XTP CROSSPOINT 3200 1 2 INPUTS 1 2
Page 33 and 34:
Control Buttons Primary functions N
Page 35 and 36:
I/O Controls NOTE: See Front Panel
Page 37 and 38:
Definitions The following Extron ma
Page 39 and 40:
Example 1: Create a set of video an
Page 41 and 42:
The current configuration (see figu
Page 43 and 44:
Viewing the Configuration The curre
Page 45 and 46:
5. Deselect video: Press and releas
Page 47 and 48:
Example 5: Saving a preset In the f
Page 49 and 50:
Muting and Unmuting Video and Audio
Page 51 and 52:
INPUTS OUTPUTS CONFIG PRIMARY 1 2 R
Page 53 and 54:
Table 4. XTP CrossPoint 3200 Audio
Page 55 and 56:
Example 8: Viewing and adjusting an
Page 57 and 58:
Viewing and Adjusting the Analog Ou
Page 59 and 60:
Table 6. Audio Volume Display Highe
Page 61 and 62:
4. Change the volume: Press and rel
Page 63 and 64:
Selecting Lock mode 2 or toggling b
Page 65 and 66:
3. Change a value: Press and releas
Page 67 and 68:
Performing a Hard Reset (Reset 1) T
Page 69 and 70:
Optimizing the Analog Audio Trouble
Page 71 and 72:
Worksheet Example 2: Daily Configur
Page 73 and 74:
XTP CrossPoint 3200 Switchers Confi
Page 75 and 76:
Programming Guide The XTP CrossPoin
Page 77 and 78:
Establishing a Connection Establish
Page 79 and 80:
Outnn•Volxx] The switcher initiat
Page 81 and 82:
Table 8. SIS Command vs. Switcher o
Page 83 and 84:
Symbol definitions ] = Carriage ret
Page 85 and 86:
SIS Command and Response Table for
Page 87 and 88: Table 10. EDID Values X$ Source or
Page 89 and 90: SIS Command and Response Table for
Page 115 and 116: X7( = Port number 01 = Remote RS-23
Page 117 and 118: HTML Operation The XTP CrossPoint M
Page 119 and 120: Status Tab System Status Page The S
Page 121 and 122: HDCP Page The HDCP page (see figure
Page 123 and 124: Unit Name field The Unit Name field
Page 125 and 126: Passwords Page Access the Passwords
Page 127 and 128: Setting up SMTP authorization If de
Page 129 and 130: 2. Click the Firmware link. 3. Sele
Page 131 and 132: File Management Tab File Management
Page 133 and 134: NOTES: • If you lose track of the
Page 135 and 136: Output Adjustments Page The Output
Page 137: Muting and unmuting an audio output
Page 141 and 142: ACT LAN LINK RESET 50-60Hz -A MAX I
Page 143 and 144: Using the Button-Label Generator so
Page 145 and 146: XTP CrossPoint 1600 and 3200 Switch
Page 147 and 148: Pinging to Determine the Extron IP
Page 149 and 150: 6. After verifying that the IP addr
Page 151 and 152: Help For Telnet command definitions
Page 153: Extron Warranty Extron Electronics
show all

Extron XTP CrossPoint 1600 and 3200 ... - Extron Electronics

Create successful ePaper yourself

Delete template?

Save as template?