Extron XTP CrossPoint 1600 and 3200 ... - Extron Electronics

SIS Command and Response Table for Output-Endpoint-Specific Commands (continued)
Command Function
SIS Command
(Host to Unit to Endpoint)
Response
(Endpoint to Unit to Host)
Additional description
XTP SR HDMI scaler specific commands
Video mutes
Video mute X@ *1B Vmt X@ *1 ] Mute output X@ video (video off).
Video unmute X@ *0B Vmt X@ *0 ] Unmute output X@ video (video on).
Read video mute X@ B X2#] X2# = 1 = enable (muted)
0 = disable (unmuted) (default).
Global video mute 1*B Vmt1] Mute all video outputs.
Global video unmute 0*B Vmt0] Unmute all video outputs.
Audio routing selections
NOTES:
• These commands select between the audio embedded in the digital video stream and the 2-channel analog audio.
• These commands are valid only if audio breakaway switching is performed (see the Create Ties commands on page 79)
Output audio HDMI select E O X@ * X3# AFMT } AfmtOX@ * X3#] When audio is broken away from video,
embed audio from the X3# source in the
video output.
Example: E O3*0AFMT } AfmtO03*0] When audio is broken away from video,
use the embedded audio from the input
port when creating an audio breakaway
tie to output 3.
View output audio breakaway E O X@ AFMT }
X3#]
selection
View output audio breakaway
selection, all outputs
E OAFMT } X3# 1 X3# 2 X3# 3 ... X3# n ] 16 or 32 ( n ) sequential audio output
selections, starting from output 1.
Audio output volume
Set the audio volume to a specific X@ * X3% V
Out X@ •Vol X3%]
value
Example: 1*50v Out01•Vol50] Set output 1 volume to 79%.
Increment volume X@ +V Out X@ •Vol X3%] Increment volume by 1 step.
Example: 1+V Out01•Vol51]
Decrement volume X@ -V Out X@ •Vol X3%] Decrease volume by 1 step.
Read output volume X@ V X3%]
Audio mutes
Mute digital audio X@ *1Z Amt X@ *1 ] Mute output X@ digital audio (audio off).
Mute analog audio X@ *2Z Amt X@ *2 ] Mute output X@ analog audio (audio off).
Mute digital and analog audio X@ *3Z Amt X@ *3 ]
Unmute both audio X@ *0Z Amt X@ *0 ] Unmute output X@ audio (audio on).
View audio mute status X@ Z X3^]
Global digital audio mute 1*Z Amt1] Mute all audio digital outputs.
Global analog audio mute 2*Z Amt2] Mute all analog audio outputs.
Global digital and audio mute 3*Z Amt3] Mute all digital and and audio outputs.
Global audio unmute 0*Z Amt0] Unmute all audio outputs.
NOTE: X@ = Output number 01 – 16 or 32
X2# = Enable and disable for mutes 0 = Disable 1 = Enable
X3# = Output audio source 0 = Original HDMI audio 1 = Embed audio
X3% = Volume 00 – 64 (1 dB per step except for 0-to-1, which is 13 dB). See table 11 on page 96.
X3^ = Digital and analog audio mute status 0 = No mutes 2 = Analog audio mute
1 = Digital audio mute 3 = Digital and analog audio mute
XTP CrossPoint 1600 and 3200 Switchers • Programming Guide 101