Extron XTP CrossPoint 1600 and 3200 ... - Extron Electronics

More documents

Recommendations

Info

SIS Command and Response Table for Input-Board-Specific Commands (continued) Command Function SIS Command (Host to Unit) Response (Unit to Host) Additional description Inputs on XTP CP 4i VGA (Analog Video) Boards (continued) Auto-Image Execute Auto-Image X^A AadjI X^] Execute image sizing, centering, and filtering adjustments on input X^. Color NOTE: Color adjustments are available for RBGcvS (SCART), interlaced component video (YUVi), S-video, and NTSC composite video inputs. Set a specific color value E I X^*X3) COLR } ColrIX^*X3)] Specify the color adjustment. Increment color value E I X^+COLR } ColrIX^*X3)] Increase the color setting by one. Decrement color value E I X^–COLR } ColrIX^*X3)] Decrease the color setting by one. View the color value E I X^COLR } X3)] Show the color setting. Tint NOTE: Tint adjustments are available for NTSC S-video, and NTSC composite video inputs. Set a specific tint value E I X^*X3) TINT } TintIX^*X3)] Specify the tint adjustment. Increment tint value E I X^+TINT } TintIX^*X3)] Increase the tint setting by one. Decrement tint value E I X^–TINT } TintIX^*X3)] Decrease the tint setting by one. View the tint value E I X^TINT } X3)] Show the tint setting. Brightness NOTE: Brightness adjustments are available for RBGcvS (SCART), interlaced component video (YUVi), S-video, and NTSC composite video inputs. Set a specific brightness value E I X^*X3) BRIT } BritIX^*X3)] Specify the brightness adjustment. Increment brightness value E I X^+BRIT } BritIX^*X3)] Increase the brightness setting by one. Decrement brightness value E I X^–BRIT } BritIX^*X3)] Decrease the brightness setting by one. View the brightness value E I X^BRIT } X3)] Show the brightness setting. Contrast NOTE: Contrast adjustments are available for RBGcvS (SCART), interlaced component video (YUVi), S-video, and NTSC composite video inputs. Set a specific contrast value E I X^*X3) CONT } ContIX^*X3)] Specify the contrast adjustment. Increment contrast value E I X^+CONT } ContIX^*X3)] Increase the contrast setting by one. Decrement contrast value E I X^–CONT } ContIX^*X3)] Decrease the contrast setting by one. View the contrast value E I X^CONT } X3)] Show the contrast setting. Pixel phase NOTE: Pixel phase adjustments are available for RBGHV and non-interlaced component video (YUVp) video inputs. Set a specific pixel sampling phase E I X^*X3) PHAS } PhasIX^*X3)] Specify the pixel sampling phase. Increment sampling value E I X^+PHAS } PhasIX^*X3)] Increase the phase value. Decrement sampling value E I X^–PHAS } PhasIX^*X3)] Decrease the phase value. View the sampling value E I X^PHAS } X3)] Show the pixel sampling phase. NOTE: X^ = Input number (for other than tie) 01 – 16 or 32 X3) = Picture adjustments 000 through 255 (128 = default) XTP CrossPoint 1600 and 3200 Switchers • Programming Guide 86
SIS Command and Response Table for Input-Board-Specific Commands (continued) Command Function SIS Command (Host to Unit) Response (Unit to Host) Additional description Inputs on XTP CP 4i VGA (Analog Video) Boards (continued) Horizontal shift Specify a value E I X^*X3! HCTR } HctrIX^*X3!] Set the horizontal location of first active pixel in input X^. Increment value E I X^–HCTR } HctrIX^*X3!] Increment the value by one pixel (shift the image to the right). Decrement value E I X^+HCTR } HctrIX^*X3!] Decrement the value by one pixel (shift the image to the left). View E I X^HCTR } X3!] Show the horizontal location of first active pixel in input X^. Vertical shift Specify a value E I X^*X3! VCTR } VctrIX^*X3!] Set the vertical location of first active pixel in input X^. Increment value E I X^+VCTR } VctrIX^*X3!] Increment the value by one line (shift up). Decrement value E I X^–VCTR } VctrIX^*X3!] Decrease the value by one line (shift down). View E I X^VCTR } X3!] Show the vertical location of first active pixel in input X^. Save and recall analog input presets NOTES: • Analog input presets are available for analog (RGB, YUVp, YUVi, S-video, composite) video input signals on an XTP CP 4i VGA universal analog input board only. • Analog input presets save a set of analog variables, such as: horizontal and vertical shift, pixel phase, color and tint, brightness and contrast, input type, and audio input level (gain and attenuation). Save an analog input preset X^*1*X3@. SprX^*1*X3@] Command character is a period. Recall an analog input preset X^*1*X3@, RprX^*1*X3@] NOTE: X^ = Input number (for other than tie) 01 – 16 or 32 X3! = Shift 00000 through 65535 X3@ = Analog input preset 1 through 8 XTP CrossPoint 1600 and 3200 Switchers • Programming Guide 87
Page 1 and 2:
User Guide Matrix Switchers XTP Cro
Page 3 and 4:
Conventions Used in this Guide Noti
Page 5 and 6:
Contents Introduction..............
Page 7 and 8:
IR STANDBY/ON CONFIG CHANNEL SDTV E
Page 9 and 10:
The matrix switchers can be remotel
Page 11 and 12:
HDMI and DVI Pro input and output b
Page 13 and 14:
HDMI 1.3 compatible — Supports HD
Page 15 and 16:
Installation This sections details
Page 17 and 18:
LAN RS 232/RS422 1 2 REMOTE 3 4 ACT
Page 19 and 20:
1d IR/RS-232 Over XTP Connectors
Page 21 and 22:
XTP CP 4o HDMI (HDMI Output board)
Page 23 and 24:
XTP board XTP ports — The XTP inp
Page 25 and 26:
Use the LockIt Lacing Brackets, sup
Page 27 and 28:
The level for each analog audio inp
Page 29 and 30:
Front Panel Configuration Port and
Page 31 and 32:
XTP CROSSPOINT 3200 1 2 INPUTS 1 2
Page 33 and 34:
Control Buttons Primary functions N
Page 35 and 36:
I/O Controls NOTE: See Front Panel
Page 37 and 38:
Definitions The following Extron ma
Page 39 and 40:
Example 1: Create a set of video an
Page 41 and 42: The current configuration (see figu
Page 43 and 44: Viewing the Configuration The curre
Page 45 and 46: 5. Deselect video: Press and releas
Page 47 and 48: Example 5: Saving a preset In the f
Page 49 and 50: Muting and Unmuting Video and Audio
Page 51 and 52: INPUTS OUTPUTS CONFIG PRIMARY 1 2 R
Page 53 and 54: Table 4. XTP CrossPoint 3200 Audio
Page 55 and 56: Example 8: Viewing and adjusting an
Page 57 and 58: Viewing and Adjusting the Analog Ou
Page 59 and 60: Table 6. Audio Volume Display Highe
Page 61 and 62: 4. Change the volume: Press and rel
Page 63 and 64: Selecting Lock mode 2 or toggling b
Page 65 and 66: 3. Change a value: Press and releas
Page 67 and 68: Performing a Hard Reset (Reset 1) T
Page 69 and 70: Optimizing the Analog Audio Trouble
Page 71 and 72: Worksheet Example 2: Daily Configur
Page 73 and 74: XTP CrossPoint 3200 Switchers Confi
Page 75 and 76: Programming Guide The XTP CrossPoin
Page 77 and 78: Establishing a Connection Establish
Page 79 and 80: Outnn•Volxx] The switcher initiat
Page 81 and 82: Table 8. SIS Command vs. Switcher o
Page 83 and 84: Symbol definitions ] = Carriage ret
Page 85 and 86: SIS Command and Response Table for
Page 87 and 88: Table 10. EDID Values X$ Source or
Page 91: SIS Command and Response Table for
Page 115 and 116: X7( = Port number 01 = Remote RS-23
Page 117 and 118: HTML Operation The XTP CrossPoint M
Page 119 and 120: Status Tab System Status Page The S
Page 121 and 122: HDCP Page The HDCP page (see figure
Page 123 and 124: Unit Name field The Unit Name field
Page 125 and 126: Passwords Page Access the Passwords
Page 127 and 128: Setting up SMTP authorization If de
Page 129 and 130: 2. Click the Firmware link. 3. Sele
Page 131 and 132: File Management Tab File Management
Page 133 and 134: NOTES: • If you lose track of the
Page 135 and 136: Output Adjustments Page The Output
Page 137 and 138: Muting and unmuting an audio output
Page 139 and 140: Global Presets Page You can save an
Page 141 and 142: ACT LAN LINK RESET 50-60Hz -A MAX I
Page 143 and 144:
Using the Button-Label Generator so
Page 145 and 146:
XTP CrossPoint 1600 and 3200 Switch
Page 147 and 148:
Pinging to Determine the Extron IP
Page 149 and 150:
6. After verifying that the IP addr
Page 151 and 152:
Help For Telnet command definitions
Page 153:
Extron Warranty Extron Electronics
show all

Extron XTP CrossPoint 1600 and 3200 ... - Extron Electronics

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?