Extron XTP CrossPoint 1600 and 3200 ... - Extron Electronics

SIS Command and Response Table for Input-Endpoint-Specific Commands (continued)
Command Function
SIS Command
(Host to Unit to Endpoint)
Response
(Endpoint to Unit to Host)
Additional description
XTP T VGA transmitter specific commands (continued)
Horizontal shift
Specify a value E I X^*X3! HCTR } HctrIX^*X3!] Set the horizontal location of first active
pixel in input X^.
Increment value E I X^–HCTR } HctrIX^*X3!] Increment the value by one pixel (shift
the image to the right).
Decrement value E I X^+HCTR } HctrIX^*X3!] Decrement the value by one pixel (shift
the image to the left).
View E I X^HCTR } X3!] Show the horizontal location of first
active pixel in input X^.
Vertical shift
Specify a value E I X^*X3! VCTR } VctrIX^*X3!] Set the vertical location of first active
pixel in input X^.
Increment value E I X^+VCTR } VctrIX^*X3!] Increment the value by one line (shift up).
Decrement value E I X^–VCTR } VctrIX^*X3!] Decrease the value by one line (shift down).
View E I X^VCTR } X3!] Show the vertical location of first active
pixel in input X^.
Save and recall analog input presets
NOTES:
• Analog input presets are available for analog (RGB, YUVp, YUVi, S-video, composite) video input signals on an XTP CP 4i VGA
universal analog input board only.
• Analog input presets save a set of analog variables, such as: horizontal and vertical shift, pixel phase, color and tint, brightness
and contrast, input type, and audio input level (gain and attenuation).
Save an analog input preset X^*1*X3@. SprX^*1*X3@] Command character is a period.
Recall an analog input preset X^*1*X3@, RprX^*1*X3@]
Input sync detection
View all input connections 0LS X% 1 X% 2 X% 3 ... X% n ] 16 or 32 ( n ) X%s; each is the connection
status of an input, starting from input 1.
Example (XTP CrossPoint 3200): 0LS
No input detected Sync detected Sync detected
Response Status: 0 0 0 1 1 1 0 1 0 0 1 0 1. . .0
Input: 1 2 3 4 5 6 7 8 9 10111213 32
XTP T FB 202, XTP T UWP 202, XTP T UWP 302 switcher specific commands
Audio routing selections
Enable black signal for XTP T
endpoint
E E X^*1AFMT } AfmtEX^*1 ] Enable an audio only tie for the
connected XTP transmitter.
Disable black signal for XTP T
endpoint
E E X^*0AFMT } AfmtEX^*0 ] Disable an audio only tie for the
connected XTP transmitter.
View black signal output status for
XTP T endpoint
E E X^*AFMT } X2#] The black signal status of XTP
transmitter endpoint X^ is X2#.
Input reports as an HDCP-authorized device
HDCP authorized device on E E X^*1HDCP } HdcpEX^*1 ] Set the input as an HDCP authorized device.
HDCP authorized device off E E X^*0HDCP } HdcpEX^*0 ] Set the input as not an HDCP
authorized device.
View HDCP authorized status E E X^HDCP } X1#] Show HDCP authorized device status.
NOTE: X% = Input signal status 0 = No signal detected 1 = Sync detected
X^ = Input number (for other than tie) 01 – 16 or 32
X1# = HDCP authorized device 0 = Off 1 = On (default)
X2# = Enable or disable black video ties 0 = Disable 2 = Enable
X3! = Shift 0 through 65535
X3@ = Analog input preset 1 through 8
XTP CrossPoint 1600 and 3200 Switchers • Programming Guide 93