Extron XTP CrossPoint 1600 and 3200 ... - Extron Electronics

More documents

Recommendations

Info

Email Settings Page Reach the Email Settings page (see figure 55) by clicking the Email Settings link on the left of the System Settings, Passwords, or Firmware Upgrade page. The Email Settings page has fields for setting up the e-mail notification capabilities of the switcher. For the e-mail settings and for each row of the e-mail notification settings, click the Edit button to make the fields available for editing. The button changes to Save. After editing the settings associated with the Edit/Save button, click the Save button. Figure 55. Email Settings Page Mail IP Address field The Mail IP Address field displays the IP address and the domain name of the mail server that handles the e-mail for the facility in which the switcher is installed. Valid IP addresses consist of four 1-, 2-, or 3-digit numeric octets separated by dots (periods). Each field can be numbered from 000 through 255. Leading zeroes, up to three digits total per field, are optional. Values of 256 and above are invalid. XTP CrossPoint 1600 and 3200 Switchers • HTML Operation 120
Setting up SMTP authorization If desired, set the XTP CrossPoint to require SMTP authorization before accepting any e-mail as follows: 1. Click Edit. The button changes to Save. 2. Check the SMTP Authorization Required check box, located below the Domain Name field. This enables the User Name and Password fields below the check box. 3. Enter a user name and a password in the User Name and Password fields. For the XTP CrossPoint to accept their e-mail messages, senders must enter the user name and password. NOTES: • For the User name, any combination of letters, numerals, spaces, and symbols except the comma (,) and the single and double quotation marks (‘ and “) are valid. For the password, all characters except the comma are valid. The user name and password can each be from 1 to 30 characters. • Both a user name and a password must be specified. 4. Click Save to save the user name and password. Deselecting SMTP authorization Remove SMTP authorization as follows: 1. Click Edit. The button changes to Save. 2. Click (deselect) the SMTP Authorization Required check box. 3. Click Save. Domain Name field The Domain Name field displays the domain name that the XTP CrossPoint switcher uses to log on to the e-mail server. Standard domain name conventions (for example: xxx.com) apply. NOTE: The HTML language reserves certain characters for specific functions (see Special Characters on page 110). The @ character is acceptable only as the lead-in to the domain name (such as @folklore.net). Email Address fields The five Email Address fields identify the e-mail addresses of the personnel to whom the XTP CrossPoint switcher e-mails notification of its failure and repair status. Standard e-mail address conventions (nnnnn@xxx.com) apply. The check boxes and drop boxes associated with each address field permit the operator to specify specific criteria under which the switcher will e-mail recipients. In the associated Missing Inputs scroll boxes, select the inputs to monitor for presence or absence of a signal. Check the Fans and Power boxes to monitor the cooling and power supplies. In the associated EMail Options drop box, select whether the recipient is to be e-mailed of failures, fixes, both, not notified, or to be removed from the e-mail list. The Suspend option is useful for temporarily removing personnel from the e-mail list when they are unavailable, such as travelling or on vacation. Deleting an e-mail addressee and clicking the Save button removes the recipient from e-mail notification completely. XTP CrossPoint 1600 and 3200 Switchers • HTML Operation 121
Page 1 and 2:
User Guide Matrix Switchers XTP Cro
Page 3 and 4:
Conventions Used in this Guide Noti
Page 5 and 6:
Contents Introduction..............
Page 7 and 8:
IR STANDBY/ON CONFIG CHANNEL SDTV E
Page 9 and 10:
The matrix switchers can be remotel
Page 11 and 12:
HDMI and DVI Pro input and output b
Page 13 and 14:
HDMI 1.3 compatible — Supports HD
Page 15 and 16:
Installation This sections details
Page 17 and 18:
LAN RS 232/RS422 1 2 REMOTE 3 4 ACT
Page 19 and 20:
1d IR/RS-232 Over XTP Connectors
Page 21 and 22:
XTP CP 4o HDMI (HDMI Output board)
Page 23 and 24:
XTP board XTP ports — The XTP inp
Page 25 and 26:
Use the LockIt Lacing Brackets, sup
Page 27 and 28:
The level for each analog audio inp
Page 29 and 30:
Front Panel Configuration Port and
Page 31 and 32:
XTP CROSSPOINT 3200 1 2 INPUTS 1 2
Page 33 and 34:
Control Buttons Primary functions N
Page 35 and 36:
I/O Controls NOTE: See Front Panel
Page 37 and 38:
Definitions The following Extron ma
Page 39 and 40:
Example 1: Create a set of video an
Page 41 and 42:
The current configuration (see figu
Page 43 and 44:
Viewing the Configuration The curre
Page 45 and 46:
5. Deselect video: Press and releas
Page 47 and 48:
Example 5: Saving a preset In the f
Page 49 and 50:
Muting and Unmuting Video and Audio
Page 51 and 52:
INPUTS OUTPUTS CONFIG PRIMARY 1 2 R
Page 53 and 54:
Table 4. XTP CrossPoint 3200 Audio
Page 55 and 56:
Example 8: Viewing and adjusting an
Page 57 and 58:
Viewing and Adjusting the Analog Ou
Page 59 and 60:
Table 6. Audio Volume Display Highe
Page 61 and 62:
4. Change the volume: Press and rel
Page 63 and 64:
Selecting Lock mode 2 or toggling b
Page 65 and 66:
3. Change a value: Press and releas
Page 67 and 68:
Performing a Hard Reset (Reset 1) T
Page 69 and 70:
Optimizing the Analog Audio Trouble
Page 71 and 72:
Worksheet Example 2: Daily Configur
Page 73 and 74:
XTP CrossPoint 3200 Switchers Confi
Page 75 and 76: Programming Guide The XTP CrossPoin
Page 77 and 78: Establishing a Connection Establish
Page 79 and 80: Outnn•Volxx] The switcher initiat
Page 81 and 82: Table 8. SIS Command vs. Switcher o
Page 83 and 84: Symbol definitions ] = Carriage ret
Page 85 and 86: SIS Command and Response Table for
Page 87 and 88: Table 10. EDID Values X$ Source or
Page 115 and 116: X7( = Port number 01 = Remote RS-23
Page 117 and 118: HTML Operation The XTP CrossPoint M
Page 119 and 120: Status Tab System Status Page The S
Page 121 and 122: HDCP Page The HDCP page (see figure
Page 123 and 124: Unit Name field The Unit Name field
Page 125: Passwords Page Access the Passwords
Page 129 and 130: 2. Click the Firmware link. 3. Sele
Page 131 and 132: File Management Tab File Management
Page 133 and 134: NOTES: • If you lose track of the
Page 135 and 136: Output Adjustments Page The Output
Page 137 and 138: Muting and unmuting an audio output
Page 139 and 140: Global Presets Page You can save an
Page 141 and 142: ACT LAN LINK RESET 50-60Hz -A MAX I
Page 143 and 144: Using the Button-Label Generator so
Page 145 and 146: XTP CrossPoint 1600 and 3200 Switch
Page 147 and 148: Pinging to Determine the Extron IP
Page 149 and 150: 6. After verifying that the IP addr
Page 151 and 152: Help For Telnet command definitions
Page 153: Extron Warranty Extron Electronics
show all

Extron XTP CrossPoint 1600 and 3200 ... - Extron Electronics

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?