Extron XTP CrossPoint 1600 and 3200 ... - Extron Electronics

More documents

Recommendations

Info

SIS Command and Response Table for Input-Endpoint-Specific Commands The table that starts below shows commands that affect XTP T HDMI transmitter, XTP USW 103 switcher, XTP T VGA transmiter, XTP T FB 202 floorbox switcher, and XTP T UWP 202 and XTP T UWP 302 wallplate switcher endpoints connected through XTP input boards only. The XTP CrossPoint switcher acts as a master, forwarding the commands to the endpoint slave. Command Function EDID commands SIS Command (Host to Unit to Endpoint) Response (Endpoint to Unit to Host) Additional description NOTE: Leading zeroes are optional for the entry of the inputs (X^s) and EDID values (X$s). Leading zeroes are reported in the response. Assign EDID data to an input E A X^*X$ EDID } EdidAX^*X$] Assign an EDID value of X$ to input X^. Example (XTP CrossPoint 3200): E A7*36EDID } EdidA07*036] Assign an EDID value of 1280x720 at 60 Hz to input 7. Example (XTP CrossPoint 1600): E A7*36EDID } EdidA07*036] Assign an EDID value of 1600x900 at 60 Hz to input 7. Assign EDID data to all inputs E A* X$ *EDID } EdidA00*X$] Assign an EDID value of X$ to all inputs. View EDID assignment E A X^EDID } X$] NOTE: The “EdidA” portion of the View command response appears only when the switcher is in Verbose mode 2 or 3 (see the Verbose Mode SIS command on page 110). Save output 1 EDID to user assigned slot E S X$ EDID ] EdidSX$] Save the output 1 EDID to location X$. NOTE: For this command, X$ is valid only in the range of 117 through 124 (XTP CrossPoint 1600) or 133 through 140 (XTP CrossPoint 3200). Example (XTP CrossPoint 3200): E S133EDID } EdidS133] Save the output 1 EDID to user location 1. Example (XTP CrossPoint 1600): E S117EDID } EdidS117] Save the output 1 EDID to user location 1. Audio input gain and attenuation NOTE: The set gain (G) and set attenuation (g) commands are case sensitive. Set audio input gain to +dB value X^*X& G In X^•Aud X*] Example: 1*2G In01•Aud+02] Set input 1 audio gain to +2 dB. Set audio input attenuation to -dB X^*X( g In X^•Aud X*] value Increment gain X^+G In X^•Aud X*] Increase gain by 1 dB. Example: 5+G In05•Aud+03] Increase audio input 5 level from +2 dB to +3 dB. Decrement gain X^-G In X^•Aud X*] Decrease gain by 1 dB. Example: 7-G In07•Aud-09] Decrease audio input 7 level from -8 dB to -9 dB. Read input gain X^G X*] Example: 3G -06] Audio input 3 level is at -6 dB. NOTE: X$ = EDID value (resolution and rate) See table 10 beginning on page 81. X^ = Input number (for other than tie) 01 – 16 or 32 X& = Audio gain 0 – 24 (1 dB per step) X* = Numeric dB value –18 to +24 (45 steps of gain or attenuation) (default = 0 dB) X( = Audio attenuation 1 – 18 (1 dB per step) XTP CrossPoint 1600 and 3200 Switchers • Programming Guide 88
SIS Command and Response Table for Input-Endpoint-Specific Commands (continued) Command Function SIS Command (Host to Unit to Endpoint) Response (Endpoint to Unit to Host) Additional description XTP T HDMI transmitter specific commands Audio routing selections Input audio selection E I X^*X1@ AFMT } AfmtIX^*X1@] Use audio from the X1@ source. Example 1: E I1*1AFMT } AfmtI01*1] Use analog audio from the analog audio port of input 1. Example 2: E I1*0AFMT } AfmtI01*0] Auto (0): Digital audio takes priority over analog audio. View input audio selection E I X^AFMT } X1@] View all input audio selections E IAFMT } X1@ 1 X1@ 2 X1@ 3 ... X1@ n ] 16 or 32 ( n ) sequential audio input selections, starting from input 1. Enable black signal for XTP T endpoint E E X^*1AFMT } AfmtEX^*1 ] Enable an audio only tie for the connected XTP transmitter. Disable black signal for XTP T endpoint E E X^*0AFMT } AfmtEX^*0 ] Disable an audio only tie for the connected XTP transmitter. View black signal output status for XTP T endpoint E E X^*AFMT } X2#] The black signal status of XTP transmitter endpoint X@ is X2#. Input reports as an HDCP-authorized device HDCP authorized device on E E X^*1HDCP } HdcpEX^*1 ] Set the input as an HDCP authorized device. HDCP authorized device off E E X^*0HDCP } HdcpEX^*0 ] Set the input as not an HDCP authorized device. View HDCP authorized status E E X^HDCP } X1#] Show HDCP authorized device status. HDCP status View input HDCP status E I X^HDCP } X1$] View HDCP status of all inputs E I*HDCP } X1$ 1 X1$ 2 X1$ 3 ... X1$ n ] Input sync detection View all input connections 0LS X% 1 X% 2 X% 3 ... X% n ] 16 or 32 ( n ) X%s; each is the connection status of an input, starting from input 1. Example (XTP CrossPoint 3200): 0LS No input detected Sync detected Sync detected Response Status: 0 0 0 1 1 1 0 1 0 0 1 0 1. . .0 Input: 1 2 3 4 5 6 7 8 9 10111213 32 NOTE: X% = Input signal status 0 = No signal detected 1 = Sync detected X^ = Input number (for other than tie) 01 – 16 or 32 X1@ = Input audio source 0 = Auto (see the example above) 2 = Analog 2-channel audio 1 = HDMI (de-embedded digital audio) (default) X1# = HDCP authorized device 0 = off 1 = on (default) X1$ = HDCP status (for inputs) 0 = No source device connected 1 = Source connected is HDCP-compliant 2 = Source connected is not HDCP-compliant X2# = Enable or disable 0 = Disable 2 = Enable (default) (for black video ties) XTP CrossPoint 1600 and 3200 Switchers • Programming Guide 89
Page 1 and 2:
User Guide Matrix Switchers XTP Cro
Page 3 and 4:
Conventions Used in this Guide Noti
Page 5 and 6:
Contents Introduction..............
Page 7 and 8:
IR STANDBY/ON CONFIG CHANNEL SDTV E
Page 9 and 10:
The matrix switchers can be remotel
Page 11 and 12:
HDMI and DVI Pro input and output b
Page 13 and 14:
HDMI 1.3 compatible — Supports HD
Page 15 and 16:
Installation This sections details
Page 17 and 18:
LAN RS 232/RS422 1 2 REMOTE 3 4 ACT
Page 19 and 20:
1d IR/RS-232 Over XTP Connectors
Page 21 and 22:
XTP CP 4o HDMI (HDMI Output board)
Page 23 and 24:
XTP board XTP ports — The XTP inp
Page 25 and 26:
Use the LockIt Lacing Brackets, sup
Page 27 and 28:
The level for each analog audio inp
Page 29 and 30:
Front Panel Configuration Port and
Page 31 and 32:
XTP CROSSPOINT 3200 1 2 INPUTS 1 2
Page 33 and 34:
Control Buttons Primary functions N
Page 35 and 36:
I/O Controls NOTE: See Front Panel
Page 37 and 38:
Definitions The following Extron ma
Page 39 and 40:
Example 1: Create a set of video an
Page 41 and 42:
The current configuration (see figu
Page 43 and 44: Viewing the Configuration The curre
Page 45 and 46: 5. Deselect video: Press and releas
Page 47 and 48: Example 5: Saving a preset In the f
Page 49 and 50: Muting and Unmuting Video and Audio
Page 51 and 52: INPUTS OUTPUTS CONFIG PRIMARY 1 2 R
Page 53 and 54: Table 4. XTP CrossPoint 3200 Audio
Page 55 and 56: Example 8: Viewing and adjusting an
Page 57 and 58: Viewing and Adjusting the Analog Ou
Page 59 and 60: Table 6. Audio Volume Display Highe
Page 61 and 62: 4. Change the volume: Press and rel
Page 63 and 64: Selecting Lock mode 2 or toggling b
Page 65 and 66: 3. Change a value: Press and releas
Page 67 and 68: Performing a Hard Reset (Reset 1) T
Page 69 and 70: Optimizing the Analog Audio Trouble
Page 71 and 72: Worksheet Example 2: Daily Configur
Page 73 and 74: XTP CrossPoint 3200 Switchers Confi
Page 75 and 76: Programming Guide The XTP CrossPoin
Page 77 and 78: Establishing a Connection Establish
Page 79 and 80: Outnn•Volxx] The switcher initiat
Page 81 and 82: Table 8. SIS Command vs. Switcher o
Page 83 and 84: Symbol definitions ] = Carriage ret
Page 85 and 86: SIS Command and Response Table for
Page 87 and 88: Table 10. EDID Values X$ Source or
Page 93: SIS Command and Response Table for
Page 115 and 116: X7( = Port number 01 = Remote RS-23
Page 117 and 118: HTML Operation The XTP CrossPoint M
Page 119 and 120: Status Tab System Status Page The S
Page 121 and 122: HDCP Page The HDCP page (see figure
Page 123 and 124: Unit Name field The Unit Name field
Page 125 and 126: Passwords Page Access the Passwords
Page 127 and 128: Setting up SMTP authorization If de
Page 129 and 130: 2. Click the Firmware link. 3. Sele
Page 131 and 132: File Management Tab File Management
Page 133 and 134: NOTES: • If you lose track of the
Page 135 and 136: Output Adjustments Page The Output
Page 137 and 138: Muting and unmuting an audio output
Page 139 and 140: Global Presets Page You can save an
Page 141 and 142: ACT LAN LINK RESET 50-60Hz -A MAX I
Page 143 and 144: Using the Button-Label Generator so
Page 145 and 146:
XTP CrossPoint 1600 and 3200 Switch
Page 147 and 148:
Pinging to Determine the Extron IP
Page 149 and 150:
6. After verifying that the IP addr
Page 151 and 152:
Help For Telnet command definitions
Page 153:
Extron Warranty Extron Electronics
show all

Extron XTP CrossPoint 1600 and 3200 ... - Extron Electronics

Create successful ePaper yourself

Delete template?

Save as template?