Extron XTP CrossPoint 1600 and 3200 ... - Extron Electronics

More documents

Recommendations

Info

Subnet Masks and Octets The subnet mask (see figure 77) is used to determine whether the analog and remote devices are on the same subnet or different subnets. The subnet mask consists of four numeric octets separated by dots. Each octet can be numbered from 000 through 255. Leading zeroes, up to three digits total per octet, are optional. Each octet typically contains either 255 or 0. The octets determine whether or not the same octets of two IP addresses will be compared when determining if two devices are on the same subnet. 255 indicates that this octet will be compared between two IP addresses. Typical Subnet Mask: 255.255.0.0 Octets Figure 77. Typical Subnet Mask 0 indicates that this octet will not be compared between two IP addresses. Determining Whether Devices Are on the Same Subnet To determine the subnet, the IP address of the analog device is compared to the IP address of the remote device (see figure 78). The octets of each address are compared or not compared, depending on the value in the related subnet mask octet. • If a subnet mask octet contains the value 255, the related octets of the IP addresses of the analog device and the remote device are unmasked. Unmasked octets are compared (indicated by ? in figure 78). • If the subnet mask octet contains the value 0, the related octets of the IP addresses of the analog device and remote device are masked. Masked octets are not compared (indicated by X in figure 78). If the unmasked octets of the two IP addresses match (indicated by = in figure 78, example 1), the two addresses are on the same subnet. If the two unmasked fields do not match (indicated by ≠ in figure 78, example 2 and example 3), the addresses are not on the same subnet. Local IP Address: Subnet Mask: Remote IP Address: Match?: Example 1 Example 2 Example 3 192.168.254.254 255.255.0.0 (?.?.X.X) 192.168.2.25 =.=.X.X — Match (Same subnet) 192.168.254.254 255.255.0.0 (?.?.X.X) 190.190.2.25 ≠.≠.X.X — No match (Different subnet) 192.168.254.254 255.255.0.0 (?.?.X.X) 192.190.2.25 =.≠.X.X — No match (Different subnet) Figure 78. Comparing the IP Addresses of the Analog and Remote Devices XTP CrossPoint 1600 and 3200 Switchers • Ethernet Connection 146
Extron Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components, to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is returned within the warranty period, with proof of purchase and description of malfunction to: USA, Canada, South America, and Central America: Extron Electronics 1230 South Lewis Street Anaheim, CA 92805 U.S.A. Europe and Africa: Extron Europe Hanzeboulevard 10 3825 PH Amersfoort The Netherlands Japan: Extron Electronics, Japan Kyodo Building, 16 Ichibancho Chiyoda-ku, Tokyo 102-0082 Japan China: Extron China 686 Ronghua Road Songjiang District Shanghai 201611 China Asia: Extron Asia Pte Ltd 135 Joo Seng Road, #04-01 PM Industrial Bldg. Singapore 368363 Singapore Middle East: Extron Middle East Dubai Airport Free Zone F12, PO Box 293666 United Arab Emirates, Dubai This Limited Warranty does not apply if the fault has been caused by misuse, improper handling care, electrical or mechanical abuse, abnormal operating conditions, or if modifications were made to the product that were not authorized by Extron. NOTE: If a product is defective, please call Extron and ask for an Application Engineer to receive an RA (Return Authorization) number. This will begin the repair process. USA: 714.491.1500 or 800.633.9876 Europe: 31.33.453.4040 Asia: 65.6383.4400 Japan: 81.3.3511.7655 Units must be returned insured, with shipping charges prepaid. If not insured, you assume the risk of loss or damage during shipment. Returned units must include the serial number and a description of the problem, as well as the name of the person to contact in case there are any questions. Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality, performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct, indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of such damage. Please note that laws vary from state to state and country to country, and that some provisions of this warranty may not apply to you. Extron Headquarters +1.800.633.9876 (Inside USA/Canada Only) Extron USA - West Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 FAX +1.919.850.1001 FAX Extron Europe +800.3987.6673 (Inside Europe Only) +31.33.453.4040 +31.33.453.4050 FAX Extron Asia +65.6383.4400 +65.6383.4664 FAX Extron Japan +81.3.3511.7655 +81.3.3511.7656 FAX Extron China +86.21.3760.1568 +86.21.3760.1566 FAX Extron Middle East +971.4.299.1800 +971.4.299.1880 FAX Extron Korea +82.2.3444.1571 +82.2.3444.1575 FAX Extron India 1800.3070.3777 (Inside India Only) +91.80.3055.3777 +91.80.3055.3737 FAX © 2013 Extron Electronics All rights reserved. www.extron.com
Page 1 and 2:
User Guide Matrix Switchers XTP Cro
Page 3 and 4:
Conventions Used in this Guide Noti
Page 5 and 6:
Contents Introduction..............
Page 7 and 8:
IR STANDBY/ON CONFIG CHANNEL SDTV E
Page 9 and 10:
The matrix switchers can be remotel
Page 11 and 12:
HDMI and DVI Pro input and output b
Page 13 and 14:
HDMI 1.3 compatible — Supports HD
Page 15 and 16:
Installation This sections details
Page 17 and 18:
LAN RS 232/RS422 1 2 REMOTE 3 4 ACT
Page 19 and 20:
1d IR/RS-232 Over XTP Connectors
Page 21 and 22:
XTP CP 4o HDMI (HDMI Output board)
Page 23 and 24:
XTP board XTP ports — The XTP inp
Page 25 and 26:
Use the LockIt Lacing Brackets, sup
Page 27 and 28:
The level for each analog audio inp
Page 29 and 30:
Front Panel Configuration Port and
Page 31 and 32:
XTP CROSSPOINT 3200 1 2 INPUTS 1 2
Page 33 and 34:
Control Buttons Primary functions N
Page 35 and 36:
I/O Controls NOTE: See Front Panel
Page 37 and 38:
Definitions The following Extron ma
Page 39 and 40:
Example 1: Create a set of video an
Page 41 and 42:
The current configuration (see figu
Page 43 and 44:
Viewing the Configuration The curre
Page 45 and 46:
5. Deselect video: Press and releas
Page 47 and 48:
Example 5: Saving a preset In the f
Page 49 and 50:
Muting and Unmuting Video and Audio
Page 51 and 52:
INPUTS OUTPUTS CONFIG PRIMARY 1 2 R
Page 53 and 54:
Table 4. XTP CrossPoint 3200 Audio
Page 55 and 56:
Example 8: Viewing and adjusting an
Page 57 and 58:
Viewing and Adjusting the Analog Ou
Page 59 and 60:
Table 6. Audio Volume Display Highe
Page 61 and 62:
4. Change the volume: Press and rel
Page 63 and 64:
Selecting Lock mode 2 or toggling b
Page 65 and 66:
3. Change a value: Press and releas
Page 67 and 68:
Performing a Hard Reset (Reset 1) T
Page 69 and 70:
Optimizing the Analog Audio Trouble
Page 71 and 72:
Worksheet Example 2: Daily Configur
Page 73 and 74:
XTP CrossPoint 3200 Switchers Confi
Page 75 and 76:
Programming Guide The XTP CrossPoin
Page 77 and 78:
Establishing a Connection Establish
Page 79 and 80:
Outnn•Volxx] The switcher initiat
Page 81 and 82:
Table 8. SIS Command vs. Switcher o
Page 83 and 84:
Symbol definitions ] = Carriage ret
Page 85 and 86:
SIS Command and Response Table for
Page 87 and 88:
Table 10. EDID Values X$ Source or
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102: SIS Command and Response Table for
Page 115 and 116: X7( = Port number 01 = Remote RS-23
Page 117 and 118: HTML Operation The XTP CrossPoint M
Page 119 and 120: Status Tab System Status Page The S
Page 121 and 122: HDCP Page The HDCP page (see figure
Page 123 and 124: Unit Name field The Unit Name field
Page 125 and 126: Passwords Page Access the Passwords
Page 127 and 128: Setting up SMTP authorization If de
Page 129 and 130: 2. Click the Firmware link. 3. Sele
Page 131 and 132: File Management Tab File Management
Page 133 and 134: NOTES: • If you lose track of the
Page 135 and 136: Output Adjustments Page The Output
Page 137 and 138: Muting and unmuting an audio output
Page 139 and 140: Global Presets Page You can save an
Page 141 and 142: ACT LAN LINK RESET 50-60Hz -A MAX I
Page 143 and 144: Using the Button-Label Generator so
Page 145 and 146: XTP CrossPoint 1600 and 3200 Switch
Page 147 and 148: Pinging to Determine the Extron IP
Page 149 and 150: 6. After verifying that the IP addr
Page 151: Help For Telnet command definitions
show all

Extron XTP CrossPoint 1600 and 3200 ... - Extron Electronics

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?