Extron XTP CrossPoint 1600 and 3200 ... - Extron Electronics

More documents

Recommendations

Info

Output boards space — Install output boards as desired in input slots 1 through 4 (XTP CrossPoint 1600) or input slots 1 through 8 (XTP CrossPoint 3200) and make connections. See Installing the Input or Output Board or Blank Panel on page 136 and the individual board descriptions below. NOTE: Install blank panels in unused locations to ensure proper ventilation. XTP CP 4o (XTP Output board) — See figure 8. 2a 2c 2a 2c 2a 2c 2a 2c OUT SIG LINK PWR XTP ACT LAN LINK SIG LINK PWR XTP ACT LAN LINK SIG LINK PWR XTP ACT LAN LINK SIG LINK PWR XTP ACT LAN LINK IR/RS-232 OVER XTP RS-232 IR RS-232 IR RS-232 IR RS-232 IR Tx Rx G Tx Rx Tx Rx G Tx Rx Tx Rx G Tx Rx Tx Rx G Tx Rx OUT XTP CP 4o 2b 2b 2b 2b 2d Figure 8. XTP Output Board Connectors and Indicators ATTENTION: The XTP output board can provide PoX to connected devices. PoX is intended for indoors use only. No part of a network that uses PoX can be routed outdoors. NOTE: PoX must be enabled using: • SIS commands (see the applicable XTP Power SIS commands on page 85) • Built-in HMTL pages (see XTP Power Page, on page 132) • The XTP System Configuration software (see the XTP System Configuration Software Guide, available at www.extron.com) 2a XTP output connectors — Connect a TP cable between this connector and a compatible Extron XTP receiver. See TP connectors on page 16 to wire the connector. 2b XTP Power indicators — Lights to indicate that the output board is providing power over internet (PoX) to the receiver connected to this RJ-45 connector. 2c LAN (Ethernet) connectors — As desired, connect a TP cable between a host device or control LAN and this connector for passive extension to the LAN (Ethernet) connector on the connected endpoint. See TP connectors on page 16 to wire the connector. 2d IR/RS-232 Over XTP Connectors — If desired, connect serial RS-232 signals, modulated IR signals, or both to these 3.5 mm, 5-pole captive screw connectors for bidirectional RS-232 and IR communications on the associated outputs. See RS-232 and IR connectors on page 18 to wire the connectors. XTP CrossPoint 1600 and 3200 Switchers • Installation 14
XTP CP 4o HDMI (HDMI Output board) — See figure 9. OUT AUDIO XTP CP 4o HDMI L R L R L R L R OUT 2e 2e 2e 2e 2f Figure 9. HDMI Output Board Connectors 2e Input connector — Connect an HDMI cable between this port and an HDMI video display. See HDMI connectors on page 18 for pin assignments and to use the LockIt HDMI Cable Lacing Bracket to secure the connector to the transmitter. 2f Audio Outputs (analog audio) connectors — Connect audio devices such as an audio amplifier or powered speakers, to these 3.5 mm, 5-pole captive screw connectors. These connectors output unamplified, level audio, whether it is tied from an analog analog input or de-embedded from a digital input. See Analog audio output connectors on page 21 to wire the connectors. XTP CP 4o DVI Pro (DVI Pro Output board) — See figure 10. OUT AUDIO L R L R L R L R XTP CP 4o DVI Pro OUT 2g 2g 2g 2g 2h Figure 10. DVI Pro Output Board Connectors NOTE: Although the DVI Pro boards use DVI-I connectors, the switchers handle only DVI-D (digital) video. 2g Input connector — Connect a DVI cable between this port and an DVI video display. See DVI connectors on page 19 for pin assignments. 2h Audio Outputs (analog audio) connectors — Connect audio devices such as an audio amplifier or powered speakers, to these 3.5 mm, 5-pole captive screw connectors. These connectors output unamplified, level audio, whether it is tied from an analog analog input or de-embedded from a digital input. See Analog audio output connectors on page 21 to wire the connectors. XTP CP 4o SA (Analog Audio Output board) — See figure 11. OUT AUDIO L R L R L R L R XTP CP 4o SA OUT 2i Figure 11. Analog Audio Board Connectors 2i Audio Outputs (analog audio) connectors — Connect audio devices such as an audio amplifier or powered speakers, to these 3.5 mm, 5-pole captive screw connectors. These connectors output unamplified, level audio, whether it is tied from an analog analog input or de-embedded from a digital input. See Analog audio output connectors on page 21 to wire the connectors. XTP CrossPoint 1600 and 3200 Switchers • Installation 15
Page 1 and 2: User Guide Matrix Switchers XTP Cro
Page 3 and 4: Conventions Used in this Guide Noti
Page 5 and 6: Contents Introduction..............
Page 7 and 8: IR STANDBY/ON CONFIG CHANNEL SDTV E
Page 9 and 10: The matrix switchers can be remotel
Page 11 and 12: HDMI and DVI Pro input and output b
Page 13 and 14: HDMI 1.3 compatible — Supports HD
Page 15 and 16: Installation This sections details
Page 17 and 18: LAN RS 232/RS422 1 2 REMOTE 3 4 ACT
Page 19: 1d IR/RS-232 Over XTP Connectors
Page 23 and 24: XTP board XTP ports — The XTP inp
Page 25 and 26: Use the LockIt Lacing Brackets, sup
Page 27 and 28: The level for each analog audio inp
Page 29 and 30: Front Panel Configuration Port and
Page 31 and 32: XTP CROSSPOINT 3200 1 2 INPUTS 1 2
Page 33 and 34: Control Buttons Primary functions N
Page 35 and 36: I/O Controls NOTE: See Front Panel
Page 37 and 38: Definitions The following Extron ma
Page 39 and 40: Example 1: Create a set of video an
Page 41 and 42: The current configuration (see figu
Page 43 and 44: Viewing the Configuration The curre
Page 45 and 46: 5. Deselect video: Press and releas
Page 47 and 48: Example 5: Saving a preset In the f
Page 49 and 50: Muting and Unmuting Video and Audio
Page 51 and 52: INPUTS OUTPUTS CONFIG PRIMARY 1 2 R
Page 53 and 54: Table 4. XTP CrossPoint 3200 Audio
Page 55 and 56: Example 8: Viewing and adjusting an
Page 57 and 58: Viewing and Adjusting the Analog Ou
Page 59 and 60: Table 6. Audio Volume Display Highe
Page 61 and 62: 4. Change the volume: Press and rel
Page 63 and 64: Selecting Lock mode 2 or toggling b
Page 65 and 66: 3. Change a value: Press and releas
Page 67 and 68: Performing a Hard Reset (Reset 1) T
Page 69 and 70: Optimizing the Analog Audio Trouble
Page 71 and 72:
Worksheet Example 2: Daily Configur
Page 73 and 74:
XTP CrossPoint 3200 Switchers Confi
Page 75 and 76:
Programming Guide The XTP CrossPoin
Page 77 and 78:
Establishing a Connection Establish
Page 79 and 80:
Outnn•Volxx] The switcher initiat
Page 81 and 82:
Table 8. SIS Command vs. Switcher o
Page 83 and 84:
Symbol definitions ] = Carriage ret
Page 85 and 86:
SIS Command and Response Table for
Page 87 and 88:
Table 10. EDID Values X$ Source or
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
X7( = Port number 01 = Remote RS-23
Page 117 and 118:
HTML Operation The XTP CrossPoint M
Page 119 and 120:
Status Tab System Status Page The S
Page 121 and 122:
HDCP Page The HDCP page (see figure
Page 123 and 124:
Unit Name field The Unit Name field
Page 125 and 126:
Passwords Page Access the Passwords
Page 127 and 128:
Setting up SMTP authorization If de
Page 129 and 130:
2. Click the Firmware link. 3. Sele
Page 131 and 132:
File Management Tab File Management
Page 133 and 134:
NOTES: • If you lose track of the
Page 135 and 136:
Output Adjustments Page The Output
Page 137 and 138:
Muting and unmuting an audio output
Page 139 and 140:
Global Presets Page You can save an
Page 141 and 142:
ACT LAN LINK RESET 50-60Hz -A MAX I
Page 143 and 144:
Using the Button-Label Generator so
Page 145 and 146:
XTP CrossPoint 1600 and 3200 Switch
Page 147 and 148:
Pinging to Determine the Extron IP
Page 149 and 150:
6. After verifying that the IP addr
Page 151 and 152:
Help For Telnet command definitions
Page 153:
Extron Warranty Extron Electronics
show all

Extron XTP CrossPoint 1600 and 3200 ... - Extron Electronics

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?