07.07.2014 Views

MX-M264N/M314N/M354N Operation-Manual GB

MX-M264N/M314N/M354N Operation-Manual GB

MX-M264N/M314N/M354N Operation-Manual GB

SHOW MORE
SHOW LESS

You also want an ePaper? Increase the reach of your titles

YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.

SYSTEM SETTINGS<br />

Network Settings<br />

Network settings are described below. Touch the [Network Settings] key to configure the settings.<br />

When settings are changed, the changes will take effect after the machine is restarted. To restart the machine see<br />

"TURNING THE POWER ON AND OFF" (page 1-14) in "1. BEFORE USING THE MACHINE ".<br />

IPv4 Settings<br />

When using the machine on a TCP/IP (IPv4) network, use<br />

this setting to configure the IP address of the machine.<br />

The settings are shown below.<br />

IP Address<br />

Enter the IP address of the machine.<br />

IP Subnet Mask<br />

Entry the IP Subnet Mask.<br />

IP Gateway<br />

Enter the IP Gateway address.<br />

DHCP<br />

Use this setting to have the IP address obtained<br />

automatically using DHCP (Dynamic Host Configuration<br />

Protocol). When this setting is enabled, it is not<br />

necessary to manually enter an IP address.<br />

• If the machine will be used on a TCP/IP network, be<br />

sure to enable "Enable TCP/IP" below.<br />

• If DHCP is used, the IP address assigned to the<br />

machine may change automatically. If the IP<br />

address changes, printing will not be possible.<br />

IPv6 Settings<br />

When using the machine on a TCP/IP (IPv6) network, use<br />

this setting to configure the IP address of the machine.<br />

The settings are shown below.<br />

Enable IPv6 Protocol<br />

Enable this setting.<br />

DHCPv6<br />

Use this setting to have the IP address obtained<br />

automatically using DHCP (Dynamic Host Configuration<br />

Protocol). When this setting is enabled, it is not<br />

necessary to manually enter an IP address.<br />

<strong>Manual</strong> Address<br />

Enter the IP address of the machine.<br />

Prefix Length<br />

Enter the prefix length (0 to 128).<br />

Default Gateway<br />

Enter the IP Gateway address.<br />

• If the machine will be used on a TCP/IP network, be<br />

sure to enable "Enable TCP/IP" below.<br />

• If DHCP is used, the IP address assigned to the<br />

machine may change automatically. If the IP<br />

address changes, printing will not be possible.<br />

• In an IPv6 environment, the machine can use LPD<br />

or IPP protocol.<br />

Enable TCP/IP<br />

To use the machine on a TCP/IP network, this setting<br />

must be enabled.<br />

Enable NetWare<br />

To use the machine on a NetWare network, this setting<br />

must be enabled.<br />

Enable EtherTalk<br />

To use the machine on an EtherTalk network, this<br />

setting must be enabled.<br />

Enable NetBEUI<br />

To use the machine on a NetBEUI network, this setting<br />

must be enabled.<br />

Reset the NIC<br />

This returns all "Network Settings" to the factory default<br />

settings.<br />

Ping Command<br />

Use this function to check if the machine can<br />

communicate with a computer on the network.<br />

Specify the IP address of the desired computer and<br />

touch the [Execute] key. A message will appear<br />

indicating whether or not the computer responded.<br />

7-73<br />

Contents

Hooray! Your file is uploaded and ready to be published.

Saved successfully!

Ooh no, something went wrong!