Infortrend RAID Controller Manual

More documents

Recommendations

Info

Appendix A LCD Keypad Navigation Map Key Start LCD display text Task to be performed, or the task to be performed for the configuration to take effect (red text) Press ENT on one menu item to access multiple options SR2000 v3.12K No Host LUN After selecting the option, press ESC or ENT to move on to the next item Move on to the next menu screen or option by pressing ENT or ESC Optional approach to the same task Press ENT for multiple options Set TDRV=* with NRAID RAID 0 RAID 1 RAID 1 + Spare RAID 3 Press 2 Seconds for Main Menu Press Up arrow key Press Down arrow key NOTE : Usually, pressing ENT will confirm your selection or lead you to more options. Pressing ESC will cancel a notification message or end the current option. LG=* Initialize Completed Mapped to first available Host LUN Automatically RADI 3 + Spare RAID 5 RAID 5+Spare Quick Logical Drive Install ↕ Error: Logical Navigation Map A-1 Drive Exists ! MaxSiz= **** MB SetTo ****MB? C=* I =* **** MB NEW DRV Vendor ID Maximum Drive Capacity.. Spare Drive Assignments.. Logical Drive Assignments.. TDRV=7 Create LG Level= * ? NRAID RAID 0 RAID 1 RAID 3 RAID 5 Create LG=* Initialize Completed Init Parity **% Please Wait ! Create Logical Drive ? Change Logical Drive Parameter? TDRV=* Create LG Level=RAID * ? C =* I =* **** MB NEW DRV Vendor ID Select Physical Drive Redund Ctlr LG Assign Sec Ctlr ? LG=0 Not Defined ? View and Edit Logical Drives ↕ Disk Reserved Space.. Available Physical Drive(s) RAID * Selected To select drives ChangeSize: ** MB SetTo ** MB Member Drive Status C =* I =* ****MB LG=* LN Vendor ID Scroll to select an undefined Logical Drive number LG=0 ~LG=7 Delete Logical Drive ? View SCSI Drives.. to next partition ENT to confirm then LG=* Part=* ****MB ? Cannot Add to LV Still Partition? Delete Logical Drives.. Partition Logical Drive.. View & Edit Enter LD Name: Logical Drive Name.. Logical Drive Assignment.. LG* RAID* DRV =* **** MB GD SB=* Select a configured Logical Drive Change Setting Do Reset Ctlr ? Redund Ctlr LG Assign Sec Ctlr ? Expand Logical Drive.. LG* RAID* DRV=* ****MB GD SB =* Expanding **% Please Wait! MaxSiz= ** MB SetTor **MB? Unused Capacity on logical drive Add SCSI Drives.. Regenerate Parity.. Copy and Replace Drives.. Error: No Free Capacity ! Rebuild Logical Drive.. LG* RAID* DRV =* ****MB GD SB =* Add Drives *% Please Wait ! Select New Drive to add Capacity C =* I =* ****MB LG=* LN Vendor ID Add Drv Selected To select drives LG* RAID* DRV=* ****MB GD SB =* Regen Parity *% Please Wait ! Regenerate LD Parity ? Expand Logical Drive Drv Copying *% Please Wait ! Copy and Replace Drive ? C=* I =* **** MB NEW DRV Vendor ID Enter To Select One New Drive C=* I =* ***MB LG=* LN Vendor ID Enter To Select a On-Line Drive Rebuild Progress .. LG* RAID* DRV =* **** MB RB SB=* Rebuilding **% Please Wait! Rebuild Logical Drive ?
A-2 Create Create Logical Volume Successed Create Logical Volume ? Red Ctlr Assign to Sec. Ctlr ? Logical Volume Assignments .. Change Logical Volume Params ? LG* RAID* DRV =* ****MB GD SB=* LV=* Selected To Select LD Drives LV=* Not Defined ? Scroll to select an undefined Logical Volume number LV=0 ~ LV=7 View and Edit Logical Volume ↕ Create Logical Volume ? LG* RAID* DRV =* ****MD GD SB=* Delete Logical Volume ? View Logical Drives.. View & Edit ENT to confirm then to next partition LV=* Part=*: ****MB ? Delete Logical Volume.. Partition Logical Volume.. Logical Volume Assignment.. Expand Logical Volume.. Modify Existing Logical Volume Secondary controller ID must be available Change Setting Do Reset Ctlr ? Red Ctlr Assign to Sec. Ctlr ? LV* ID=* ****MB DRV=* MaxSiz = **MB Set To **MB? Expand member Logical Drive First Logical Drive No Free Capacity ! Map to Logical Drive ? Logical Volume ? Physical SCSI Drive ? Map Pri. Ctlr CH= * ID= * ? Map Pri/Sec. Ctlr CH=* ID =* ? CH* ID** LUN* Mapto LV/LD PRT* ? Map Host LUN ↓ LV/LD=* PART=* ****MB ? Map Host LUN ? CH* ID* LUN* Not Mapped Host Channel and ID Selection View and Edit Host Channel Selection ID Selection Map Sec. Ctlr CH= * ID= * ? Host LUNs ↕ Partition Selection LUN Selection Edit Existing LUN Mapping Reset Controller Primary / Secondary Controller ? Add Channel SCSI ID .. Set SCSI Channel ID .. View and Edit SCSI Channels ↕ Delete CH* ID* LUN= * Mapping? CH* ID ** LUN* Mapto LV/LD* PRT* Select a Host Channel ID View Host Filter Information .. Host ID - ************ View and Edit Host Filtering.. CH* ID* LUN* Multi LV/LD Map Add from Current Device Lists .. Host ID - **************** Add Host Filter Entry ? Edit Host Filter Parameter ↑ Manual Add Host Filter Entry .. Enter HBA port name and Mask value Logical Volume * ↓ Partition * Host ID - ↕ **************** Host ID Mask - ↕ **************** Filter Type - ↕ Include/Exclude Access Mode - � Read/Write - Read Only Add Host Filter Entry .. Delete Host LUN .. Delete Host Filter Entry .. Infortrend
Page 1 and 2:
Infortrend External RAID Controller
Page 3 and 4:
UNIX is a registered trademark of T
Page 5 and 6:
Chapter 5 LCD Screen Messages 5.1 T
Page 7 and 8:
Logical Drive Information..........
Page 9 and 10:
13.9.1 Supported Operating Systems
Page 11 and 12:
Chapter 8 Figure 8 - 1 Drive Space
Page 13 and 14:
Chapter 13 details how to install t
Page 15 and 16:
Functional Table of Contents: This
Page 17 and 18:
Chapter 9 Fibre Operation Page numb
Page 19 and 20:
Chapter 14 Fault-Bus Page number: L
Page 21 and 22:
Chapter 2 1 2 3 Logical Drive Funct
Page 23 and 24:
Figure 2 - 2 NRAID = + + + Logical
Page 25 and 26:
Figure 2 - 7 RAID 3 Logical Drive P
Page 27 and 28:
Local Spare Drive LS (9GB) 1 2 (9GB
Page 29 and 30:
2.4.3 Automatic Rebuild and Manual
Page 31 and 32:
2.5 Logical Volume (Multi-Level RAI
Page 33 and 34:
Configuration A is a large logical
Page 35 and 36:
To perform RAID expansion on a logi
Page 37 and 38:
Chapter 3 RAID Planning 3.1 Conside
Page 39 and 40:
Spare drives allow for the unattend
Page 41 and 42:
3.3.2 Understanding Step by Step Fi
Page 43 and 44:
following chapters. The configurati
Page 45 and 46:
3. Create and configure one or more
Page 47 and 48:
4-2 Select "Communication Parameter
Page 49 and 50:
4-4 4.2 Out-of-Band via Ethernet Ne
Page 51 and 52:
4-6 • One logical drive with rese
Page 53 and 54:
5-2 5.3 Logical Drive Status Logica
Page 55 and 56:
5-4 5.5 SCSI Drive Status SCSI Chan
Page 57 and 58:
5-6 5.7 Controller Voltage and Temp
Page 59 and 60:
Chapter 6 Front Panel Operation 6.1
Page 61 and 62:
Write-Back/Write-Through Cache Enab
Page 63 and 64:
You may first examine whether there
Page 65 and 66:
Maximum Drive Capacity: Choose “M
Page 67 and 68:
6.6 Partitioning a Logical Drive/Lo
Page 69 and 70:
With any of the Host LUN mapped, th
Page 71 and 72:
NOTE: • The different levels of r
Page 73 and 74:
Assigning a Logical Drive Name Pres
Page 75 and 76:
6.10 Viewing and Editing Host LUNs
Page 77 and 78:
press ENT. Press ▼ or ▲ to choo
Page 79 and 80:
SCSI channel information will be di
Page 81 and 82:
Setting a SCSI Channel’s Terminat
Page 83 and 84:
Press ▼ or ▲ to select “Set T
Page 85 and 86:
Press ENT for two seconds to change
Page 87 and 88:
Reset Controller To reset the contr
Page 89 and 90:
Controller Unique Identifier Choose
Page 91 and 92:
Chapter 7 Terminal Screen Messages
Page 93 and 94:
7.4 Logical Drive Status LG LV ID R
Page 95 and 96:
7.6 SCSI Drive’s Status Slot Chl
Page 97 and 98:
On Terminator is enabled. Off Termi
Page 99 and 100:
7.9 Viewing Event Logs on the Scree
Page 101 and 102:
8-2 mode is to backup all data to s
Page 103 and 104:
8-4 IMPORTANT! • The default opti
Page 105 and 106:
8-6 Logical Drive Preferences: Afte
Page 107 and 108:
8-8 8.5 Creating a Logical Volume A
Page 109 and 110:
8-10 Choose the logical volume you
Page 111 and 112:
8-12 select an available LUN (one n
Page 113 and 114:
8-14 Move cursor bar to the SCSI dr
Page 115 and 116:
8-16 Choose the logical drive you w
Page 117 and 118:
8-18 8.10 Viewing and Editing Host
Page 119 and 120:
8-20 You may also choose “flash s
Page 121 and 122:
8-22 Viewing and Editing SCSI IDs /
Page 123 and 124:
8-24 Setting a Secondary Controller
Page 125 and 126:
8-26 IMPORTANT! • Every time you
Page 127 and 128:
8-28 Disconnecting Support Choose
Page 129 and 130:
8-30 Change Password Use the contro
Page 131 and 132:
8-32 For "Controller Maintenance" f
Page 133 and 134:
8-34 Saving NVRAM to File (via Text
Page 135 and 136:
8-36 Choose “View and Edit Periph
Page 137 and 138:
8-38 SCSI Drive Read/Write Test Fro
Page 139 and 140:
9-2 Different Fibre arrays can be d
Page 141 and 142:
9-4 issue when every server in this
Page 143 and 144:
9-6 Figure 9 - 1 Host Loop Connecti
Page 145 and 146:
9-8 9.4 Configuration: Host and Dri
Page 147 and 148:
9-10 View and Edit Fibre Drive Choo
Page 149 and 150:
9-12 Figure 9 - 3 Dual Loop Configu
Page 151 and 152:
9-14 With firmware release 3.14 and
Page 153 and 154:
9-16 Figure 9 - 5 Host-LUN Mapping
Page 155 and 156:
9-18 When a logical unit is selecte
Page 157 and 158:
9-20 Include: If a node's (a workst
Page 159 and 160:
9-22 The exemplary entry list is sh
Page 161 and 162:
10-2 Figure 10 - 1 Logical Drive Ex
Page 163 and 164:
10-4 A list of available drives wil
Page 165 and 166:
10-6 10.1.3 Copy and Replace Drives
Page 167 and 168:
10-8 10.1.4 Expand Logical Drive In
Page 169 and 170:
10-10 10.1.6 Example: RAID Expansio
Page 171 and 172:
10-12 Follow the steps described in
Page 173 and 174:
10-14 Select an existing volume (Di
Page 175 and 176:
10-16 Drive E: now has a capacity r
Page 177 and 178:
10-18 The cloning process will begi
Page 179 and 180:
10-20 The cloning progress will be
Page 181 and 182:
10-22 NOTE: Clone + Replace: Contro
Page 183 and 184:
10-24 How to Utilize the S.M.A.R.T.
Page 185 and 186:
A SCSI channel (SCSI bus) can conne
Page 187 and 188:
10-28 This controller supports the
Page 189 and 190:
10-30 Table 10 - 1 Peripheral Devic
Page 191 and 192:
10-32 10.3.2 Drive-side Parameters:
Page 193 and 194:
10-34 When the drive itself detects
Page 195 and 196:
10-36 Edit SCSI Drives.” If any d
Page 197 and 198:
10-38 To decide under what conditio
Page 199 and 200:
11-2 Partition Information LG Parti
Page 201 and 202:
11-4 11.3 View and Edit Host LUN’
Page 203 and 204:
11-6 11.4 View and Edit SCSI Drives
Page 205 and 206:
11-8 11.6 View and Edit Configurati
Page 207 and 208:
11-10 Disk Array Parameters Rebuild
Page 209 and 210:
11-12 Update Firmware 11.8 Save NVR
Page 211 and 212:
12-2 � Fibre Interface The contro
Page 213 and 214:
12-4 Figure 12 - 4 Partitioning Log
Page 215 and 216:
12-6 in this configuration should f
Page 217 and 218:
12-8 interface and multiple IDs are
Page 219 and 220:
12-10 F. Considerations with Redund
Page 221 and 222:
12-12 Controller Settings: Redundan
Page 223 and 224:
12-14 12.2.2 Limitations • Both c
Page 225 and 226:
12-16 12.3 Configuration Listed bel
Page 227 and 228:
12-18 When the redundant controller
Page 229 and 230:
12-20 The process of creating Prima
Page 231 and 232: 12-22 NOTE: Front Panel View of Con
Page 233 and 234: 12-24 The message "Enable Redundant
Page 235 and 236: 12-26 Creating Primary and Secondar
Page 237 and 238: 12-28 Select partition Mapping opti
Page 239 and 240: 12-30 If the replacement has been i
Page 241 and 242: Chapter 13 In-band SCSI Text RAID M
Page 243 and 244: 13.2 Windows NT for DEC Alpha Intro
Page 245 and 246: NOTE: • The names and values in t
Page 247 and 248: 13.3 MS-DOS Introduction: The Drive
Page 249 and 250: (where "filename" is the filename o
Page 251 and 252: 13.5.3 Install SNMP Extension Agent
Page 253 and 254: To uncompress the compressed file,
Page 255 and 256: 5. Reboot the system. 6. Run the Te
Page 257 and 258: 13.7 Solaris 2.5.x/2.6/7/8 for SPAR
Page 259 and 260: Select package(s) you will to proce
Page 261 and 262: (where "filename" is the filename o
Page 263 and 264: 13.9 SCO UnixWare Introduction: The
Page 265 and 266: the corresponded Peripheral Device
Page 267 and 268: • SNMP MIB file ("RAIDSNMP.MIB")
Page 269 and 270: NOTE: 11. Type "Pathname" for value
Page 271 and 272: Chapter 14 Fault-Bus 14.1 What is F
Page 273 and 274: failure, activate the signal. When
Page 275 and 276: information list. Assign a slot num
Page 277 and 278: Press ▼ or ▲ to select “Toggl
Page 279 and 280: Delete the Slot Number of a SCSI Dr
Page 281: Viewing the Status of Each Fault-bu
Page 285 and 286: A-4 Change Setting Do Reset Ctlr ?
Page 287 and 288: A-6 Enable/Disable Motor Spin-Up ?
Page 289 and 290: Appendix B Basic RAID Management: F
Page 291 and 292: Maximum concurrent Host LUN connect
Page 293 and 294: Drive S.M.A.R.T. Support Supported,
Page 295 and 296: Data Safety: Redundant Controller f
Page 297 and 298: User Interface: RAIDWatch on-board
Page 299 and 300: C-2 The rolling upgrade is automati
Page 301 and 302: C-4 Upgrade the Firmware Binary Onl
Page 303 and 304: C-6 2. Go to "Controller Maintenanc
Page 305 and 306: D-2 Drive SCSI Channel/Drive Error
Page 307 and 308: Controller Event 2-Line LCD DRAM Pa
Page 309 and 310: 2-Line LCD Controller Init Complete
Page 311 and 312: Drive SCSI Channel/Drive Error 2-Li
Page 313 and 314: 2-Line LCD C=_ I=_ Drive Not Ready
Page 315 and 316: 2-Line LCD CHL=_ SCSI Channel Failu
Page 317 and 318: 2-Line LCD Mem is Now Enough Suppor
Page 319 and 320: 2-Line LCD LG=_ Expansion Completed
Page 321 and 322: 2-Line LCD LG=_ Add SCSI Drive Comp
Page 323 and 324: 2-Line LCD High +12V Voltage Detect
Page 325 and 326: 2-Line LCD High +5V Voltage Detecte
Page 327 and 328: Appendix E Differences in Logical D
Page 329 and 330: You may also see the status of rese
Page 331 and 332: D Dedicated Communications Loops 9-
Page 333 and 334:
port) Out-of-band Configuration, Re
Page 335:
target/drive channel, viewing and 6
show all

Infortrend RAID Controller Manual

Create successful ePaper yourself

Delete template?

Save as template?