running machine - H-P-COSMOS Sports and Medical

More documents

Recommendations

Info

[8.A2] OP20 RS232 interface protocol: COM 1 Various ECG and Ergospirometry systems support the h/p/cosmos coscom protocol. Individual adaptation of protocol on request. For further information about the h/p/cosmos coscom protocol see www.coscom.org We recommend to use the h/p/cosmos coscom protocol, as it provides a high safety and functionality standard. h/p/cosmos para control ® and h/p/cosmos para graphics ® exclusively work with the h/p/cosmos coscom protocol. For advanced h/p/cosmos coscom v3 connections with Baudrate 115200 please select OP20=20 . Please note that the connected peripherie/software must be approved for h/p/cosmos coscom v3 with Baudrate 115200 (for example h/p/cosmos para control 4.0). OP21 RS232 interface protocol: COM 2 file: n:\article\cos14310m5-v1_06hpc-en\20120215_cos14310m5-v1.06hpc-en_manual_h-p-cosmos_running_machine.doc © 2012 h/p/cosmos sports & medical gmbh email@h-p-cosmos.com created 15.02.2012 printed 15.02.2012 page: 102 of 213 optional settings § indicates flashing: number of the RS232 interface protocol $ and % reports: OFF = RS232 not active / no protocol / interface deactivated 1 = h/p/cosmos coscom v1, v2, v3 with Baudrate 9600 bps ( standard setting COM 1 and COM 2) 2 = JAEGER OXYCON (up to 1995); if available use: h/p/cosmos coscom (= 1) 3 = Printer protocol (serial printer or converter required) 4 = Free 5 = Pacer treadmill emulation (max. 12.7 km/h) 6 = MAX 1 (GE Marquette) EKG; if available use: h/p/cosmos coscom (= 1) 7 = Trackmaster treadmill emulation in km/h 8 = Trackmaster treadmill emulation in miles per hour 9 = custo card ECG (MS DOS-Version); if available use: h/p/cosmos coscom (= 1) 10 = Loop Back Test (special test plug required, available at h/p/cosmos) 11 = SunTech Tango blood pressure monitor 12 = Remote Control Hardware Terminal MCU 4 (special hardware required) 13 = Burdick T 500 treadmill emulation 14 = Burdick T 600 treadmill emulation 17 = Chipcard reader Ergofit (special hardware required) – only available at MCU4 (all firmware versions) or MCU5 firmware < v1.03.x 18 = Chipcard reader Proxomed (special hardware required) – only available at MCU4 (all firmware versions) or MCU5 firmware < v1.03.x 20 = h/p/cosmos coscom v3 with Baudrate 115200 bps See descriptions above OP23 RS232 interface protocol COM 4 § indicates flashing: number of the RS232 interface protocol $ and % reports: OFF = RS232 not active / no protocol / interface deactivated 18 = Chip-card reader PROXOMED (special hardware required) 20 = h/p/cosmos coscom v3 / Baudrate 115200 bps 22 = Polar W:I:N:D: - System (weitere Einstellungen in Benutzer Option OP19 und Administrator Option OP16)
[8.A2] OP27 Minimum acceleration and deceleration level The selected minimum level is valid for all acceleration and deceleration processes in all modes and profiles. OP28 Maximum acceleration and deceleration level The selected maximum level is valid for all acceleration and deceleration processes in all modes and profiles file: n:\article\cos14310m5-v1_06hpc-en\20120215_cos14310m5-v1.06hpc-en_manual_h-p-cosmos_running_machine.doc © 2012 h/p/cosmos sports & medical gmbh email@h-p-cosmos.com created 15.02.2012 printed 15.02.2012 page: 103 of 213 optional settings § blinking, reports the min. acceleration / deceleration for all modes and profiles (standard: level 1) Level of settings: 1 ... 5 but not higher than the value in option 28. Due to safety reasons, the acceleration / deceleration levels 5, 6 and 7 can not be selected. Note: The selected acceleration and deceleration level is NOT valid for control and operation via RS232-interface. In this case the acceleration and deceleration level is set in option no. 29 resp. set in the corresponding command of the h/p/cosmos coscom protocol. § blinking, reports the max. acceleration / deceleration for all modes and profiles (standard: level 4) Note: Due to safety reasons, the acceleration / deceleration levels 5, 6 and 7 can only be selected, if the safety of the subject is provided for by the use of the respective fall prevention (e. g. by the safety arch). The maximum acceleration and deceleration level is NOT valid for control and operation via V24/RS232 interface. In this case the acceleration and deceleration level is set in option no. 29 resp. set in the corresponding command of the h/p/cosmos coscom protocol. OP29 Standard- Acceleration and deceleration The selected acceleration and deceleration level is valid for control and level for RS 232 interface operation via RS232 interface. This option is very helpful, if the peripheral equipment (e.g. ECG, Ergospirometry, PC) does not offer a menu for acceleration and deceleration levels. § blinking, reports: 1 ... 5, (Standard: 1) for the acceleration and deceleration level for all speed commands via RS 232. The maximum value adjustable depends on the setting of option 28. Note: If the peripheral equipment sends an acceleration and deceleration command via the h/p/cosmos coscom protocol, the selected level in option number 29 is not valid for these speed commands. OP40 Locking and unlocking of the treadmill OFF = After switching on, the treadmill is completely locked / not accessible. To unlock the treadmill, press the buttons +, - and START together at the same time. While locked the display shows "no ACCESS" ON = treadmill is unlocked / accessible (standard) OP41 Locking and unlocking the manual mode OFF = manual mode is locked / not accessible ON = manual mode is unlocked / accessible (standard) OP42 Locking and unlocking the profile mode OFF = profile mode is locked / not accessible 1 ... 6 = profile mode is unlocked / accessible up to the selected profile number Standard: 6 Example: selected profile number = 3: The profiles 1-3 can be selected, the profiles 4 – 6 can not be selected OP43 Locking and unlocking the cardio mode OFF = cardio mode is locked / not accessible ON = cardio mode is unlocked (standard)
Page 1 and 2:
Operating instructions and service
Page 3 and 4:
Dear customer, We would like to exp
Page 5 and 6:
h/p/cosmos saturn 300/125r h/p/cosm
Page 7 and 8:
file: n:\article\cos14310m5-v1_06hp
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
[3.D] Materials used file: n:\artic
Page 15 and 16:
[3.I] Specific safety or performanc
Page 17 and 18:
[4.]Safety, warnings, precautions,
Page 19 and 20:
Safety Stop = Emergency Stop Extern
Page 21 and 22:
[4.D] General Instructions / Safety
Page 23 and 24:
[4.E4] Connection of units installe
Page 25 and 26:
[4.F] Medical device software safet
Page 27 and 28:
[4.H] Programmable, electrical medi
Page 29 and 30:
safety, warnings, precautions, proh
Page 31 and 32:
Picture 11: classification of a net
Page 33 and 34:
Summary: safety, warnings, precauti
Page 35 and 36:
safety, warnings, precautions, proh
Page 37 and 38:
Some examples for safety features a
Page 39 and 40:
[5.]Application, Indication, Contra
Page 41 and 42:
application, indication, contra-ind
Page 43 and 44:
application, indication, contra-ind
Page 45 and 46:
[6.]Installation & commissioning [6
Page 47 and 48:
[6.A2] Transport with trolleys For
Page 49 and 50:
[6.C] Electrical installation insta
Page 51 and 52: [6.C2] Electric safety measurements
Page 53 and 54: N Devices with MCU4 control unit (u
Page 55 and 56: Picture top: MCU5-control-board and
Page 57 and 58: installation & commissioning Device
Page 59 and 60: [6.F] Installation, Overview, Check
Page 61 and 62: [7.]Operation [7.A] UserTerminal, k
Page 63 and 64: The indicated values remain, after
Page 65 and 66: [7.B3] Manual mode Initiation: Runn
Page 67 and 68: Initiation: Running-Belt is not mov
Page 69 and 70: [7.B7] Profile outline file: n:\art
Page 71 and 72: [7.B7] profile 5 file: n:\article\c
Page 73 and 74: file: n:\article\cos14310m5-v1_06hp
Page 75 and 76: [7.B10] [06] Confirm personal age [
Page 77 and 78: [7.B12] Test mode and free program
Page 79 and 80: [7.B13] 4 Bruce protocol e.g. for E
Page 81 and 82: [7.B13] 11 The „Gardner Testproto
Page 83 and 84: [7.B13] 74 Training Interval 300 ..
Page 87 and 88: [7.B13] 92 Test profile file: n:\ar
Page 89 and 90: [7.B13] 94 Test profile file: n:\ar
Page 91 and 92: The test-result is the index-value
Page 93 and 94: [7.B16] [13] 2000 meter walking. Wa
Page 95 and 96: [7.B17] [19] Confirm time [20] Conf
Page 97 and 98: [7.B18] Possibilities of interferin
Page 99 and 100: [8.A2] List of user options / optio
Page 101: file: n:\article\cos14310m5-v1_06hp
Page 105 and 106: [8.A3] Standard settings for the us
Page 107 and 108: [8.B1] OP04 Maximum speed for rever
Page 113 and 114: [8.B1] OP39 Elevation: display as s
Page 115 and 116: [8.B1] OP49 Type of frequency inver
Page 119 and 120: [8.B2] Standard settings of adminis
Page 121 and 122: [8.B3] List of running machines typ
Page 123 and 124: [9.B] Immediate maintenance mainten
Page 125 and 126: [9.C4] Equivalent (alternative) lea
Page 127 and 128: maintenance & safety inspections In
Page 129 and 130: [9.D2] Lubricant test maintenance &
Page 131 and 132: [9.D4] Devices with UserTerminal &
Page 133 and 134: maintenance & safety inspections Re
Page 135 and 136: maintenance & safety inspections Pr
Page 137 and 138: maintenance & safety inspections N
Page 139 and 140: Medium to achieve hygienic safety:
Page 141 and 142: [9.L] Spare parts & consumables mai
Page 143 and 144: [10.]Trouble shooting file: n:\arti
Page 145 and 146: [10.E] Voltage at the device housin
Page 147 and 148: [10.I] Error messages / Error codes
Page 151 and 152: [10.I1] E51 Error of frequency inve
Page 153 and 154:
[10.I2] Devices without UserTermina
Page 155 and 156:
Dimension of running surface length
Page 157 and 158:
Dimension of running surface length
Page 159 and 160:
Dimension frame length x width x he
Page 161 and 162:
Page 163 and 164:
[11.E1] Interface additional inform
Page 165 and 166:
[12.]Accessories and options file:
Page 167 and 168:
[12.B] Additional keyboard and add.
Page 169 and 170:
[12.C1] Danger precaution and opera
Page 171 and 172:
[02] [03] [04] [05] file: n:\articl
Page 173 and 174:
[02] [03] Total view running machin
Page 175 and 176:
[12.G] h/p/cosmos airwalk se 135 (a
Page 177 and 178:
[12.I] h/p/cosmos robowalk ® expan
Page 179 and 180:
picture type of stop function inter
Page 181 and 182:
[12.M2] Change from forward to reve
Page 183 and 184:
[12.P] Retrofitting / additional sa
Page 185 and 186:
[12.S] Digital (serial) RS232 inter
Page 187 and 188:
[12.T] Printer protocol file: n:\ar
Page 189 and 190:
[12.U4] Battery of the transmitter
Page 191 and 192:
[12.W] PC Software h/p/cosmos para
Page 193 and 194:
[12.Y] PC Software h/p/cosmos para
Page 195 and 196:
[13.B] Certificate of the TSA (TÜV
Page 197 and 198:
[13.D] Certificate of compliance fo
Page 199 and 200:
Page 201 and 202:
[14.]Disposal file: n:\article\cos1
Page 203 and 204:
[16.]Appendix - Instruction and com
Page 205 and 206:
[06] [07] [08] [09] file: n:\articl
Page 207 and 208:
[06] [07] [16.D] Advice and support
Page 209 and 210:
[16.F] Service report - cos15531 fi
Page 211 and 212:
[16.H] Wiring diagram load circuit
Page 213:
[16.J] Wiring diagram control circu
show all

running machine - H-P-COSMOS Sports and Medical

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?