running machine - H-P-COSMOS Sports and Medical

More documents

Recommendations

Info

unning, cycling, cross-country, skating [inline, roller ski] Valve-cock position [1] horizontally: The distributor [2] is adjusted for lubrication [3] only in the center of the runningdeck [4]. The valve-cock position only changes the distribution of the oil amount to the various oil-outlets (tubes). The total oil-supply amount of the oil-pump always remains constant, independent from the valve-cock position. A nearly empty oil-tank will be indicated by the control lamp “Empty Oil-tank” at the external control unit. Refill the oiltank when control lamp indicates wheelchair Valve-cock position [1] vertically: The distributor [2] is adjusted for lubrication [3] over the entire width of the running-deck [4]. The valve-cock position only changes the distribution of the oil amount to the various oil-outlets (tubes). The total oilsupply amount of the oil-pump always remains constant, independent from the valve-cock position. A nearly empty oil-tank will be indicated by the control lamp “empty oil-tank” at the external control unit. Refill the oiltank when control lamp indicates. Additionally at standard settings the word “OIL” will flash every 1000 km at the display. If this message occurs, check the oil-level in the oiltank and refill preterm if necessary. maintenance & safety inspections The device does not have a sensor, the oil-message does not extinguish automatically. After checking the oil-level, the message has to be quit with „OPTION 01“. file: n:\article\cos14310m5-v1_06hpc-en\20120215_cos14310m5-v1.06hpc-en_manual_h-p-cosmos_running_machine.doc © 2012 h/p/cosmos sports & medical gmbh email@h-p-cosmos.com created 15.02.2012 printed 15.02.2012 page: 132 of 213
maintenance & safety inspections Refilling oil-tank N Follow this procedure to refill the oil-tank: N Unplug the device and wait for one minute. N The oil-tank is located in the external control unit of the device below at the left side (At device up to the construction year 2002 and without external control unit the oil-tank is located at the rear position of the machine close to the drive engine.). N Open the lid of the tank and refill the oil-tank with approximately 0.5 litre (at devices up to construction year 2002 and without external control unit approximately 1 to 1.5 litre) with the provided original special oil, to receive at h/p/cosmos. N Close the lid of the oil-tank. N Plug in the power plug of the device and switch device on. N Check control lamp at the external control unit. If it is not indicating anymore, the oil-tank has been correctly refilled. N If necessary quit oil-message with „OPTION 01“. Special oil for sliding plate with automatic lubrication/0.25l-bottle [cos14007] Special oil for sliding plate with automatic lubrication/0.50l-bottle [cos13438] [9.D5] Set back of oil message MCU 4 without UserTerminal An external UserTerminal or the PC-software h/p/cosmos para control ® is required for this. Further instructions see "Devices with UserTerminal”. [9.D6] Set back of oil message MCU with UserTerminal Start: Running belt is not moving. One of the mode LED � of operation is flashing: (manual, profile, cardio, test) [9.D6] Step Activity Keys Response/Display [01] Select of the mode for "user options" (OPxx) = indicates: OP01 flashing (for option no. 01) a d b ! and " indicate: E.rE SEt (for error reset) all 3 keys simultaneously for at least 3 seconds [02] Confirm option no. 1 [03] Delete message [04] Quit option mode c c b § indicates: donE to inform you, that you have to delete the oil message = indicates: OP01 flashing (for option no. 01) ! and " indicate: E.rE SEt (or error reset) Stand-by mode � manual, profil, cardio or test is flashing file: n:\article\cos14310m5-v1_06hpc-en\20120215_cos14310m5-v1.06hpc-en_manual_h-p-cosmos_running_machine.doc © 2012 h/p/cosmos sports & medical gmbh email@h-p-cosmos.com created 15.02.2012 printed 15.02.2012 page: 133 of 213
Page 1 and 2:
Operating instructions and service
Page 3 and 4:
Dear customer, We would like to exp
Page 5 and 6:
h/p/cosmos saturn 300/125r h/p/cosm
Page 7 and 8:
file: n:\article\cos14310m5-v1_06hp
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
[3.D] Materials used file: n:\artic
Page 15 and 16:
[3.I] Specific safety or performanc
Page 17 and 18:
[4.]Safety, warnings, precautions,
Page 19 and 20:
Safety Stop = Emergency Stop Extern
Page 21 and 22:
[4.D] General Instructions / Safety
Page 23 and 24:
[4.E4] Connection of units installe
Page 25 and 26:
[4.F] Medical device software safet
Page 27 and 28:
[4.H] Programmable, electrical medi
Page 29 and 30:
safety, warnings, precautions, proh
Page 31 and 32:
Picture 11: classification of a net
Page 33 and 34:
Summary: safety, warnings, precauti
Page 35 and 36:
safety, warnings, precautions, proh
Page 37 and 38:
Some examples for safety features a
Page 39 and 40:
[5.]Application, Indication, Contra
Page 41 and 42:
application, indication, contra-ind
Page 43 and 44:
application, indication, contra-ind
Page 45 and 46:
[6.]Installation & commissioning [6
Page 47 and 48:
[6.A2] Transport with trolleys For
Page 49 and 50:
[6.C] Electrical installation insta
Page 51 and 52:
[6.C2] Electric safety measurements
Page 53 and 54:
N Devices with MCU4 control unit (u
Page 55 and 56:
Picture top: MCU5-control-board and
Page 57 and 58:
installation & commissioning Device
Page 59 and 60:
[6.F] Installation, Overview, Check
Page 61 and 62:
[7.]Operation [7.A] UserTerminal, k
Page 63 and 64:
The indicated values remain, after
Page 65 and 66:
[7.B3] Manual mode Initiation: Runn
Page 67 and 68:
Initiation: Running-Belt is not mov
Page 69 and 70:
[7.B7] Profile outline file: n:\art
Page 71 and 72:
[7.B7] profile 5 file: n:\article\c
Page 73 and 74:
Page 75 and 76:
[7.B10] [06] Confirm personal age [
Page 77 and 78:
[7.B12] Test mode and free program
Page 79 and 80:
[7.B13] 4 Bruce protocol e.g. for E
Page 81 and 82: [7.B13] 11 The „Gardner Testproto
Page 83 and 84: [7.B13] 74 Training Interval 300 ..
Page 85 and 86: file: n:\article\cos14310m5-v1_06hp
Page 87 and 88: [7.B13] 92 Test profile file: n:\ar
Page 89 and 90: [7.B13] 94 Test profile file: n:\ar
Page 91 and 92: The test-result is the index-value
Page 93 and 94: [7.B16] [13] 2000 meter walking. Wa
Page 95 and 96: [7.B17] [19] Confirm time [20] Conf
Page 97 and 98: [7.B18] Possibilities of interferin
Page 99 and 100: [8.A2] List of user options / optio
Page 103 and 104: [8.A2] OP27 Minimum acceleration an
Page 105 and 106: [8.A3] Standard settings for the us
Page 107 and 108: [8.B1] OP04 Maximum speed for rever
Page 113 and 114: [8.B1] OP39 Elevation: display as s
Page 115 and 116: [8.B1] OP49 Type of frequency inver
Page 119 and 120: [8.B2] Standard settings of adminis
Page 121 and 122: [8.B3] List of running machines typ
Page 123 and 124: [9.B] Immediate maintenance mainten
Page 125 and 126: [9.C4] Equivalent (alternative) lea
Page 127 and 128: maintenance & safety inspections In
Page 129 and 130: [9.D2] Lubricant test maintenance &
Page 131: [9.D4] Devices with UserTerminal &
Page 135 and 136: maintenance & safety inspections Pr
Page 137 and 138: maintenance & safety inspections N
Page 139 and 140: Medium to achieve hygienic safety:
Page 141 and 142: [9.L] Spare parts & consumables mai
Page 143 and 144: [10.]Trouble shooting file: n:\arti
Page 145 and 146: [10.E] Voltage at the device housin
Page 147 and 148: [10.I] Error messages / Error codes
Page 151 and 152: [10.I1] E51 Error of frequency inve
Page 153 and 154: [10.I2] Devices without UserTermina
Page 155 and 156: Dimension of running surface length
Page 157 and 158: Dimension of running surface length
Page 159 and 160: Dimension frame length x width x he
Page 163 and 164: [11.E1] Interface additional inform
Page 165 and 166: [12.]Accessories and options file:
Page 167 and 168: [12.B] Additional keyboard and add.
Page 169 and 170: [12.C1] Danger precaution and opera
Page 171 and 172: [02] [03] [04] [05] file: n:\articl
Page 173 and 174: [02] [03] Total view running machin
Page 175 and 176: [12.G] h/p/cosmos airwalk se 135 (a
Page 177 and 178: [12.I] h/p/cosmos robowalk ® expan
Page 179 and 180: picture type of stop function inter
Page 181 and 182: [12.M2] Change from forward to reve
Page 183 and 184:
[12.P] Retrofitting / additional sa
Page 185 and 186:
[12.S] Digital (serial) RS232 inter
Page 187 and 188:
[12.T] Printer protocol file: n:\ar
Page 189 and 190:
[12.U4] Battery of the transmitter
Page 191 and 192:
[12.W] PC Software h/p/cosmos para
Page 193 and 194:
[12.Y] PC Software h/p/cosmos para
Page 195 and 196:
[13.B] Certificate of the TSA (TÜV
Page 197 and 198:
[13.D] Certificate of compliance fo
Page 199 and 200:
Page 201 and 202:
[14.]Disposal file: n:\article\cos1
Page 203 and 204:
[16.]Appendix - Instruction and com
Page 205 and 206:
[06] [07] [08] [09] file: n:\articl
Page 207 and 208:
[06] [07] [16.D] Advice and support
Page 209 and 210:
[16.F] Service report - cos15531 fi
Page 211 and 212:
[16.H] Wiring diagram load circuit
Page 213:
[16.J] Wiring diagram control circu
show all

running machine - H-P-COSMOS Sports and Medical

Create successful ePaper yourself

Delete template?

Save as template?