running machine - H-P-COSMOS Sports and Medical

More documents

Recommendations

Info

[7.B13] 8 Ellestad A Protokoll e.g. for ECG stress test 9 Ellestad B Protokoll e.g. for ECG stress test 10 Ramp profile (not for all models available) file: n:\article\cos14310m5-v1_06hpc-en\20120215_cos14310m5-v1.06hpc-en_manual_h-p-cosmos_running_machine.doc © 2012 h/p/cosmos sports & medical gmbh email@h-p-cosmos.com created 15.02.2012 printed 15.02.2012 page: 80 of 213 operation Step Duration Speed Elevation 1 3:00 min 2.7 km/h 10.0 % 2 4.8 km/h 3 6.4 km/h 4 8.0 km/h Step Duration Speed Elevation 1 3:00 min 2.7 km/h 10.0 % 2 4.8 km/h 10.0 % 3 6.4 km/h 10.0 % 4 8.0 km/h 10.0 % 5 8.0 km/h 15.0 % 6 9.6 km/h 15.0 % Ramp profile with 2 parameters: N Target speed: Standard: 10.0 km/h; adjustable from 0 to maximum speed of the treadmill. N Time for reaching target speed in seconds: Standard: 10 seconds; adjustable from 0 to 99 seconds
[7.B13] 11 The „Gardner Testprotocol“ for application Angiology. The Gardner Testprotocol serves for evaluation of the maximum walking distance of Peripheral Arterial Disease Patients with Intermittent Claudication. The test has to be performed under permanent supervision of a doctor and a fall prevention system (e.g. safety arch with chest belt) has to be used. The patient first stands on the side-footboards of the running machine and not on the belt. Start test profile 11 and the belt speeds up to 3.2 km/h. As the patient steps on the running belt the doctor press the START key again and by pressing the START key the second time the displays will be reset to zero. After completing the test the results can be printed on a host printer, if connected to the interface of the running machine directly. Step Duration min:sec file: n:\article\cos14310m5-v1_06hpc-en\20120215_cos14310m5-v1.06hpc-en_manual_h-p-cosmos_running_machine.doc © 2012 h/p/cosmos sports & medical gmbh email@h-p-cosmos.com created 15.02.2012 printed 15.02.2012 page: 81 of 213 operation Speed Elevation Total Time min:sec Pre-Testphase. Patient standing on the footboards, not on the belt 0 until 3.2 km/h 0 until START START is pressed is pressed Testphase. Patient steps onto the running belt. 1 02:00 3.2 km/h 0 2:00 2 02:00 3.2 km/h 2 4:00 3 02:00 3.2 km/h 4 6:00 4 02:00 3.2 km/h 6 8:00 5 02:00 3.2 km/h 8 10:00 6 02:00 3.2 km/h 10 12:00 7 02:00 3.2 km/h 12 14:00 8 02:00 3.2 km/h 14 16:00 9 02:00 3.2 km/h 16 18:00 10 02:00 3.2 km/h 18 20:00 11 30:00 3.2 km/h 18 50:00 12 - 20 not engaged / reserved for following extensions and up-dates 21 - 28 free definable user profiles max. 40 Program steps / not scaleable Additional profiles in the test mode from firmware 3.02.3 – only optionally selectable, locked by default [7.B13] 70 Training Interval 600 m / 14.5 ... 17.5 km/h Step Distance/time Speed Elevation Acceleration 1 600 m 14.5 km/h 0 % 3 2 1:30 min 0.0 km/h 3 600 m 15.5 km/h 4 1:30 min 0.0 km/h 5 600 m 16.5 km/h 6 1:30 min 0.0 km/h 7 600 m 17.5 km/h 8 1:30 min 0.0 km/h
Page 1 and 2:
Operating instructions and service
Page 3 and 4:
Dear customer, We would like to exp
Page 5 and 6:
h/p/cosmos saturn 300/125r h/p/cosm
Page 7 and 8:
file: n:\article\cos14310m5-v1_06hp
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
[3.D] Materials used file: n:\artic
Page 15 and 16:
[3.I] Specific safety or performanc
Page 17 and 18:
[4.]Safety, warnings, precautions,
Page 19 and 20:
Safety Stop = Emergency Stop Extern
Page 21 and 22:
[4.D] General Instructions / Safety
Page 23 and 24:
[4.E4] Connection of units installe
Page 25 and 26:
[4.F] Medical device software safet
Page 27 and 28:
[4.H] Programmable, electrical medi
Page 29 and 30: safety, warnings, precautions, proh
Page 31 and 32: Picture 11: classification of a net
Page 33 and 34: Summary: safety, warnings, precauti
Page 35 and 36: safety, warnings, precautions, proh
Page 37 and 38: Some examples for safety features a
Page 39 and 40: [5.]Application, Indication, Contra
Page 41 and 42: application, indication, contra-ind
Page 43 and 44: application, indication, contra-ind
Page 45 and 46: [6.]Installation & commissioning [6
Page 47 and 48: [6.A2] Transport with trolleys For
Page 49 and 50: [6.C] Electrical installation insta
Page 51 and 52: [6.C2] Electric safety measurements
Page 53 and 54: N Devices with MCU4 control unit (u
Page 55 and 56: Picture top: MCU5-control-board and
Page 57 and 58: installation & commissioning Device
Page 59 and 60: [6.F] Installation, Overview, Check
Page 61 and 62: [7.]Operation [7.A] UserTerminal, k
Page 63 and 64: The indicated values remain, after
Page 65 and 66: [7.B3] Manual mode Initiation: Runn
Page 67 and 68: Initiation: Running-Belt is not mov
Page 69 and 70: [7.B7] Profile outline file: n:\art
Page 71 and 72: [7.B7] profile 5 file: n:\article\c
Page 73 and 74: file: n:\article\cos14310m5-v1_06hp
Page 75 and 76: [7.B10] [06] Confirm personal age [
Page 77 and 78: [7.B12] Test mode and free program
Page 79: [7.B13] 4 Bruce protocol e.g. for E
Page 83 and 84: [7.B13] 74 Training Interval 300 ..
Page 87 and 88: [7.B13] 92 Test profile file: n:\ar
Page 89 and 90: [7.B13] 94 Test profile file: n:\ar
Page 91 and 92: The test-result is the index-value
Page 93 and 94: [7.B16] [13] 2000 meter walking. Wa
Page 95 and 96: [7.B17] [19] Confirm time [20] Conf
Page 97 and 98: [7.B18] Possibilities of interferin
Page 99 and 100: [8.A2] List of user options / optio
Page 103 and 104: [8.A2] OP27 Minimum acceleration an
Page 105 and 106: [8.A3] Standard settings for the us
Page 107 and 108: [8.B1] OP04 Maximum speed for rever
Page 113 and 114: [8.B1] OP39 Elevation: display as s
Page 115 and 116: [8.B1] OP49 Type of frequency inver
Page 119 and 120: [8.B2] Standard settings of adminis
Page 121 and 122: [8.B3] List of running machines typ
Page 123 and 124: [9.B] Immediate maintenance mainten
Page 125 and 126: [9.C4] Equivalent (alternative) lea
Page 127 and 128: maintenance & safety inspections In
Page 129 and 130: [9.D2] Lubricant test maintenance &
Page 131 and 132:
[9.D4] Devices with UserTerminal &
Page 133 and 134:
maintenance & safety inspections Re
Page 135 and 136:
maintenance & safety inspections Pr
Page 137 and 138:
maintenance & safety inspections N
Page 139 and 140:
Medium to achieve hygienic safety:
Page 141 and 142:
[9.L] Spare parts & consumables mai
Page 143 and 144:
[10.]Trouble shooting file: n:\arti
Page 145 and 146:
[10.E] Voltage at the device housin
Page 147 and 148:
[10.I] Error messages / Error codes
Page 149 and 150:
Page 151 and 152:
[10.I1] E51 Error of frequency inve
Page 153 and 154:
[10.I2] Devices without UserTermina
Page 155 and 156:
Dimension of running surface length
Page 157 and 158:
Dimension of running surface length
Page 159 and 160:
Dimension frame length x width x he
Page 161 and 162:
Page 163 and 164:
[11.E1] Interface additional inform
Page 165 and 166:
[12.]Accessories and options file:
Page 167 and 168:
[12.B] Additional keyboard and add.
Page 169 and 170:
[12.C1] Danger precaution and opera
Page 171 and 172:
[02] [03] [04] [05] file: n:\articl
Page 173 and 174:
[02] [03] Total view running machin
Page 175 and 176:
[12.G] h/p/cosmos airwalk se 135 (a
Page 177 and 178:
[12.I] h/p/cosmos robowalk ® expan
Page 179 and 180:
picture type of stop function inter
Page 181 and 182:
[12.M2] Change from forward to reve
Page 183 and 184:
[12.P] Retrofitting / additional sa
Page 185 and 186:
[12.S] Digital (serial) RS232 inter
Page 187 and 188:
[12.T] Printer protocol file: n:\ar
Page 189 and 190:
[12.U4] Battery of the transmitter
Page 191 and 192:
[12.W] PC Software h/p/cosmos para
Page 193 and 194:
[12.Y] PC Software h/p/cosmos para
Page 195 and 196:
[13.B] Certificate of the TSA (TÜV
Page 197 and 198:
[13.D] Certificate of compliance fo
Page 199 and 200:
Page 201 and 202:
[14.]Disposal file: n:\article\cos1
Page 203 and 204:
[16.]Appendix - Instruction and com
Page 205 and 206:
[06] [07] [08] [09] file: n:\articl
Page 207 and 208:
[06] [07] [16.D] Advice and support
Page 209 and 210:
[16.F] Service report - cos15531 fi
Page 211 and 212:
[16.H] Wiring diagram load circuit
Page 213:
[16.J] Wiring diagram control circu
show all

running machine - H-P-COSMOS Sports and Medical

Create successful ePaper yourself

Delete template?

Save as template?