Curlin 4000 User Manual - Med-E-Quip Locators

More documents

Recommendations

Info

Procedure for Checking Pumps Between PatientsPurposeThis Pump Test Procedure is for use by Technicians to inspect, test and prepare a pump foruse by a new patient. It checks volumetric delivery accuracy and all pump safety systems.Also initialization is performed for various parameters.This procedure is intended to be used by Technicians familiar with operation of the <strong>Curlin</strong><strong>Med</strong>ical Infusion Pump.Note: This procedure does not replace the recommended Annual Preventive Maintenance.The pump should receive preventive maintenance by a qualified technician annually.Required EquipmentThe following equipment is required for this procedure:• A NEW Administration Set (old or used sets are not suitable for the volumetric deliveryand pressure measurements tests.)• Volumetric measurement device (i.e. calibrated weight scale, burette or syringe.)• Beaker with clean, fresh water or I.V. container.Note: If the administration set contains a filter, sterile saline or sterile water should be used.Maintenance Between PatientsThis procedure does not replace the recommended preventive maintenance. The pumpshould receive preventive maintenance by a qualified technician annually.1 CLEAN AND INSPECT PUMP FOR DAMAGE:a Clean the pump with a soft cloth dampened with a designated antiseptic, disinfectantsolution or a solution of household bleach diluted 9:1 with water. Be sure to clean allsurfaces, including the pumping chamber.b Inspect pump for damage. Check all case surfaces for cracks. Open the pumpingchamber door. Examine the finger seal to confirm that no cuts or tears exist.Confirm that the door is well aligned by closing it with no unreasonable interference.Verify that the Power and Bolus/Data connectors are securely mounted on the case(no loose nuts). Verify that all labels are legible and in good condition. Check thatKeypad is securely attached to case and that no corners are pealing up. Verify thatthe Battery Door is in place and that the Battery Contacts in the BatteryCompartment are not deformed.2 VOLUMETRIC DELIVERY TEST:a Install a new primed Administration Set in the pump and latch the door.b Connect the up-stream side of administration set to a un-pressurized water source.c Connect the down stream side of administration set to a volumetric measurementdevice (i.e. a calibrated scale or burette).148
d Program the following CONTINUOUS Infusion:Pre Rx:UNITS: mlDELAY: OFFTitrate: OFFNEXT? YESPrescription:BAG VOL: 100 mlVOL TBI: 10.0 mlRATE: 125 ml/hrTIME: 0:04 HH:MMKVO Rate: 0.0 ml/hrDONE? YESe Start the continuous therapy running by pressing RUN button.f When the 10 ml infusion is over, observe the amount volume infused as measuredon the measurement device. Passing measurement is: 9.5 g to 10.50 g (9.5ml to10.5ml).g When Infusion complete occurs verify that the Audio Alarm is beeping and that theGreen and Red LEDs are flashing.3 CHECK ALL SAFETY SYSTEMS:a Low Down Stream Occlusion - Repeat the same Continuous Infusion as above.Go to the Option screen and confirm that the Down Occlusion level is set to LOW.Start the infusion and while the pump is running pinch off or close the down streamside of the administration set. Confirm the pump goes into Down Occlusion alarm.Open or clear the down stream occlusion and confirm the pump resumes infusion.b High Down Stream Occlusion – Go to the Option screen and change the DownOcclusion level to HIGH. Again pinch off or close the clamp on the down-streamside of the administration set. Confirm the pump goes into Down Occlusion. Openor clear the down stream occlusion and confirm the pump resumes infusion.c Up Stream Occlusion - Resume the infusion pumping then pinch off or close theup-stream side of the administration set. Confirm that the pump goes into an UpOcclusion alarm. Open or clear the up stream occlusion, press Pause then Resumethe infusion.d Door Sensor - With infusion in progress open the door latch and observe ALARMDOOR OPEN OR SET NOT INSTALLED.e Air In Line Sensor - Reinstall the administration set properly and resume theinfusion. From the Options menu set the AIL SENS (AIR IN LINE sensitivity) to0.1ml. With the pump running introduce an Air Bolus of approximately 0.5ml intothe fluid path at the input side of the pump. Once approximately 0.1ml of air haspast the AIL detector, an ALARM AIR IN LINE will occur. Pause and Prime theair bolus past the AIL sensor, then resume the infusion.f Auxiliary Alarm - With the pump running observe the Vol INF (volume infused onthe run screen) and disconnect the pump from all power sources (unplug the ACCleaning, Maintenance149
Page 1 and 2:
CURLIN MEDICALUser’s Manualfor us
Page 3 and 4:
TABLE OF CONTENTSEntering or Changi
Page 5 and 6:
TABLE OF CONTENTSPrime.............
Page 7 and 8:
IntroductionChapter1IntroductionThe
Page 9 and 10:
• Retained memory features that a
Page 11 and 12:
CAUTIONS• U.S. federal law restri
Page 13 and 14:
• This equipment generates, uses,
Page 15 and 16:
Serial Number LabelIntroductionBatt
Page 17 and 18:
Preparing Medication for Infusion/C
Page 19 and 20:
Opening and Closing the Pump DoorTh
Page 21 and 22:
Air DetectorNote: Open theslide cla
Page 23 and 24:
Installing the Batteries and Using
Page 25 and 26:
IMPORTANTINFORMATIONWhenever an ext
Page 27 and 28:
IntroductionLocking SleeveTwo-Pin A
Page 29 and 30:
Chapter2Learning Pump FeaturesLearn
Page 31 and 32:
LED Light IndicatorsThis “three-l
Page 33 and 34:
Chapter3Basics of ProgrammingThe Cu
Page 35 and 36:
whenever an alarm or error code occ
Page 37 and 38:
Access CodeClinician Access Code Sc
Page 39 and 40:
to all pump functions. Each level h
Page 41 and 42:
8 PRINT PATIENT HISTORY: To print t
Page 43 and 44:
a. Time Format: You have the option
Page 45 and 46:
If only one therapy is programmed a
Page 47 and 48:
Chapter4Continuous TherapyContinuou
Page 49 and 50:
If the KVO rate is set to 0, the pu
Page 51 and 52:
6 DONE?: If any changes are to be m
Page 53 and 54:
The following screen displays the C
Page 55 and 56:
detects in-line pressures at 400 mm
Page 57 and 58:
In CMS-enabled pumps, the graphic b
Page 59 and 60:
. If the incomplete therapy is to b
Page 61 and 62:
PCA TherapyChapter5PCA TherapyPCA o
Page 63 and 64:
a. MxRATE (Maximum Rate) limits: Us
Page 65 and 66:
using the numeric keys and, when co
Page 67 and 68:
Note. After the infusion has starte
Page 69 and 70:
d. To exit the shift total feature
Page 71 and 72:
pressures at 400 mmHg ±150 (8 ±3
Page 73 and 74:
This screen will continue to displa
Page 75 and 76:
When the program is accepted, the d
Page 77:
which therapy to repeat by moving t
Page 80 and 81:
The time format (12 hr AM/PM or 24
Page 82 and 83:
time period using the numeric keys,
Page 84 and 85:
7 To continue priming, press the PR
Page 86 and 87:
Note: Whatever Down Ramp time was a
Page 88 and 89:
1 The first field displays the “R
Page 90 and 91:
. If the incomplete therapy is to b
Page 95 and 96:
IMPORTANTINFORMATIONDuring the dela
Page 97 and 98:
10 DONE?: If there are any changes
Page 99 and 100:
The following screen displays the I
Page 101 and 102:
This message alerts you to the Air-
Page 103 and 104: Intermittent Information ScreensInt
Page 105 and 106: Intermittent Dosing ScheduleThe dos
Page 107 and 108: This screen displays:1 “INFUSION
Page 109 and 110: CHAPTER8Variable TherapyThis therap
Page 111 and 112: During the delay start period, if t
Page 113 and 114: 5 NEXT?: If there are any changes t
Page 115 and 116: 7 To continue priming, press the PR
Page 117 and 118: 4 DN Occlu (Down Occlusion): This f
Page 119 and 120: Variable Run Screen 2This screen di
Page 121 and 122: stop the auto-advance function by p
Page 123 and 124: The pump will then display the prog
Page 125 and 126: TroubleshootingChapter9Troubleshoot
Page 127 and 128: LCD Display:Alert:Cause:Resolution:
Page 129 and 130: If it is not necessary to preserve
Page 131 and 132: Resolution:LCD Display:Alert:Cause:
Page 133 and 134: LCD Display: ALERT NEW DOSE IS LESS
Page 135 and 136: LCD Display:Alert:Cause:Resolution:
Page 137 and 138: ALARMSAlarms are conditions that re
Page 139 and 140: LCD Display:Alarm:Cause:Resolution:
Page 141 and 142: ERROR CODESIf a pump goes into an e
Page 143 and 144: ErrorCodeLCD DisplayedMessage162 St
Page 145 and 146: ChapterAccessories10There are a num
Page 147 and 148: AccessoriesFigure 10.3 Safety Shell
Page 149 and 150: Keypad CoversThese accessories are
Page 151 and 152: Chapter11Cleaning, EnvironmentalCon
Page 153: 1 PARTIES COVERED BY THIS WARRANTY:
Page 157 and 158: Chapter12TechnicalSpecificationsThe
Page 159 and 160: ITEMDown Occlusion Detection TimeMi
Page 161 and 162: Curlin pump inusing at .1 ml/hr w i
Page 163 and 164: Percent Error, Curlin Pump infusing
Page 165 and 166: Clinician Information andAccess Cod
show all

Curlin 4000 User Manual - Med-E-Quip Locators

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?