Curlin 4000 User Manual - Med-E-Quip Locators

More documents

Recommendations

Info

When you select a number, the pump will beep at that audio level. Press the “NO” key andenter a new setting (1 – 9). Repeat until the desired setting is reached, and then press“YES/ENTER” to select it and move the cursor to the next field.8 PWR CK? (Power Check): This feature allows you to periodically recheck the battery charge.It will display the active power source of the pump, whether internal batteries or externalpower. If the active source is the batteries, a graph will indicate approximately how muchcharge remains in the batteries. To access this information, select “ON” and press“YES/ENTER”. The Power Source Screen will display for five seconds and return to theOptions Menu.9 ACCEPT OPT?: If the changes made in the Options Menu are acceptable, press the“YES/ENTER” key. If the changes are not acceptable, use arrow keys to cursor up to anyfield for corrections, or abort all changes made in this menu by pressing the “NO” key andreturn to the previous screen.There are two remaining selections to consider from the “Run Options Screen,” NO toREVIEW, and RUN to START.Reviewing or Changing the ProgramTo review or make any changes in the prescription programming, press the “NO/CHANGE”key at the Run Options screen, and the prescription screens will reappear (Changes may beinhibited by lock setting.) Changes to the prescription can be made before the start of thetherapy; however, once a therapy has started, no changes can be made to the Pre-PrescriptionScreen. It will appear only for review purposes. Attempts to change the Pre-Prescription Menuduring a new program review will cause an alert screen to be displayed, notifying the programmerthat changes will require reprogramming of the prescription.Starting the InfusionRUN: When all parameters are correct and the pump has been primed properly and connectedto the access site, press “RUN” at the Run Options screen to start the therapy. If a delayed startis programmed, the “Delay Start Count Down Screen” will appear. If no delay start isprogrammed or the delay has elapsed, the pump will begin infusing and the following screen willdisplay the status of the therapy:Continuous Run ScreenThis screen displays as long as the infusion is running. Notice the information on each field:1 The first line displays the rate of the infusion in whichever units/hour has been selected. Thisinformation toggles with the programmed “Amount To Be Infused.”2 The second line displays a graphic bar representing the percentage of the completed infusion.50
In CMS-enabled pumps, the graphic bar will toggle with Line Pressure (“L Press”)which displays the current patient side (downstream) pressure in the administrationset in millimeter of mercury (mmHg) units.3 The third line displays the total volume infused and, if mg or mcg is the selected unit, this fieldwill toggle to display the total (mg or mcg) infused as well.4 The last line displays the remaining time to the completion of the infusion toggled with theremaining amount to be infused.5 In addition to the display screen giving information regarding the status of the infusion, thegreen LED light blinks whenever the pump is infusing.The information on the run screen will alternate between a four-line display and a large-fontdisplay of each line of information on the screen.Continuous Information ScreensInterrupting an InfusionThe infusion can be paused at any time by pressing the “PAUSE” key. The yellow “Standby”LED light blinks, and the following screen displays:Pause Menu ScreenContinuous Therapy51
Page 1 and 2:
CURLIN MEDICALUser’s Manualfor us
Page 3 and 4:
TABLE OF CONTENTSEntering or Changi
Page 5 and 6: TABLE OF CONTENTSPrime.............
Page 7 and 8: IntroductionChapter1IntroductionThe
Page 9 and 10: • Retained memory features that a
Page 11 and 12: CAUTIONS• U.S. federal law restri
Page 13 and 14: • This equipment generates, uses,
Page 15 and 16: Serial Number LabelIntroductionBatt
Page 17 and 18: Preparing Medication for Infusion/C
Page 19 and 20: Opening and Closing the Pump DoorTh
Page 21 and 22: Air DetectorNote: Open theslide cla
Page 23 and 24: Installing the Batteries and Using
Page 25 and 26: IMPORTANTINFORMATIONWhenever an ext
Page 27 and 28: IntroductionLocking SleeveTwo-Pin A
Page 29 and 30: Chapter2Learning Pump FeaturesLearn
Page 31 and 32: LED Light IndicatorsThis “three-l
Page 33 and 34: Chapter3Basics of ProgrammingThe Cu
Page 35 and 36: whenever an alarm or error code occ
Page 37 and 38: Access CodeClinician Access Code Sc
Page 39 and 40: to all pump functions. Each level h
Page 41 and 42: 8 PRINT PATIENT HISTORY: To print t
Page 43 and 44: a. Time Format: You have the option
Page 45 and 46: If only one therapy is programmed a
Page 47 and 48: Chapter4Continuous TherapyContinuou
Page 49 and 50: If the KVO rate is set to 0, the pu
Page 51 and 52: 6 DONE?: If any changes are to be m
Page 53 and 54: The following screen displays the C
Page 55: detects in-line pressures at 400 mm
Page 59 and 60: . If the incomplete therapy is to b
Page 61 and 62: PCA TherapyChapter5PCA TherapyPCA o
Page 63 and 64: a. MxRATE (Maximum Rate) limits: Us
Page 65 and 66: using the numeric keys and, when co
Page 67 and 68: Note. After the infusion has starte
Page 69 and 70: d. To exit the shift total feature
Page 71 and 72: pressures at 400 mmHg ±150 (8 ±3
Page 73 and 74: This screen will continue to displa
Page 75 and 76: When the program is accepted, the d
Page 77: which therapy to repeat by moving t
Page 80 and 81: The time format (12 hr AM/PM or 24
Page 82 and 83: time period using the numeric keys,
Page 84 and 85: 7 To continue priming, press the PR
Page 86 and 87: Note: Whatever Down Ramp time was a
Page 88 and 89: 1 The first field displays the “R
Page 90 and 91: . If the incomplete therapy is to b
Page 95 and 96: IMPORTANTINFORMATIONDuring the dela
Page 97 and 98: 10 DONE?: If there are any changes
Page 99 and 100: The following screen displays the I
Page 101 and 102: This message alerts you to the Air-
Page 103 and 104: Intermittent Information ScreensInt
Page 105 and 106: Intermittent Dosing ScheduleThe dos
Page 107 and 108:
This screen displays:1 “INFUSION
Page 109 and 110:
CHAPTER8Variable TherapyThis therap
Page 111 and 112:
During the delay start period, if t
Page 113 and 114:
5 NEXT?: If there are any changes t
Page 115 and 116:
7 To continue priming, press the PR
Page 117 and 118:
4 DN Occlu (Down Occlusion): This f
Page 119 and 120:
Variable Run Screen 2This screen di
Page 121 and 122:
stop the auto-advance function by p
Page 123 and 124:
The pump will then display the prog
Page 125 and 126:
TroubleshootingChapter9Troubleshoot
Page 127 and 128:
LCD Display:Alert:Cause:Resolution:
Page 129 and 130:
If it is not necessary to preserve
Page 131 and 132:
Resolution:LCD Display:Alert:Cause:
Page 133 and 134:
LCD Display: ALERT NEW DOSE IS LESS
Page 135 and 136:
LCD Display:Alert:Cause:Resolution:
Page 137 and 138:
ALARMSAlarms are conditions that re
Page 139 and 140:
LCD Display:Alarm:Cause:Resolution:
Page 141 and 142:
ERROR CODESIf a pump goes into an e
Page 143 and 144:
ErrorCodeLCD DisplayedMessage162 St
Page 145 and 146:
ChapterAccessories10There are a num
Page 147 and 148:
AccessoriesFigure 10.3 Safety Shell
Page 149 and 150:
Keypad CoversThese accessories are
Page 151 and 152:
Chapter11Cleaning, EnvironmentalCon
Page 153 and 154:
1 PARTIES COVERED BY THIS WARRANTY:
Page 155 and 156:
d Program the following CONTINUOUS
Page 157 and 158:
Chapter12TechnicalSpecificationsThe
Page 159 and 160:
ITEMDown Occlusion Detection TimeMi
Page 161 and 162:
Curlin pump inusing at .1 ml/hr w i
Page 163 and 164:
Percent Error, Curlin Pump infusing
Page 165 and 166:
Clinician Information andAccess Cod
show all

Curlin 4000 User Manual - Med-E-Quip Locators

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?