Curlin 4000 User Manual - Med-E-Quip Locators

More documents

Recommendations

Info

Keypad Function1 ON/OFF: Used to turn the pump on and off. When the pump is running, however, the“PAUSE” key must be used to stop the infusion first and then the “OFF” key can be pressedto turn the pump off. This requirement prevents the interruption of an infusion by a singleaccidental press of the “OFF” key.2 RUN/PAUSE: Used to start or pause the motor of the pump, which, in turn, starts orpauses fluid delivery. When the pump is running, pressing this key will pause the pump.When the pump is paused, pressing this key during the “Run Options” menu will start thepump. This key is also used to terminate a pump alarm.Note: If the cause of the alarm is not resolved when the pump is “Resumed,” the alarm willrecur.3 ⇑ Up arrow: Used to scroll the highlight bar or field cursor up on the display screen.Note: The Up arrow will not accept a selection which must be made with a YES/ENTERor NO/CHANGE key.4 ⇓ Down arrow: Used to scroll the highlight bar or field cursor down on the display screen.Note: The Down arrow will not accept a selection which must be made with aYES/ENTER or NO/CHANGE key.5 NO/CHANGE: Used to respond “NO” to data or questions presented or to reject or tochange highlighted data.Note: The Curlin Medical pump requires you to actively change a selection. The Up arrowor Down arrow will not change a selection.6 YES/ENTER: Used to respond “YES/ENTER” to data or questions presented or to“accept” highlighted data when prompted to press “enter” key.Note: The Curlin Medical pump requires you to affirmatively accept a selection. The Uparrow or Down arrow will not accept a selection.7 HELP/OPTIONS: Used to request a help screen when the pump is paused or is at the“Infusion Complete Screen.” It is also used to access the options screen when the pump isrunning. When the options screen is displayed, help is again available with this key. When ina help screen, use the arrow keys to scroll through the help message, and then press the helpkey again to exit help.8 ./SILENCE: Used as a decimal point when programming numeric data. Used also totemporarily silence the alarm (for one-minute intervals).9 PRIME/BOLUS: Used to prime fluid through the tubing to clear it of air or to administera patient demand bolus dose of medication in PCA therapy.10 0 - 9 Numeric keys: - Used for data entry.24
LED Light IndicatorsThis “three-light” feature gives the user feed back on the current status of the pump.1 Green indicates a RUNNING status of the pump and blinks approximately once every threeseconds when a therapy is in progress.2 Yellow indicates a STANDBY status of the pump and blinks while the pump is paused.3 Red indicates a STOPPED or ALARM status of the pump and blinks whenever an alarmstatus exists.4 Green and Red indicates an “Infusion Complete Alarm” status with KVO or a DownOcclusion Alarm with automatic restart.5 Yellow and Green indicates a “Standby” status with automatic start. This occurs during anydelay start with a “0” KVO programmed or in PCA during a “0” basal rate and bolus onlyprogrammed.Audio IndicatorAn audible alarm or “beep” is used to alert you to a change in the status of the pump or asituation requiring user action or notification. A message will appear on the display screendescribing the situation. The rate, number of beeps, and volume further specify status. Thispump offers nine different volume levels from which to select for the audio feature; however, the“beep” cannot be totally disabled. The audio “beep” can be silenced for one-minute intervals bypressing the “SILENCE” key except during an “Error Code,” at which time the alarm continuesand the pump must be turned off. The chapter of this manual entitled, Troubleshooting includestables with the alerts, alarms, and error codes, the conditions causing them, the message displayedon the screen, and the actions required for resolution. If an alert or alarm occurs, please refer tothese tables.Learning PumpDisplay ScreenThe display screen provides a maximum of four lines of text, or fields, at any one time forfeedback regarding the pump status and data entry. It notifies the user with prompts or messageswhen necessary. The screen has backlighting that remains:• on if connected to an AC outlet;• lit for 15 seconds if using batteries or during any key press sequences,• on with alert/alarm messages.When no keys are pressed for fifteen seconds, the light goes off to conserve battery power.Backlighting is resumed with any key press.In most displays, a “Therapy Identifier” Bar appears at the far left of the screen, indicating whichtherapy is running or which programming screen is being considered. This identifier also hasanother function, and that is to alert you when more text exists either above the top line or belowthe bottom line on the display screen. The identifier bar will have an arrow configuration eitherpointing up or down or both whenever there is more text, or it will appear as a squared-off blockif no further text exists.25
Page 1 and 2: CURLIN MEDICALUser’s Manualfor us
Page 3 and 4: TABLE OF CONTENTSEntering or Changi
Page 5 and 6: TABLE OF CONTENTSPrime.............
Page 7 and 8: IntroductionChapter1IntroductionThe
Page 9 and 10: • Retained memory features that a
Page 11 and 12: CAUTIONS• U.S. federal law restri
Page 13 and 14: • This equipment generates, uses,
Page 15 and 16: Serial Number LabelIntroductionBatt
Page 17 and 18: Preparing Medication for Infusion/C
Page 19 and 20: Opening and Closing the Pump DoorTh
Page 21 and 22: Air DetectorNote: Open theslide cla
Page 23 and 24: Installing the Batteries and Using
Page 25 and 26: IMPORTANTINFORMATIONWhenever an ext
Page 27 and 28: IntroductionLocking SleeveTwo-Pin A
Page 29: Chapter2Learning Pump FeaturesLearn
Page 33 and 34: Chapter3Basics of ProgrammingThe Cu
Page 35 and 36: whenever an alarm or error code occ
Page 37 and 38: Access CodeClinician Access Code Sc
Page 39 and 40: to all pump functions. Each level h
Page 41 and 42: 8 PRINT PATIENT HISTORY: To print t
Page 43 and 44: a. Time Format: You have the option
Page 45 and 46: If only one therapy is programmed a
Page 47 and 48: Chapter4Continuous TherapyContinuou
Page 49 and 50: If the KVO rate is set to 0, the pu
Page 51 and 52: 6 DONE?: If any changes are to be m
Page 53 and 54: The following screen displays the C
Page 55 and 56: detects in-line pressures at 400 mm
Page 57 and 58: In CMS-enabled pumps, the graphic b
Page 59 and 60: . If the incomplete therapy is to b
Page 61 and 62: PCA TherapyChapter5PCA TherapyPCA o
Page 63 and 64: a. MxRATE (Maximum Rate) limits: Us
Page 65 and 66: using the numeric keys and, when co
Page 67 and 68: Note. After the infusion has starte
Page 69 and 70: d. To exit the shift total feature
Page 71 and 72: pressures at 400 mmHg ±150 (8 ±3
Page 73 and 74: This screen will continue to displa
Page 75 and 76: When the program is accepted, the d
Page 77: which therapy to repeat by moving t
Page 80 and 81:
The time format (12 hr AM/PM or 24
Page 82 and 83:
time period using the numeric keys,
Page 84 and 85:
7 To continue priming, press the PR
Page 86 and 87:
Note: Whatever Down Ramp time was a
Page 88 and 89:
1 The first field displays the “R
Page 90 and 91:
. If the incomplete therapy is to b
Page 95 and 96:
IMPORTANTINFORMATIONDuring the dela
Page 97 and 98:
10 DONE?: If there are any changes
Page 99 and 100:
The following screen displays the I
Page 101 and 102:
This message alerts you to the Air-
Page 103 and 104:
Intermittent Information ScreensInt
Page 105 and 106:
Intermittent Dosing ScheduleThe dos
Page 107 and 108:
This screen displays:1 “INFUSION
Page 109 and 110:
CHAPTER8Variable TherapyThis therap
Page 111 and 112:
During the delay start period, if t
Page 113 and 114:
5 NEXT?: If there are any changes t
Page 115 and 116:
7 To continue priming, press the PR
Page 117 and 118:
4 DN Occlu (Down Occlusion): This f
Page 119 and 120:
Variable Run Screen 2This screen di
Page 121 and 122:
stop the auto-advance function by p
Page 123 and 124:
The pump will then display the prog
Page 125 and 126:
TroubleshootingChapter9Troubleshoot
Page 127 and 128:
LCD Display:Alert:Cause:Resolution:
Page 129 and 130:
If it is not necessary to preserve
Page 131 and 132:
Resolution:LCD Display:Alert:Cause:
Page 133 and 134:
LCD Display: ALERT NEW DOSE IS LESS
Page 135 and 136:
LCD Display:Alert:Cause:Resolution:
Page 137 and 138:
ALARMSAlarms are conditions that re
Page 139 and 140:
LCD Display:Alarm:Cause:Resolution:
Page 141 and 142:
ERROR CODESIf a pump goes into an e
Page 143 and 144:
ErrorCodeLCD DisplayedMessage162 St
Page 145 and 146:
ChapterAccessories10There are a num
Page 147 and 148:
AccessoriesFigure 10.3 Safety Shell
Page 149 and 150:
Keypad CoversThese accessories are
Page 151 and 152:
Chapter11Cleaning, EnvironmentalCon
Page 153 and 154:
1 PARTIES COVERED BY THIS WARRANTY:
Page 155 and 156:
d Program the following CONTINUOUS
Page 157 and 158:
Chapter12TechnicalSpecificationsThe
Page 159 and 160:
ITEMDown Occlusion Detection TimeMi
Page 161 and 162:
Curlin pump inusing at .1 ml/hr w i
Page 163 and 164:
Percent Error, Curlin Pump infusing
Page 165 and 166:
Clinician Information andAccess Cod
show all

Curlin 4000 User Manual - Med-E-Quip Locators

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?