Multilin 469 Motor Management Relay ... - GE Digital Energy

More documents

Recommendations

Info

Note MESSAGE MESSAGE MESSAGE MESSAGE MESSAGE MESSAGE MESSAGE MESSAGE MESSAGE MESSAGE MESSAGE MESSAGE HOTTEST BEARING RTD HOTTEST OTHER RTD RTD #11: 0°C Pre- AMBIENT RTD RTD#12: 0°C Pre- Vab: 0 Vbc: 0 Van: 0 Vbn: 0 PRETRIP SYSTEM FREQUENCY: 0.00 kVA 0 kW 0 POWER FACTOR PreTrip: 0.00 Analog I/P 1 PreTrip: 0 Units Analog I/P 2 PreTrip: 0 Units Analog I/P 3 PreTrip: 0 Units Analog I/P 4 PreTrip: 0 Units CHAPTER 6: ACTUAL VALUES Range: –50 to 250°C or –58 to 482°F. Seen only if at least 1 RTD is set as Bearing Range: –50 to 250°C or –58 to 482°F. Seen only if at least 1 RTD is set as Other Range: –50 to 250°C or –58 to 482°F. Seen only if at least 1 RTD is set as Ambient Range: 0 to 20000 V. Not seen if VT Connection is set as None Range: 0 to 20000 V. Seen only if VT Connection is set as Wye Range: Not seen if VT Connect. set as None Range: –50000 to 50000 kVA. Not seen if VT Connection set as None Range: 0.01 to 0.99 Lead or Lag, 0.00, 1.00. Not seen if VT Connection is set as “None” Range: –50000 to 50000. Not seen if Analog Input 1 is “Disabled”. Range: –50000 to 50000. Not seen if Analog Input 2 is “Disabled”. Range: –50000 to 50000. Not seen if Analog Input 3 is “Disabled”. Range: –50000 to 50000. Not seen if Analog Input 4 is “Disabled”. Immediately prior to issuing a trip, the 469 takes a snapshot of motor parameters and stores them as pre-trip values that allow for troubleshooting after the trip occurs. The CAUSE OF LAST TRIP message is updated with the current trip and the screen defaults to that message. All trip features are automatically logged as date and time stamped events as they occur. This information may include motor speed (2-Speed feature or Assignable Digital Input), phase and ground currents, RTD temperatures, voltages, frequency, power quantities, and analog inputs. This information can be cleared using the S1 469 SETUP CLEAR DATA CLEAR LAST TRIP DATA settings. The CAUSE OF LAST TRIP actual value has the following range: No Trip to Date, Incomplete Sequence, Remote Trip, Speed Switch, Load Shed, Pressure Switch, Vibration Switch, General Sw, Overload, Short Circuit, Mechanical Jam, Undercurrent, Current Unbalance, Ground Fault, Phase Differential, Acceleration, Tachometer, RTDs #1 to #12, Undervoltage, Overvoltage, Phase Reversal, Frequency, Reactive Power, Power Factor, Underpower, Analog Inputs 1 to 4, Single Phasing, Reverse Power, Analog Diff 1-2, Analog Diff 3-4. Phase, differential, and ground currents are recorded 1 cycle prior to the trip. All other pretrip data is recorded 50 ms prior to the trip. Thus some values will not be recorded upon instantaneous trips during a start if the trip is less than 50 ms. 6–6 469 MOTOR MANAGEMENT RELAY – INSTRUCTION MANUAL
CHAPTER 6: ACTUAL VALUES 6.2.4 Alarm Status PATH: ACTUAL VALUES A1 STATUS ALARM STATUS ALARM STATUS [] MESSAGE MESSAGE MESSAGE MESSAGE MESSAGE MESSAGE MESSAGE MESSAGE MESSAGE MESSAGE MESSAGE MESSAGE MESSAGE MESSAGE MESSAGE MESSAGE MESSAGE MESSAGE NO ALARMS REMOTE ALARM STATUS: Active PRESSURE SWITCH ALARM STATUS: VIBRATION SWITCH ALARM STATUS: DIG. COUNTER ALARM: TACHOMETER ALARM: 3000 RPM GENERAL SW. A ALARM STATUS: THERMAL CAPACITY ALARM: 100% USED XX.XX x FLA OVER- LOAD UNDERCURRENT ALARM CURRENT UNBALANCE ALARM: 15% GROUND FAULT ALARM: 25.3 A STATOR RTD #1 ALARM: 135°C OPEN SENSOR ALARM: SHORT/LOW TEMP ALARM UNDERVOLTAGE ALARM OVERVOLTAGE ALARM Vab= 4992 V 120% SYSTEM FREQUENCY ALARM: 59.4 Hz POWER FACTOR ALARM PF: 0.00 Range: N/A. Message seen when no alarms are active Range: Active, Latched Range: Active, Latched Range: Active, Latched Range: 1 to 9999999999. Displays current value of digital counter Range: 0 to 3600 RPM. Displays current Tachometer Digital Input value Range: Active, Latched Range: 1 to 100. Thermal Capacity Used value is shown here Range: 0 to 99999 s. Shows overload level and estimated time to trip. Range: 1 to 5000 A; 5 to 99% FLA. Lowest phase current shown. Range: 0 to 100%. Reflects the present unbalance level Range: 0.1 to 5000 A. Reflects the present ground current level Range: –50 to 250°C Range: RTD with the open sensor as programmed for RTDs 1 to 12 Range: 1 to 12. Shows RTD with the short/low temperature alarm Range: 0 to 20000 V; 50 to 99% of Rated Range: 0 to 20000 V; 101 to 150% of Rated Range: 0.00, 20.00 to 120.00 Hz Range: 0.00 to 0.99 Lead or Lag, 0.00, 1.00 469 MOTOR MANAGEMENT RELAY – INSTRUCTION MANUAL 6–7
Page 1 and 2:
Software Revision: 5.1x Manual P/N:
Page 3 and 4:
TOC TABLE OF CONTENTS Table of Cont
Page 5 and 6:
TOC TABLE OF CONTENTS LOADING NEW F
Page 7 and 8:
TOC TABLE OF CONTENTS LAST TRIP DAT
Page 9 and 10:
Digital Energy Multilin 1.1 Importa
Page 11 and 12:
CHAPTER 1: GETTING STARTED 1.2 Usin
Page 13 and 14:
CHAPTER 1: GETTING STARTED To enter
Page 15 and 16:
CHAPTER 1: GETTING STARTED Press t
Page 17 and 18:
CHAPTER 1: GETTING STARTED 1.3 Chan
Page 19 and 20:
CHAPTER 1: GETTING STARTED 1.3.4 En
Page 21 and 22:
CHAPTER 1: GETTING STARTED SETTING
Page 23 and 24:
CHAPTER 1: GETTING STARTED 1.3.5 Ou
Page 25 and 26:
CHAPTER 1: GETTING STARTED 1.4 Appl
Page 27 and 28:
CHAPTER 1: GETTING STARTED To begin
Page 29 and 30:
CHAPTER 1: GETTING STARTED FIGURE 1
Page 31 and 32:
CHAPTER 1: GETTING STARTED • Powe
Page 33 and 34:
CHAPTER 1: GETTING STARTED • RTDs
Page 35 and 36:
CHAPTER 1: GETTING STARTED 469 Moto
Page 37 and 38:
CHAPTER 1: GETTING STARTED • Star
Page 39 and 40:
CHAPTER 1: GETTING STARTED For curr
Page 41 and 42:
CHAPTER 1: GETTING STARTED 1.4.6 S5
Page 43 and 44:
CHAPTER 1: GETTING STARTED 1.4.8 S7
Page 45 and 46:
CHAPTER 1: GETTING STARTED if the m
Page 47 and 48:
2.1 Overview Digital Energy Multili
Page 49 and 50:
CHAPTER 2: INTRODUCTION 51 Overload
Page 51 and 52:
CHAPTER 2: INTRODUCTION 2.1.3 Order
Page 53 and 54:
CHAPTER 2: INTRODUCTION 2.2.2 Outpu
Page 55 and 56:
CHAPTER 2: INTRODUCTION Timing accu
Page 57 and 58:
CHAPTER 2: INTRODUCTION 2.2.4 Digit
Page 59 and 60:
CHAPTER 2: INTRODUCTION Note 2.2.6
Page 61 and 62:
CHAPTER 2: INTRODUCTION 2.2.10 Cert
Page 63 and 64:
Digital Energy Multilin 3.1 Mechani
Page 65 and 66:
CHAPTER 3: INSTALLATION 3.1.3 Insta
Page 67 and 68:
CHAPTER 3: INSTALLATION 3.1.4 Unit
Page 69 and 70:
CHAPTER 3: INSTALLATION 3.1.5 Ether
Page 71 and 72:
CHAPTER 3: INSTALLATION 3.1.7 Termi
Page 73 and 74:
CHAPTER 3: INSTALLATION 3.2 Electri
Page 75 and 76:
CHAPTER 3: INSTALLATION 3.2.4 Curre
Page 77 and 78:
CHAPTER 3: INSTALLATION FIGURE 3-15
Page 79 and 80:
CHAPTER 3: INSTALLATION 3.2.5 Volta
Page 81 and 82:
CHAPTER 3: INSTALLATION 3.2.7 Analo
Page 83 and 84:
CHAPTER 3: INSTALLATION Hot Compens
Page 85 and 86:
CHAPTER 3: INSTALLATION relays, bei
Page 87 and 88:
CHAPTER 3: INSTALLATION 3.2.13 Diel
Page 89 and 90:
CHAPTER 3: INSTALLATION 3.2.14 2-Sp
Page 91 and 92:
Digital Energy Multilin 4.1 Facepla
Page 93 and 94:
CHAPTER 4: INTERFACES 4.1.4 RS232 P
Page 95 and 96:
CHAPTER 4: INTERFACES The MESSAGE
Page 97 and 98:
CHAPTER 4: INTERFACES 4.1.7 Diagnos
Page 99 and 100:
CHAPTER 4: INTERFACES 4.1.9 Flash M
Page 101 and 102:
CHAPTER 4: INTERFACES 4.2.2 Hardwar
Page 103 and 104:
CHAPTER 4: INTERFACES 4.2.3 Install
Page 105 and 106:
CHAPTER 4: INTERFACES Click on Nex
Page 107 and 108:
CHAPTER 4: INTERFACES Select “Se
Page 109 and 110:
CHAPTER 4: INTERFACES 4.3.4 Connect
Page 111 and 112:
CHAPTER 4: INTERFACES Note The fron
Page 113 and 114:
CHAPTER 4: INTERFACES 4.4.3 File Su
Page 115 and 116:
CHAPTER 4: INTERFACES Note The Open
Page 117 and 118:
CHAPTER 4: INTERFACES Note For fut
Page 119 and 120:
CHAPTER 4: INTERFACES Note Click F
Page 121 and 122:
CHAPTER 4: INTERFACES Enter the ap
Page 123 and 124:
CHAPTER 4: INTERFACES Click OK. Th
Page 125 and 126:
CHAPTER 4: INTERFACES 4.5 Upgrading
Page 127 and 128:
CHAPTER 4: INTERFACES Note Cycling
Page 129 and 130:
CHAPTER 4: INTERFACES The waveform
Page 131 and 132:
CHAPTER 4: INTERFACES The EnerVista
Page 133 and 134:
CHAPTER 4: INTERFACES With EnerVist
Page 135 and 136:
CHAPTER 4: INTERFACES 4.6.5 Event R
Page 137 and 138:
CHAPTER 4: INTERFACES • Active al
Page 139 and 140:
CHAPTER 4: INTERFACES 4.7 Using Ene
Page 141 and 142:
CHAPTER 4: INTERFACES FIGURE 4-13:
Page 143 and 144:
5.1 Overview Digital Energy Multili
Page 145 and 146:
CHAPTER 5: SETTINGS SETTINGS [ MES
Page 147 and 148:
CHAPTER 5: SETTINGS MESSAGE MESSAGE
Page 149 and 150:
CHAPTER 5: SETTINGS 5.1.3 Relay Ass
Page 151 and 152:
CHAPTER 5: SETTINGS 5.2.2 Preferenc
Page 153 and 154:
CHAPTER 5: SETTINGS bits, while par
Page 155 and 156:
CHAPTER 5: SETTINGS 5.2.4 Real Time
Page 157 and 158:
CHAPTER 5: SETTINGS 5.2.7 Clear Dat
Page 159 and 160:
CHAPTER 5: SETTINGS 5.3 S2 System S
Page 161 and 162:
CHAPTER 5: SETTINGS 5.3.2 Voltage S
Page 163 and 164:
CHAPTER 5: SETTINGS 5.3.5 Reduced V
Page 165 and 166:
CHAPTER 5: SETTINGS STARTER STATUS
Page 167 and 168:
CHAPTER 5: SETTINGS 5.4.2 Starter S
Page 169 and 170:
CHAPTER 5: SETTINGS These settings
Page 171 and 172:
CHAPTER 5: SETTINGS Vibration Switc
Page 173 and 174:
Page 175 and 176:
CHAPTER 5: SETTINGS Setting the INP
Page 177 and 178:
CHAPTER 5: SETTINGS Note 5.5.3 Forc
Page 179 and 180:
CHAPTER 5: SETTINGS TIME-SECONDS 40
Page 181 and 182:
CHAPTER 5: SETTINGS 5.6.3 Overload
Page 183 and 184:
CHAPTER 5: SETTINGS PICKUP (× FLA)
Page 185 and 186:
CHAPTER 5: SETTINGS Custom Overload
Page 187 and 188:
CHAPTER 5: SETTINGS Note TIME TO TR
Page 189 and 190:
Page 191 and 192:
CHAPTER 5: SETTINGS TIME TO TRIP (S
Page 193 and 194:
CHAPTER 5: SETTINGS TIME TO TRIP (S
Page 195 and 196:
CHAPTER 5: SETTINGS The following t
Page 197 and 198:
CHAPTER 5: SETTINGS This extra heat
Page 199 and 200:
CHAPTER 5: SETTINGS at a level that
Page 201 and 202:
CHAPTER 5: SETTINGS 5.7 S6 Current
Page 203 and 204:
CHAPTER 5: SETTINGS 5.7.4 Undercurr
Page 205 and 206: CHAPTER 5: SETTINGS Note 5.7.6 Grou
Page 207 and 208: CHAPTER 5: SETTINGS Note MESSAGE ME
Page 209 and 210: CHAPTER 5: SETTINGS 5.8.3 Jogging B
Page 211 and 212: CHAPTER 5: SETTINGS Note 5.8.4 Rest
Page 213 and 214: CHAPTER 5: SETTINGS 5.9.2 RTDs 1 to
Page 215 and 216: CHAPTER 5: SETTINGS 5.9.4 RTD 11 RT
Page 217 and 218: CHAPTER 5: SETTINGS 5.9.6 Open RTD
Page 219 and 220: CHAPTER 5: SETTINGS If the undervol
Page 221 and 222: CHAPTER 5: SETTINGS Note 5.10.4 Fre
Page 223 and 224: CHAPTER 5: SETTINGS 5.11.2 Power Fa
Page 225 and 226: CHAPTER 5: SETTINGS 5.11.4 Underpow
Page 227 and 228: CHAPTER 5: SETTINGS Note 5.11.7 Ove
Page 229 and 230: CHAPTER 5: SETTINGS 5.12.3 Demand t
Page 231 and 232: CHAPTER 5: SETTINGS 5.12.4 Pulse Ou
Page 233 and 234: CHAPTER 5: SETTINGS 5.13 S12 Analog
Page 235 and 236: CHAPTER 5: SETTINGS 5.13.2 Analog I
Page 237 and 238: CHAPTER 5: SETTINGS Note 5.13.3 Ana
Page 239 and 240: CHAPTER 5: SETTINGS This feature co
Page 241 and 242: CHAPTER 5: SETTINGS 5.14.2 Pre-Faul
Page 243 and 244: CHAPTER 5: SETTINGS 5.14.4 Test Out
Page 245 and 246: CHAPTER 5: SETTINGS 5.15 S14 Two-Sp
Page 247 and 248: CHAPTER 5: SETTINGS MESSAGE MESSAGE
Page 249 and 250: CHAPTER 5: SETTINGS 5.15.2 Speed2 U
Page 251 and 252: 6.1 Overview Digital Energy Multili
Page 253 and 254: CHAPTER 6: ACTUAL VALUES 6.1.2 Desc
Page 255: CHAPTER 6: ACTUAL VALUES 6.2.2 Moto
Page 259 and 260: CHAPTER 6: ACTUAL VALUES 6.2.5 Star
Page 261 and 262: CHAPTER 6: ACTUAL VALUES 6.3 A2 Met
Page 263 and 264: CHAPTER 6: ACTUAL VALUES 6.3.3 Volt
Page 265 and 266: CHAPTER 6: ACTUAL VALUES 6.3.6 Dema
Page 267 and 268: CHAPTER 6: ACTUAL VALUES FIGURE 6-1
Page 269 and 270: CHAPTER 6: ACTUAL VALUES The ACTUAL
Page 271 and 272: CHAPTER 6: ACTUAL VALUES The EnerVi
Page 273 and 274: CHAPTER 6: ACTUAL VALUES When the r
Page 275 and 276: CHAPTER 6: ACTUAL VALUES Pressing t
Page 277 and 278: CHAPTER 6: ACTUAL VALUES 6.4 A3 Lea
Page 279 and 280: CHAPTER 6: ACTUAL VALUES 6.4.4 Anal
Page 281 and 282: CHAPTER 6: ACTUAL VALUES 6.5.2 Gene
Page 283 and 284: CHAPTER 6: ACTUAL VALUES 6.6 A5 Eve
Page 285 and 286: CHAPTER 6: ACTUAL VALUES Underpower
Page 287 and 288: CHAPTER 6: ACTUAL VALUES 6.8 Diagno
Page 289 and 290: CHAPTER 6: ACTUAL VALUES forgotten,
Page 291 and 292: CHAPTER 6: ACTUAL VALUES PASSCODE
Page 293 and 294: 7.1 Overview Digital Energy Multili
Page 295 and 296: CHAPTER 7: TESTING 7.2 Hardware Fun
Page 297 and 298: CHAPTER 7: TESTING 7.2.4 GE Multili
Page 299 and 300: CHAPTER 7: TESTING APPLIED RESISTAN
Page 301 and 302: CHAPTER 7: TESTING ANALOG OUTPUT FO
Page 303 and 304: CHAPTER 7: TESTING 7.3 Additional F
Page 305 and 306: CHAPTER 7: TESTING Symmetrical comp
Page 307 and 308:
Digital Energy Multilin 469 Motor M
Page 309 and 310:
A: APPENDIX Once again, if the pola
Page 311 and 312:
A: APPENDIX • Programming the STA
Page 313 and 314:
A: APPENDIX HGF5C HGF8 808841A1 808
Page 315 and 316:
A: APPENDIX 808712A1.CDR 469 MOTOR
Page 317 and 318:
A: APPENDIX A.5 Change Notes A.5.1
Page 319 and 320:
A: APPENDIX PAG E (A3) PAG E (A4) T
Page 321 and 322:
CHAPTER I: Index Numerics 0 to 1mA
Page 323 and 324:
CHAPTER I: B BAUD RATE setpoints ..
Page 325 and 326:
CHAPTER I: pressure switch alarm ..
Page 327 and 328:
CHAPTER I: analog current .........
Page 329 and 330:
CHAPTER I: NAMEPLATE VOLTAGE.......
Page 331 and 332:
CHAPTER I: POWER FACTOR setpoints .
Page 333 and 334:
CHAPTER I: RTD BIAS curve .........
Page 335 and 336:
CHAPTER I: see 5 START BLOCK RELAY
Page 337 and 338:
CHAPTER I: U description...........
show all

Multilin 469 Motor Management Relay ... - GE Digital Energy

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?