Multilin 469 Motor Management Relay ... - GE Digital Energy
Multilin 469 Motor Management Relay ... - GE Digital Energy
Multilin 469 Motor Management Relay ... - GE Digital Energy
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
CHAPTER 6: ACTUAL VALUES<br />
• INVALID PASSCODE ENTERED: If an invalid passcode is entered for passcode security<br />
feature, this message will flash on the display.<br />
• INVALID SERVICE CODE ENTERED: This message appears if an invalid code is entered<br />
in S13 <strong>469</strong> TESTING <strong>GE</strong> MULTILIN USE ONLY.<br />
• KEY PRESSED HERE IS INVALID: Under certain situations, certain keys have no<br />
function (e.g. any number key while viewing Actual Values). If a key is pressed where it<br />
should have no function, this message will appear.<br />
• NEW PASSCODE HAS BEEN ACCEPTED: This message will appear as an acknowledge<br />
that the new passcode has been accepted when changing the passcode for the<br />
passcode security feature.<br />
• NEW settings HAS BEEN STORED: This message appear each time a settings has<br />
been altered and stored as shown on the display.<br />
• NO ALARMS: This message appears if an attempt is made to enter the A1 STATUS <br />
ALARM STATUS subgroup when there are no active alarms.<br />
• NO START BLOCKS ACTIVE: This message appears if an attempt is made to enter the<br />
A1 STATUS START BLOCKS subgroup when there are no active Start Blocks.<br />
• NO TRIPS OR ALARMS TO RESET: If RESET is pressed when there are no trips or alarms<br />
present, this message will appear.<br />
• OUT OF RAN<strong>GE</strong>! ENTER: #### - ##### by #: If an entered settings value that is<br />
outside of the acceptable range of values, the <strong>469</strong> displays this message, substituting<br />
the proper values for that settings. An appropriate value may then be entered.<br />
• PRESS [ENTER] TO ADD DEFAULT MESSA<strong>GE</strong>: If the ENTER key is pressed anywhere in<br />
the <strong>469</strong> actual value messages, this message prompts the user to press ENTER again<br />
to add a new default message. To add a new default message, ENTER must be<br />
pressed while this message is being displayed.<br />
• PRESS [ENTER] TO REMOVE MESSA<strong>GE</strong>: If the decimal key is pressed in the S1 <strong>469</strong> SETUP<br />
DEFAULT MESSA<strong>GE</strong>S settings group, immediately followed by the ENTER key, this<br />
message prompts the user to press enter to remove a default message. To remove the<br />
default message, ENTER must be pressed while this message is being displayed.<br />
• RESET PERFORMED SUCCESSFULLY: If all trip and alarm features that are active can<br />
be cleared (i.e. the conditions that caused these trips and/or alarms are no longer<br />
present), then this message will appear when a reset is performed, indicating that all<br />
trips and alarms have been cleared.<br />
• ROUNDED settings HAS BEEN STORED: A settings value entered with the numeric<br />
keypad may be between valid settings values. The <strong>469</strong> detects this condition and<br />
stores a value that has been rounded to the nearest valid settings value. To find the<br />
valid range and step for a given settings, simply press HELP while the settings is being<br />
displayed.<br />
• settings ACCESS IS NOW PERMITTED: This flash message notifies the user that<br />
settings may now be altered and stored any time the passcode security feature is<br />
enabled and a valid passcode is entered.<br />
• settings ACCESS IS NOW RESTRICTED: This message appears if the passcode security<br />
feature is enabled, a valid passcode has been entered, and the S1 <strong>469</strong> SETUP <br />
6–40 <strong>469</strong> MOTOR MANA<strong>GE</strong>MENT RELAY – INSTRUCTION MANUAL