Multilin 469 Motor Management Relay ... - GE Digital Energy
Multilin 469 Motor Management Relay ... - GE Digital Energy
Multilin 469 Motor Management Relay ... - GE Digital Energy
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
6.8.2 Flash Messages<br />
[.] KEY IS USED<br />
TO<br />
ADVANCE THE CUR-<br />
SOR<br />
ARE YOU SURE?<br />
PRESS<br />
[ENTER] TO VERIFY<br />
DEFAULT MESSA<strong>GE</strong><br />
HAS BEEN ADDED<br />
START BLOCK<br />
LOCKOUTS:<br />
OVERLOAD LOCKOUT<br />
BLOCK: 25 min<br />
CHAPTER 6: ACTUAL VALUES<br />
When the RESET has been pressed, the hot RTD condition is no longer present, and the<br />
lockout time has expired, the display will revert back to the normal Default Messages.<br />
Flash messages are warning, error, or general information messages that are temporarily<br />
displayed in response to certain key presses. These messages are intended to assist with<br />
navigation of the <strong>469</strong> messages by explaining what has happened or by prompting the<br />
user to perform certain actions.<br />
ACCESS DENIED,<br />
ENTER PASSCODE<br />
DATA CLEARED<br />
SUCCESSFULLY<br />
DEFAULT MESSA<strong>GE</strong><br />
HAS BEEN REMOVED<br />
END OF LIST END OF PA<strong>GE</strong><br />
INVALID PASSCODE<br />
ENTERED!<br />
NEW settings HAS<br />
BEEN STORED<br />
OUT OF RAN<strong>GE</strong>!<br />
ENTER:<br />
####-##### by #<br />
ROUNDED settings<br />
HAS BEEN STORED<br />
TIME ENTRY<br />
OUT OF RAN<strong>GE</strong><br />
INVALID SERVICE<br />
CODE ENTERED<br />
ACCESS DENIED,<br />
SHORT ACCESS<br />
SWITCH<br />
DATE ENTRY<br />
OUT OF RAN<strong>GE</strong><br />
DEFAULT MESSA<strong>GE</strong><br />
LIST IS FULL<br />
ENTER NEW PASS-<br />
CODE<br />
FOR ACCESS<br />
KEY PRESSED IS<br />
INVALID HERE<br />
NO ALARMS NO START BLOCKS<br />
ACTIVE<br />
PRESS [ENTER] TO<br />
ADD<br />
DEFAULT MESSA<strong>GE</strong><br />
settings ACCESS<br />
IS<br />
NOW PERMITTED<br />
TIME ENTRY WAS<br />
NOT COMPLETE<br />
PRESS [ENTER] TO<br />
REMOVE MESSA<strong>GE</strong><br />
settings ACCESS<br />
IS<br />
NOW RESTRICTED<br />
ALL POSSIBLE<br />
RESETS<br />
HAVE BEEN PER-<br />
FORMED<br />
DATE ENTRY WAS<br />
NOT COMPLETE<br />
DEFAULT MESSA<strong>GE</strong>S<br />
6 TO 20 ARE<br />
ASSIGNED<br />
INPUT FUNCTION<br />
ALREADY ASSIGNED<br />
NEW PASSCODE<br />
HAS BEEN ACCEPTED<br />
NO TRIPS OR<br />
ALARMS<br />
TO RESET<br />
RESET PERFORMED<br />
SUCCESSFULLY<br />
THIS FEATURE NOT<br />
PROGRAMMED<br />
TOP OF LIST TOP OF PA<strong>GE</strong><br />
• [.] KEY IS USED TO ADVANCE THE CURSOR: Any time a settings that requires text<br />
editing is viewed, this message will appear immediately to prompt the user to use the<br />
decimal key for cursor control. If the settings is not altered for one (1) minute, the<br />
message will flash again.<br />
• ACCESS DENIED, ENTER PASSCODE: The <strong>469</strong> has a passcode security feature. If that<br />
feature has been enabled, not only do the access switch terminals have to be shorted,<br />
but the passcode must also be entered. If the correct passcode has been lost or<br />
6–38 <strong>469</strong> MOTOR MANA<strong>GE</strong>MENT RELAY – INSTRUCTION MANUAL
Change language