final bid specs 09328.pdf - Freese and Nichols, Inc.

B. FLUSH-VALVES FOR WATER CLOSETS
1. Flush-Valve For Water Closets; Exposed type, chrome-plated, 1” supply inlet, screw
driver back-check angle stop, vacuum breaker, lever activating handle, solid ring pipe
support 1-1/2” top outlet spud with wall and spud flanges. Inlet of flush-valve shall be
11.1/2” maximum, above rim of water closet, coordinate flush valve location with grab
bars for accessible installations. Acceptable manufacturers and models: Sloan, Royal
III; Delany, 402-1.6 and Zurn, Z-6000-AV-WS-1.
C. SEATS FOR WATER CLOSETS:
1. Seat for Water Closets (WC): White, posture molded, elongated type, open front, extra
heavy construction, concealed check stainless steel hinges, and rubber bumpers.
Provide with antimicrobial agent option. Acceptable manufacturers and models:
Olsonite, 10CC; Church/Bemis, 1955C; Beneke, 527 or 533 and Kohler, K-4680-CA
series.
D. LAVATORIES
1. Lavatory (L1): Wall-mounted, white vitreous china, size 20” x 18”, holes for concealed
arms, front overflow, integral back, soap depression, and 8” center holes. Acceptable
manufacturers and models: American Standard, 0356.015; Eljer, 051-1848; Crane, 1-
412-S; Briggs, 6622; Zurn, Z5348; Kohler, K-2006.
E. FAUCETS FOR LAVATORIES
1. Faucet for Lavatories: Chrome-plated brass, 8” centers, soft flow vandal proof spout,
with chrome-plated brass wrist blades handles. Maximum flow is 2.20 GPM. Acceptable
manufacturers and models: Chicago Faucet, 404; T & S Brass, B-2680; Royal Brass, 41-
070-BH.4; Speakman, SC-3041-D75-LD and American Standard, 6500.000 with .102 H
Cross or .142 H Lever Handles; Kohler, K7443-3A – (4 Arm Handle), Cambridge/Delta
23T343; Symmons, S-244-LWG and Zurn, 831R4.
F. SUPPLIES AND STOPS FOR LAVATORIES
1. Supply and Stop for Lavatories: Supplied through the wall, chrome-plated cast brass
stop, 1/2” female standard pipe thread inlet by 3/8” O.D. compression type outlet angle
stop, wheel or four armed handle, 3/8” O.D. chrome-plated copper flexible riser, and wall
escutcheon. Acceptable manufacturers and models: McGuire, 2165LK; Eljer, American
Standard, Cambridge/Delta, Zurn and Engineered Brass (Just).
G. STRAINER AND TAILPIECE FOR LAVATORIES
1. Offset Strainer for Lavatories: 17 gauge chrome plated wheelchair strainer and tailpiece,
cast grid drain plug with strainer. Acceptable manufacturers and models: McGuire,
155WC;, Eljer, American Standard, Crane, Cambridge/Delta, Zurn and Engineered Brass
(Just).
H. P-TRAP FOR LAVATORIES
1. P-Trap for Lavatories: 17 gauge chrome-plated brass size 1-1/4”, integral cleanout, and
wall escutcheon. Acceptable manufacturers and models: McGuire, B8872; Eljer,
American Standard, Crane, Cambridge/Delta, Zurn and Engineered Brass (Just).
I. LAVATORY INSULATION KITS
1. Lavatory Insulation Kits: Fully molded closed cell vinyl insulation 3/16” thick with nylon
fasteners. K factor of 1.17 (ASTM C-177) self extinguishing burn characteristics (ASTM
D635). Insulation kit for p-trap, tailpiece, trap arm, hot and cold water supplies, white.
Acceptable manufacturers and models: Truebro Inc., #102 with accessory #105; Brocar
Products Inc., Plumberex, and TCI Products.
J. LAVATORY CARRIERS
1. Carrier for wall-mounted Lavatories mounted on walls other than concrete block: Wall
and floor supported type, compatible with specified lavatory, complete with adjustable
Plumbing Systems 22 00 01 - 6
DPR09328