final bid specs 09328.pdf - Freese and Nichols, Inc.

R. SUPPLIES AND STOPS FOR ELECTRIC WATER COOLERS
1. Supply and Stop for Electric Water Coolers (EWC_ & EWC_): Supplied through the wall,
chrome-plated brass, 1/2” female standard pipe thread inlet by 3/8” O.D. compression
type outlet angle stop, wheel or four-armed handle, with flexible riser and wall
escutcheon. . Acceptable manufacturers and models: McGuire, 2166LK; Eljer, American
Standard, Cambridge/Delta, Zurn and Engineered Brass (Just).
S. P-TRAP FOR ELECTRIC WATER COOLERS
1. P-Trap for Electrical Water Coolers (EWC_ & EWC_): 17 gauge chrome-plated brass,
size 1-1/4”, integral cleanout, and wall escutcheons. Acceptable manufacturers and
models: McGuire, B8912; Eljer, American Standard, Cambridge/Delta, Zurn and
Engineered Brass (Just).
T. ELECTRIC WATER COOLER CARRIERS
1. Carriers for Electric Water Coolers Mounted on Concrete Block Walls or Walls other than
Concrete Block: Wall and floor supported type, compatible with specified electric water
cooler, complete with adjustable through the wall frame including top and bottom hanger
plates, steel uprights, and block foot supports, and accessories. Acceptable
manufacturers and models: Josam, 17900; Jay R. Smith, 830; Tyler/Wade, W400-AM11;
HAWS, 6800; MC-33 (Bi-Level type); and Zurn, Z-1225.
U. EMERGENCYEYEWASH UNITS
1. Emergency eyewash unit: Exposed type with floor flange, all stainless steel construction,
large stainless steel bowl and two soft stream heads actuated by stay open ball valve
with push-flag. Pipe sizes shall be 1/2” water inlet and 1-1/4” drain. Provide Hot and Cold
water temperature mixing valve. Acceptable manufacturers: Speakman, Haws, Guardian
and Bradley.
V. SERVICE SINKS
1. Service Sink (SSK1): Floor-mounted, molded polyester or fiberglass material, size 24” x
24” x 10”, 3” drain, with mop hanger, hose and hose bracket, vinyl bumperguard,
removable combination dome strainer and stainless steel lint basket, and black on white
marbleized color. Acceptable manufacturers and models: Florestone, MSR-2424;
Florestone, (Hose & Bracket), MR-370; Florestone (Mop Hanger), MR-372; Florestone
(Wall Guard), MR-377 (24”); Fiat (Basin), MSB 2424; Fiat (Hose & Bracket), 832-AA; Fiat
(Mop Hanger), 889-CC; Fiat (Wall Guard), MSG 2424; Mustee (Basin) 63; Mustee (Hose
& Bracket), 65.700; Mustee (Mop Hanger), 65.600; Swan (Basin), MS-2424; Swan (Hose
& Bracket), MS-2405, Swan (Mop Hanger), MS 2437; Stern/Williams (Basin), MTB-2424;
Stern/Williams (Hose & Bracket) T-35, Stern/Williams (Mop Hanger), T-40 and Zurn 1996
(24 x 24) with accessories.
W. FLOOR DRAINS
1. Floor drain (FD) (For use in Finished Floors without square tile): ANSI A112.21.1; cast
iron body, double drainage flange, weepholes, bottom outlet, vandal proof secured 6" dia.
nickel bronze adjustable flat strainer, and non-puncturing flashing collar. Provide with trap
primer connection adapter if trap primers are used for the floor drain.
X. TRENCH DRAINS
ACCEPTABLE MANUFACTURERS AND MODELS
Josam Series 30000-6A
Jay R. Smith Series 2005 or 2010
Wade Series W-1100
Zurn Series Z-415
Mifab Series F-1100
1. Trench drain (TD): Modular precast polymer concrete, sloped or neutral, interlocking
channels with positive seal, tongue and groove interlocking joints. Channels shall be
Plumbing Systems 22 00 01 - 8
DPR09328