final bid specs 09328.pdf - Freese and Nichols, Inc.

through the wall frame including steel uprights, block foot supports, concealed arms, and
accessories. Verify that base plate for carrier specified will fit within wall space provided.
Acceptable manufacturers and models: Zurn, Z-1231 or Z-1231-D Series (3” deep base
plates); Jay R. Smith, 700 Series (4” deep base plates); Tyler/Wade, W520 (4 ¼” deep
base plates) and Josam, 17100 & 17105 Series (4” deep base plates); Josam, 17570
(For corner lavatory); Mifab, MC-31-C.
K. SINKS
1. Sink: Countertop mounted, single compartment, 18-gauge stainless steel, self rimming,
faucet deck, with three (3) 1-1/2” diameter holes, 4” centers, with undercoated underside.
Size 25” x 21-1/4” x 5-3/8” deep. Acceptable manufacturers and models: Elkay, LRAD
2521 (or 2521L) and Just, SL-ADA-2125-A-GR -L or R.
L. FAUCETS FOR SINKS
1. Faucets for Sinks): Chrome-plated brass, deck mount, 8” centers, swing gooseneck soft
flow spout with 8”-9” reach (centerline of spout inlet to centerline of spout outlet), and
chrome-plated brass 4” wrist blade handles. Maximum flow is 2.20 GPM. Acceptable
manufacturers and models: Chicago Faucet, 201-GN8A-E3-317; T & S Brass, B-2867-
00(B-WH-4); Royal Brass, 401-G98-AW; Speakman, SC-3004-8-LD; American Standard,
7230.000 with .372H handles, Cambridge/Delta 27T2944 with 76860-5 spout and Zurn,
Z-831B4.
M. SUPPLIES AND STOPS FOR SINKS
1. Supply and Stop for Sinks: Supplied through the wall, chrome-plated cast brass stop,
1/2” female standard pipe thread inlet by 3/8” O.D. compression type outlet angle stop,
wheel or four armed handle, 3/8” O.D. chrome-plated copper flexible riser, and wall
escutcheon. Acceptable manufacturers and models: McGuire, 2165LK; Eljer, American
Standard, Cambridge/Delta, Zurn and Engineered Brass (Just).
N. STRAINER AND TAILPIECE FOR SINKS
1. Offset Strainer for Sinks (S_ & S _): 17 gauge chrome plated wheelchair strainer and
tailpiece, cast grid drain plug with strainer. Acceptable manufacturers and models:
McGuire, 1149WC or PW1149WC (includes pre-wrapped insulation); Eljer, American
Standard, Crane, Cambridge/Delta, Zurn and Engineered Brass (Just).
2. 1A and Orion, WA Series.
O. P-TRAPS FOR SINKS
1. P-Trap for Sinks): Chrome-plated, 17 gauge cast brass, size 1-1/2”, with integral
cleanout, and wall escutcheon. Acceptable manufacturers and models: McGuire,
B8912; Eljer, American Standard, Crane, Cambridge/Delta, Zurn and Engineered Brass
(Just).
P. INSULATION KIT FOR ACCESSIBLE SINKS
1. Sink Insulation Kits: Fully molded closed cell vinyl insulation 3/16” thick with nylon
fasteners. K factor of 1.17 (ASTM C-177) self extinguishing burn characteristics (ASTM
D635). Insulation kit for p-trap, tailpiece, trap arm, hot and cold water supplies, white.
Acceptable manufacturers and models: Truebro Inc., #102 with accessory #105; Brocar
Products Inc., Plumberex, TCI Products. Insulation kit is not required if a trap/supplies
enclosure is provided under another division.
Q. ELECTRIC WATER COOLERS
1. Electric Water Cooler (EWC1): Wall-mounted, bi-level, wheelchair type, front and sides
push bars, stainless steel top, stainless steel cabinet with a flexible hooded bubbler.
Wheelchair unit shall be mounted up +36” to top of bubbler. Water cooler shall deliver
7.5 GPH minimum of 50°F water, based upon 80°F inlet water temperature and 90°F
ambient air temperature. Acceptable manufacturers and models: Elkay, EZSTL-8C;
Haws, HWUACO8L; Halsey Taylor, HAC8FSBL-Q; Oasis, PR8ACSL; Acorn A112108F
and Sunroc, ADA-D8-BL. Provide with optional apron mounted to bottom of higher unit.
Plumbing Systems 22 00 01 - 7
DPR09328