final bid specs 09328.pdf - Freese and Nichols, Inc.

More documents

Recommendations

Info

5. Test each motor for proper phase rotation. 6. Perform each electrical test and visual and mechanical inspection stated in NETA Acceptance Testing Specification. Certify compliance with test parameters. 7. Correct malfunctioning units on-site, where possible, and retest to demonstrate compliance; otherwise, replace with new units and retest. D. Enclosed controllers will be considered defective if they do not pass tests and inspections. E. Prepare test and inspection reports including a certified report that identifies enclosed controllers and that describes scanning results. Include notation of deficiencies detected, remedial action taken and observations after remedial action. 3.06 ADJUSTING A. Set field-adjustable switches, auxiliary relays, time-delay relays, timers, and overload-relay pickup and trip ranges. B. Adjust overload-relay heaters or settings if power factor correction capacitors are connected to the load side of the overload relays. C. Adjust the trip settings of MCPs and thermal-magnetic circuit breakers with adjustable instantaneous trip elements. Initially adjust to six times the motor nameplate full-load ampere ratings and attempt to start motors several times, allowing for motor cool-down between starts. If tripping occurs on motor inrush, adjust settings in increments until motors start without tripping. Do not exceed eight times the motor full-load amperes (or 11 times for NEMA Premium Efficient motors if required). Where these maximum settings do not allow starting of a motor, notify Owner/Contractor before increasing settings. D. Set field-adjustable circuit-breaker trip ranges. 3.07 PROTECTION A. Temporary Heating: Apply temporary heat to maintain temperature according to manufacturer's written instructions until enclosed controllers are ready to be energized and placed into service. B. Replace controllers whose interiors have been exposed to water or other liquids prior to Substantial Completion. END OF SECTION Enclosed Controllers 26 29 13 - 9 DRP09328
26 41 13 LIGHTNING PROTECTION FOR STRUCTURES 1.00 GENERAL 1.01 WORK INCLUDED Furnish labor, design, materials, equipment and incidentals necessary to install a complete lightning protection system in accordance with UL 96A, NFPA 780, and this specification for protection of the Parks and Recreation Facility at the Stevens Park site. Lightning protection system shall be tied to existing and new grounding system as required. 1.02 QUALITY ASSURANCE A. The system furnished under this specification shall be the standard product of a manufacturer regularly engaged in the production of lightning protection systems and shall be the manufacturer's latest approved design. Listing of the manufacturer in the lightning protection section of the current edition of Underwriters' Laboratories, Inc., Electrical Construction Materials List will be accepted as compliance with this requirement. B. All materials shall be copper and bronze and of the size, weight and construction to suit the application where used in accordance with UL, NFPA, NEC code requirements for this type structure and as per manufacturer's recommendations. Class I sized components may be utilized on roof levels 75 feet and below in height. Class II sized components are required for roof levels over 75 feet in height. 1.03 SUBMITTALS A. Submittals shall be in accordance with Section 01 33 00, SUBMITTALS, and shall include: 1. Specifications 2. Catalog Sheets for All Products Provided 3. Shop drawings showing type, size and location of all equipment, grounds, cable routings, etc. 4. Continuity Test Report 5. Copy of U.L. Master Label for the Facility 1.04 STANDARDS AND REFERENCES A. Refer to Section 26 05 00, COMMON WORK RESULTS FOR ELECTRICAL, for all standards which apply to this section. NFPA 780 Standard for the Installation of Lightning Protection Systems UL 96A LPI 175 Standard for Installation Requirements for Lightning Protection Systems Lightning Protection Institute Standard of Practice Lightning Protection For Structures 26 41 13-1 DRP09328
Page 2 and 3:
STEVENS PARK GOLF COURCE MAINTENANC
Page 4 and 5:
26 24 16 Lighting and Branch Panelb
Page 6 and 7:
B. Manufacturer Qualifications: A f
Page 8 and 9:
1. For concrete surfaces exposed to
Page 10 and 11:
k. Rich Seal 18 percent E; Richmond
Page 12 and 13:
2.13 FABRICATING REINFORCEMENT A. F
Page 14 and 15:
placing concrete, taking precaution
Page 16 and 17:
F. Cold-Weather Placement: Comply w
Page 18 and 19:
D. Unformed Surfaces: Begin curing
Page 20 and 21:
2. Slump: ASTM C 143; one test at p
Page 22 and 23:
C. Determination of Average Strengt
Page 24 and 25:
Attachment B Documentation of Avera
Page 26 and 27:
B. LEED Submittal: 1. Product Data
Page 28 and 29:
2.03 NON-LOAD-BEARING WALL FRAMING
Page 30 and 31:
3. Fasten cold-formed metal framing
Page 32 and 33:
3. Bridging: Combination of flat, t
Page 34 and 35:
C. Mill Certificates: Signed by man
Page 36 and 37:
the load imposed when installed in
Page 38 and 39:
A. Fabricate metal bollards from Sc
Page 40 and 41:
06 10 00 ROUGH CARPENTRY 1.00 GENER
Page 42 and 43:
C. For concealed boards, provide lu
Page 44 and 45:
06 40 23 INTERIOR ARCHITECTURAL WOO
Page 46 and 47:
2.02 MATERIALS A. General: Provide
Page 48 and 49:
1. Trial fit assemblies at fabricat
Page 50 and 51:
2. Secure backsplashes to tops with
Page 52 and 53:
. Marlite. c. Nudo Products, Inc. 2
Page 54 and 55:
07 92 00 JOINT SEALANTS 1.00 GENERA
Page 56 and 57:
a. For joints with dissimilar subst
Page 58 and 59:
o. Pecora Corporation; 865. p. Peco
Page 60 and 61:
2.04 JOINT-SEALANT BACKING A. Gener
Page 62 and 63:
5. Provide recessed joint configura
Page 64 and 65:
08 11 13 HOLLOW METAL DOORS AND FRA
Page 66 and 67:
2.02 MATERIALS 5. Security Metal Pr
Page 68 and 69:
D. Hollow Metal Frames: Where frame
Page 70 and 71:
f. Check plumbness, squareness, and
Page 72 and 73:
C. Forest Certification: Provide do
Page 74 and 75:
2.04 FABRICATION A. Factory machine
Page 76 and 77:
08 33 23 OVERHEAD COILING DOORS 1.0
Page 78 and 79:
ASTM A 123/A 123M. Slot bolt holes
Page 80 and 81:
08 71 00 DOOR HARDWARE 1.00 GENERAL
Page 82 and 83:
C. Deliver keys to manufacturer of
Page 84 and 85:
2.04 LOCKS AND LATCHES, GENERAL A.
Page 86 and 87:
2.09 KEYING 3. ASSA, Inc.; an ASSA
Page 88 and 89:
14. Rixson Specialty Door Controls;
Page 90 and 91:
B. Examine roughing-in for electric
Page 92 and 93:
1 each Drip Cap NGP 16A Door Hardwa
Page 94 and 95:
D. Bituminous Paint: Cold-applied a
Page 96 and 97:
09 22 16 NON-STRUCTURAL METAL FRAMI
Page 98 and 99:
C. Firestop Tracks: Top runner manu
Page 100 and 101:
F. Installation Tolerances: Install
Page 102 and 103:
1.06 PROJECT CONDITIONS A. Environm
Page 104 and 105:
B. Steel Drill Screws: ASTM C 1002,
Page 106 and 107:
C. Interior Trim: Install in the fo
Page 108 and 109:
09 51 13 ACOUSTICAL PANEL CEILINGS
Page 110 and 111:
D. Wire Hangers, Braces, and Ties:
Page 112 and 113:
09 65 13 RESILIENT BASE AND ACCESSO
Page 114 and 115:
G. Inside Corners: Job formed. H. F
Page 116 and 117:
2. Sweep and vacuum surfaces thorou
Page 118 and 119:
1. Critical Radiant Flux Classifica
Page 120 and 121:
4. Moisture Testing: Perform tests
Page 122 and 123:
09 91 13 EXTERIOR PAINTING 1.00 GEN
Page 124 and 125:
2.04 METAL PRIMERS A. Alkyd Anticor
Page 126 and 127:
3.03 APPLICATION A. Apply paints ac
Page 128 and 129:
09 91 23 INTERIOR PAINTING 1.00 0BG
Page 130 and 131:
B. 35BChemical Components of Field-
Page 132 and 133:
3.02 18BPREPARATION A. 5BComply wit
Page 134 and 135:
3.05 21BINTERIOR PAINTING SCHEDULE
Page 136 and 137:
2. Manufacturer's Information: Manu
Page 138 and 139:
D. Material Compatibility: Provide
Page 140 and 141:
sticky under moderate thumb pressur
Page 142 and 143:
10 28 00 TOILET, BATH AND LAUNDRY A
Page 144 and 145:
1. Plumberex Specialty Products, In
Page 146 and 147:
B. Aluminum: Alloy and temper recom
Page 148 and 149:
2.05 ALUMINUM FINISHES A. Color Ano
Page 150 and 151:
10 44 16 FIRE EXTINGUISHERS 1.00 GE
Page 152 and 153:
3.02 INSTALLATION A. General: Insta
Page 154 and 155:
1.04 SYSTEM DESCRIPTION A. General:
Page 156 and 157:
8. Accessories. B. Shop Drawings: F
Page 158 and 159:
1.07 QUALITY ASSURANCE A. Erector Q
Page 160 and 161:
1.11 WARRANTY A. Special Warranty o
Page 162 and 163:
N. Primer: SSPC-Paint 15, Type I, r
Page 164 and 165:
. Join flanges to webs of built-up
Page 166 and 167:
2. Panel Coverage: 36 inches (914 m
Page 168 and 169:
2. Clips: Manufacturer's standard,
Page 170 and 171:
d. Radiographic Inspection: ASTM E
Page 172 and 173:
3.04 METAL PANEL INSTALLATION, GENE
Page 174 and 175:
3.07 TRANSLUCENT PANEL INSTALLATION
Page 176 and 177:
2. Expansion Provisions: Provide fo
Page 178 and 179:
3.15 DEMONSTRATION A. Engage a fact
Page 180 and 181:
3. Fire alarm signal shall initiate
Page 182 and 183:
E. Electrical Components, Devices,
Page 184 and 185:
2.03 MANUAL FIRE ALARM BOXES A. Des
Page 186 and 187:
72 4-4 “Visible Characteristics,
Page 188 and 189:
21 11 00 FACILITY FIRE SUPRESSION W
Page 190 and 191:
1.05 JOB CONDITIONS A. The fire pro
Page 192 and 193:
D. Install piping to allow for expa
Page 194 and 195:
21 13 13 DRY-PIPE SPRINKLER SYSTEMS
Page 196 and 197:
2.00 PRODUCTS 2.01 MATERIALS A. SPR
Page 198 and 199:
22 00 01 PLUMBING SYSTEMS 1.00 GENE
Page 200 and 201:
2.00 PRODUCTS 2.01 PIPE AND FITTING
Page 202 and 203:
3. CPVC and PVC Butterfly valves: 1
Page 204 and 205:
through the wall frame including st
Page 206 and 207:
presloped with a minimum .06% slope
Page 208 and 209:
ACCEPTABLE MANUFACTURERS ProVent Sy
Page 210 and 211:
V. SAND AND SOILDS INTERCEPTORS 1.
Page 212 and 213:
3.00 EXECUTION pattern is not obvio
Page 214 and 215:
the public from open trenches. Erec
Page 216 and 217:
23 00 00 BASIC MECHANICAL MATERIALS
Page 218 and 219:
D. Plastic, Pipe-Flange Gasket, Bol
Page 220 and 221:
E. Place grout, completely filling
Page 222 and 223:
d. Other design parameters such as
Page 224 and 225:
23 05 93 TESTING, ADJUSTING, AND BA
Page 226 and 227:
G. Examine HVAC system and equipmen
Page 228 and 229:
a. Measure outlet static pressure a
Page 230 and 231:
3.10 TEMPERATURE-CONTROL VERIFICATI
Page 232 and 233:
B. Seasonal Periods: If initial TAB
Page 234 and 235:
1.07 SCHEDULING A. Schedule insulat
Page 236 and 237:
K. Insulation Terminations: For ins
Page 238 and 239:
1. Material: Mineral-fiber blanket.
Page 240 and 241:
2.00 PRODUCTS 2.01 MANUFACTURERS A.
Page 242 and 243:
M. Insulation Terminations: For ins
Page 244 and 245:
3.09 INTERIOR INSULATION APPLICATIO
Page 246 and 247:
B. Galvanized Sheet Steel: Lock-for
Page 248 and 249:
D. Install couplings tight to duct
Page 250 and 251:
E. Mechanical Cleaning Methodology:
Page 252 and 253:
2. Roll-Formed Steel Blades: 0.064-
Page 254 and 255:
23 34 23 POWER VENTILATORS 1.00 GEN
Page 256 and 257:
3. Propeller Fans: a. Aerovent; a T
Page 258 and 259:
2.05 MOTORS A. Refer to Division 23
Page 260 and 261:
23 37 13 DIFFUSERS, REGISTERS, AND
Page 262 and 263:
23 81 26 SPLIT-SYSTEM AIR-CONDITION
Page 264 and 265:
will occur as a result of overflow
Page 266 and 267:
B. Verify that units are installed
Page 268 and 269:
2.05 FAN terminal box. Fin surface
Page 270 and 271:
26 05 00 COMMON WORK RESULTS FOR EL
Page 272 and 273:
1.05 DELIVERY AND STORAGE A. Follow
Page 274 and 275:
D. All construction areas shall be
Page 276 and 277:
B. SINGLE CONDUCTORS: Conductor wit
Page 278 and 279:
26 05 19.01 WIRE CONNECTIONS AND DE
Page 280 and 281:
26 05 26 GROUNDING & BONDING FOR EL
Page 282 and 283:
G. Metal conduits stubbed up into s
Page 284 and 285: 26 05 29 HANGERS AND SUPPORTS FOR E
Page 286 and 287: B. Maximum Support Spacing and Mini
Page 288 and 289: 26 05 33.01 CONDUITS 1.00 GENERAL 1
Page 290 and 291: O. THREADED NIPPLES: As manufacture
Page 292 and 293: 2. Grade underground and outdoor co
Page 294 and 295: 26 05 33.02 WIREWAYS 1.00 GENERAL 1
Page 296 and 297: C. Unless otherwise noted, location
Page 298 and 299: C. PULL AND JUNCTION BOXES: Metal c
Page 300 and 301: 2. Provide conductor tags for condu
Page 302 and 303: 1. Color-Coding for Phase Identific
Page 304 and 305: NO TEXT FOR THIS PAGE Identificatio
Page 306 and 307: 5. A relay coordination study shall
Page 308 and 309: 2.00 EXECUTION 2.01 GENERAL A. Prov
Page 310 and 311: B. The CONTRACTOR shall adjust all
Page 312 and 313: 26 09 23 LIGHTING CONTROL DEVICES 1
Page 314 and 315: F. A dedicated photocell input shal
Page 316 and 317: 26 24 16 LIGHTING AND BRANCH PANELB
Page 318 and 319: D. Each circuit breaker used in 208
Page 320 and 321: 26 27 26 WIRING DEVICES 1.00 GENERA
Page 322 and 323: A. Comply with NECA 1, including th
Page 324 and 325: 26 28 16 ENCLOSED SWITCHES AND CIRC
Page 326 and 327: 26 29 13 ENCLOSED CONTROLLERS 1.00
Page 328 and 329: D. CONTROL POWER: Control power sha
Page 330 and 331: H. Wiring in the combination starte
Page 332 and 333: B. IEC or dual rated NEMA/IEC equip
Page 336 and 337: 2.00 PRODUCTS 2.01 MATERIALS A. Mat
Page 338 and 339: 3.02 FIELD QUALITY CONTROL A. The l
Page 340 and 341: D. LAMPS 1. FLUORESCENT: Cool white
Page 342 and 343: 31 23 10 STRUCTURAL EXCAVATION AND
Page 344 and 345: 3.00 EXECUTION 3.01 PREPARATION Cle
Page 346: 3. Areas of the fill being compacte
show all

final bid specs 09328.pdf - Freese and Nichols, Inc.

Create successful ePaper yourself

Delete template?

Save as template?