final bid specs 09328.pdf - Freese and Nichols, Inc.

More documents

Recommendations

Info

5. Provide recessed joint configuration of recess depth and at locations indicated per Figure 5C in ASTM C 1193. 6. Use masking tape to protect surfaces adjacent to recessed tooled joints. 3.04 FIELD QUALITY CONTROL A. Field-Adhesion Testing: Field test joint-sealant adhesion to joint substrates as follows: 1. Extent of Testing: Test completed elastomeric sealant joints as follows: 2. Perform 4 tests for each type of elastomeric sealant and joint substrate. 3. Test Method: Test joint sealants according to Method A, Field-Applied Sealant Joint Hand Pull Tab in Appendix X1 in ASTM C 1193. 4. For joints with dissimilar substrates, verify adhesion to each substrate separately; do this by extending cut along one side, verifying adhesion to opposite side. Repeat procedure for opposite side. 5. Repair sealants pulled from test area by applying new sealants following same procedures used originally to seal joints. Ensure that original sealant surfaces are clean and that new sealant contacts original sealant. B. Evaluation of Field Test Results: Sealants not evidencing adhesive failure from testing or noncompliance with other indicated requirements will be considered satisfactory. Remove sealants that fail to adhere to joint substrates during testing or to comply with other requirements. Retest failed applications until test results prove sealants comply with indicated requirements. 3.05 CLEANING A. Clean off excess sealant or sealant smears adjacent to joints as the Work progresses by methods and with cleaning materials approved in writing by manufacturers of joint sealants and of products in which joints occur. 3.06 PROTECTION A. Protect joint sealants during and after curing period from contact with contaminating substances and from damage resulting from construction operations or other causes so sealants are without deterioration or damage at time of Substantial Completion. If, despite such protection, damage or deterioration occurs, cut out and remove damaged or deteriorated joint sealants immediately so installations with repaired areas are indistinguishable from original work. 3.07 JOINT-SEALANT SCHEDULE A. Joint-Sealant Application: Exterior vertical and horizontal nontraffic construction joints in cast-in-place concrete. Colors are to match the material being sealed. 1. Joint Sealant: Multicomponent nonsag neutral-curing silicone sealant, Multicomponent nonsag immersible urethane sealant or Single-component nonsag urethane sealant. B. Joint-Sealant Application: Exterior vertical joints between different materials listed above. 1. Joint Sealant: Single-component neutral- and basic-curing silicone sealant,Singlecomponent nonsag urethane sealant. C. Joint-Sealant Application: Exterior perimeter joints between metal panels and frames of doorsand louvers. Joint Sealants 07 92 00 - 9 DPR09328
1. Joint Sealant: Single-component neutral- and basic-curing silicone sealant,Multicomponent nonsag urethane sealant or Single-component nonsag urethane sealant. D. Joint-Sealant Application: Vertical control and expansion joints on exposed interior surfaces of exterior walls. 1. Joint Sealant: Single-component neutral-curing silicone sealant or Multicomponent nonsag urethane sealant or. E. Joint-Sealant Application: Interior perimeter joints of exterior openings. 1. Joint Sealant: Single-component neutral- and basic-curing silicone sealant or Multicomponent nonsag urethane sealant. 2. . F. Joint-Sealant Application Perimeter joints between interior wall surfaces and frames of interior doors and windows. 1. Joint Sealant: Latex sealant. END OF SECTION Joint Sealants 07 92 00 - 10 DPR09328
Page 2 and 3:
STEVENS PARK GOLF COURCE MAINTENANC
Page 4 and 5:
26 24 16 Lighting and Branch Panelb
Page 6 and 7:
B. Manufacturer Qualifications: A f
Page 8 and 9:
1. For concrete surfaces exposed to
Page 10 and 11:
k. Rich Seal 18 percent E; Richmond
Page 12 and 13: 2.13 FABRICATING REINFORCEMENT A. F
Page 14 and 15: placing concrete, taking precaution
Page 16 and 17: F. Cold-Weather Placement: Comply w
Page 18 and 19: D. Unformed Surfaces: Begin curing
Page 20 and 21: 2. Slump: ASTM C 143; one test at p
Page 22 and 23: C. Determination of Average Strengt
Page 24 and 25: Attachment B Documentation of Avera
Page 26 and 27: B. LEED Submittal: 1. Product Data
Page 28 and 29: 2.03 NON-LOAD-BEARING WALL FRAMING
Page 30 and 31: 3. Fasten cold-formed metal framing
Page 32 and 33: 3. Bridging: Combination of flat, t
Page 34 and 35: C. Mill Certificates: Signed by man
Page 36 and 37: the load imposed when installed in
Page 38 and 39: A. Fabricate metal bollards from Sc
Page 40 and 41: 06 10 00 ROUGH CARPENTRY 1.00 GENER
Page 42 and 43: C. For concealed boards, provide lu
Page 44 and 45: 06 40 23 INTERIOR ARCHITECTURAL WOO
Page 46 and 47: 2.02 MATERIALS A. General: Provide
Page 48 and 49: 1. Trial fit assemblies at fabricat
Page 50 and 51: 2. Secure backsplashes to tops with
Page 52 and 53: . Marlite. c. Nudo Products, Inc. 2
Page 54 and 55: 07 92 00 JOINT SEALANTS 1.00 GENERA
Page 56 and 57: a. For joints with dissimilar subst
Page 58 and 59: o. Pecora Corporation; 865. p. Peco
Page 60 and 61: 2.04 JOINT-SEALANT BACKING A. Gener
Page 64 and 65: 08 11 13 HOLLOW METAL DOORS AND FRA
Page 66 and 67: 2.02 MATERIALS 5. Security Metal Pr
Page 68 and 69: D. Hollow Metal Frames: Where frame
Page 70 and 71: f. Check plumbness, squareness, and
Page 72 and 73: C. Forest Certification: Provide do
Page 74 and 75: 2.04 FABRICATION A. Factory machine
Page 76 and 77: 08 33 23 OVERHEAD COILING DOORS 1.0
Page 78 and 79: ASTM A 123/A 123M. Slot bolt holes
Page 80 and 81: 08 71 00 DOOR HARDWARE 1.00 GENERAL
Page 82 and 83: C. Deliver keys to manufacturer of
Page 84 and 85: 2.04 LOCKS AND LATCHES, GENERAL A.
Page 86 and 87: 2.09 KEYING 3. ASSA, Inc.; an ASSA
Page 88 and 89: 14. Rixson Specialty Door Controls;
Page 90 and 91: B. Examine roughing-in for electric
Page 92 and 93: 1 each Drip Cap NGP 16A Door Hardwa
Page 94 and 95: D. Bituminous Paint: Cold-applied a
Page 96 and 97: 09 22 16 NON-STRUCTURAL METAL FRAMI
Page 98 and 99: C. Firestop Tracks: Top runner manu
Page 100 and 101: F. Installation Tolerances: Install
Page 102 and 103: 1.06 PROJECT CONDITIONS A. Environm
Page 104 and 105: B. Steel Drill Screws: ASTM C 1002,
Page 106 and 107: C. Interior Trim: Install in the fo
Page 108 and 109: 09 51 13 ACOUSTICAL PANEL CEILINGS
Page 110 and 111: D. Wire Hangers, Braces, and Ties:
Page 112 and 113:
09 65 13 RESILIENT BASE AND ACCESSO
Page 114 and 115:
G. Inside Corners: Job formed. H. F
Page 116 and 117:
2. Sweep and vacuum surfaces thorou
Page 118 and 119:
1. Critical Radiant Flux Classifica
Page 120 and 121:
4. Moisture Testing: Perform tests
Page 122 and 123:
09 91 13 EXTERIOR PAINTING 1.00 GEN
Page 124 and 125:
2.04 METAL PRIMERS A. Alkyd Anticor
Page 126 and 127:
3.03 APPLICATION A. Apply paints ac
Page 128 and 129:
09 91 23 INTERIOR PAINTING 1.00 0BG
Page 130 and 131:
B. 35BChemical Components of Field-
Page 132 and 133:
3.02 18BPREPARATION A. 5BComply wit
Page 134 and 135:
3.05 21BINTERIOR PAINTING SCHEDULE
Page 136 and 137:
2. Manufacturer's Information: Manu
Page 138 and 139:
D. Material Compatibility: Provide
Page 140 and 141:
sticky under moderate thumb pressur
Page 142 and 143:
10 28 00 TOILET, BATH AND LAUNDRY A
Page 144 and 145:
1. Plumberex Specialty Products, In
Page 146 and 147:
B. Aluminum: Alloy and temper recom
Page 148 and 149:
2.05 ALUMINUM FINISHES A. Color Ano
Page 150 and 151:
10 44 16 FIRE EXTINGUISHERS 1.00 GE
Page 152 and 153:
3.02 INSTALLATION A. General: Insta
Page 154 and 155:
1.04 SYSTEM DESCRIPTION A. General:
Page 156 and 157:
8. Accessories. B. Shop Drawings: F
Page 158 and 159:
1.07 QUALITY ASSURANCE A. Erector Q
Page 160 and 161:
1.11 WARRANTY A. Special Warranty o
Page 162 and 163:
N. Primer: SSPC-Paint 15, Type I, r
Page 164 and 165:
. Join flanges to webs of built-up
Page 166 and 167:
2. Panel Coverage: 36 inches (914 m
Page 168 and 169:
2. Clips: Manufacturer's standard,
Page 170 and 171:
d. Radiographic Inspection: ASTM E
Page 172 and 173:
3.04 METAL PANEL INSTALLATION, GENE
Page 174 and 175:
3.07 TRANSLUCENT PANEL INSTALLATION
Page 176 and 177:
2. Expansion Provisions: Provide fo
Page 178 and 179:
3.15 DEMONSTRATION A. Engage a fact
Page 180 and 181:
3. Fire alarm signal shall initiate
Page 182 and 183:
E. Electrical Components, Devices,
Page 184 and 185:
2.03 MANUAL FIRE ALARM BOXES A. Des
Page 186 and 187:
72 4-4 “Visible Characteristics,
Page 188 and 189:
21 11 00 FACILITY FIRE SUPRESSION W
Page 190 and 191:
1.05 JOB CONDITIONS A. The fire pro
Page 192 and 193:
D. Install piping to allow for expa
Page 194 and 195:
21 13 13 DRY-PIPE SPRINKLER SYSTEMS
Page 196 and 197:
2.00 PRODUCTS 2.01 MATERIALS A. SPR
Page 198 and 199:
22 00 01 PLUMBING SYSTEMS 1.00 GENE
Page 200 and 201:
2.00 PRODUCTS 2.01 PIPE AND FITTING
Page 202 and 203:
3. CPVC and PVC Butterfly valves: 1
Page 204 and 205:
through the wall frame including st
Page 206 and 207:
presloped with a minimum .06% slope
Page 208 and 209:
ACCEPTABLE MANUFACTURERS ProVent Sy
Page 210 and 211:
V. SAND AND SOILDS INTERCEPTORS 1.
Page 212 and 213:
3.00 EXECUTION pattern is not obvio
Page 214 and 215:
the public from open trenches. Erec
Page 216 and 217:
23 00 00 BASIC MECHANICAL MATERIALS
Page 218 and 219:
D. Plastic, Pipe-Flange Gasket, Bol
Page 220 and 221:
E. Place grout, completely filling
Page 222 and 223:
d. Other design parameters such as
Page 224 and 225:
23 05 93 TESTING, ADJUSTING, AND BA
Page 226 and 227:
G. Examine HVAC system and equipmen
Page 228 and 229:
a. Measure outlet static pressure a
Page 230 and 231:
3.10 TEMPERATURE-CONTROL VERIFICATI
Page 232 and 233:
B. Seasonal Periods: If initial TAB
Page 234 and 235:
1.07 SCHEDULING A. Schedule insulat
Page 236 and 237:
K. Insulation Terminations: For ins
Page 238 and 239:
1. Material: Mineral-fiber blanket.
Page 240 and 241:
2.00 PRODUCTS 2.01 MANUFACTURERS A.
Page 242 and 243:
M. Insulation Terminations: For ins
Page 244 and 245:
3.09 INTERIOR INSULATION APPLICATIO
Page 246 and 247:
B. Galvanized Sheet Steel: Lock-for
Page 248 and 249:
D. Install couplings tight to duct
Page 250 and 251:
E. Mechanical Cleaning Methodology:
Page 252 and 253:
2. Roll-Formed Steel Blades: 0.064-
Page 254 and 255:
23 34 23 POWER VENTILATORS 1.00 GEN
Page 256 and 257:
3. Propeller Fans: a. Aerovent; a T
Page 258 and 259:
2.05 MOTORS A. Refer to Division 23
Page 260 and 261:
23 37 13 DIFFUSERS, REGISTERS, AND
Page 262 and 263:
23 81 26 SPLIT-SYSTEM AIR-CONDITION
Page 264 and 265:
will occur as a result of overflow
Page 266 and 267:
B. Verify that units are installed
Page 268 and 269:
2.05 FAN terminal box. Fin surface
Page 270 and 271:
26 05 00 COMMON WORK RESULTS FOR EL
Page 272 and 273:
1.05 DELIVERY AND STORAGE A. Follow
Page 274 and 275:
D. All construction areas shall be
Page 276 and 277:
B. SINGLE CONDUCTORS: Conductor wit
Page 278 and 279:
26 05 19.01 WIRE CONNECTIONS AND DE
Page 280 and 281:
26 05 26 GROUNDING & BONDING FOR EL
Page 282 and 283:
G. Metal conduits stubbed up into s
Page 284 and 285:
26 05 29 HANGERS AND SUPPORTS FOR E
Page 286 and 287:
B. Maximum Support Spacing and Mini
Page 288 and 289:
26 05 33.01 CONDUITS 1.00 GENERAL 1
Page 290 and 291:
O. THREADED NIPPLES: As manufacture
Page 292 and 293:
2. Grade underground and outdoor co
Page 294 and 295:
26 05 33.02 WIREWAYS 1.00 GENERAL 1
Page 296 and 297:
C. Unless otherwise noted, location
Page 298 and 299:
C. PULL AND JUNCTION BOXES: Metal c
Page 300 and 301:
2. Provide conductor tags for condu
Page 302 and 303:
1. Color-Coding for Phase Identific
Page 304 and 305:
NO TEXT FOR THIS PAGE Identificatio
Page 306 and 307:
5. A relay coordination study shall
Page 308 and 309:
2.00 EXECUTION 2.01 GENERAL A. Prov
Page 310 and 311:
B. The CONTRACTOR shall adjust all
Page 312 and 313:
26 09 23 LIGHTING CONTROL DEVICES 1
Page 314 and 315:
F. A dedicated photocell input shal
Page 316 and 317:
26 24 16 LIGHTING AND BRANCH PANELB
Page 318 and 319:
D. Each circuit breaker used in 208
Page 320 and 321:
26 27 26 WIRING DEVICES 1.00 GENERA
Page 322 and 323:
A. Comply with NECA 1, including th
Page 324 and 325:
26 28 16 ENCLOSED SWITCHES AND CIRC
Page 326 and 327:
26 29 13 ENCLOSED CONTROLLERS 1.00
Page 328 and 329:
D. CONTROL POWER: Control power sha
Page 330 and 331:
H. Wiring in the combination starte
Page 332 and 333:
B. IEC or dual rated NEMA/IEC equip
Page 334 and 335:
5. Test each motor for proper phase
Page 336 and 337:
2.00 PRODUCTS 2.01 MATERIALS A. Mat
Page 338 and 339:
3.02 FIELD QUALITY CONTROL A. The l
Page 340 and 341:
D. LAMPS 1. FLUORESCENT: Cool white
Page 342 and 343:
31 23 10 STRUCTURAL EXCAVATION AND
Page 344 and 345:
3.00 EXECUTION 3.01 PREPARATION Cle
Page 346:
3. Areas of the fill being compacte
show all

final bid specs 09328.pdf - Freese and Nichols, Inc.

Create successful ePaper yourself

Delete template?

Save as template?