R&S WinIQSIM2 Software Manual - Rohde & Schwarz

More documents

Recommendations

Info

R&S ® WinIQSIM2 Remote Control Commands R&S Signal Generator Waveform and List Format *WAI WAIt to continue Prevents servicing of the subsequent commands until all preceding commands have been executed and all signals have settled (see also command synchronization and *OPC). Usage: Event 7.2 R&S Signal Generator Waveform and List Format The R&S WinIQSIM2 uses a tag-oriented format for externally or internally generated waveforms as well as for data and control lists. The data can be transmitted via the GPIB interface from an external computer to the instrument and vice versa. A waveform version number is not necessary due to the flexible, tag-based form. Tags are self-contained information units. Their general format is {Name: Data} or {Name-Length: Data}. The colon separates the name part and the data part. The colon can be followed by a space for the sake of legibility. The Name identifies the tag. It is always expressed in capital letters. The Data is tag-specific, and in most cases it is in ASCII plain text. The Length specifies the number of bytes in a WAVEFORM tag or DATA LIST tag (from : to }, ASCII integer). Each waveform file must begin with the TYPE tag. The sequence of the remaining tags is arbitrary. For each tag an indication shows whether it must be included in the file concerned (mandatory) or may be included (optional). Unknown tags are not analyzed by the R&S WinIQSIM2. On the other hand they are left unchanged, are saved without an error message and can be read back again. R&S AMIQ waveforms can also be loaded on the instrument, where they are converted internally into an R&S WinIQSIM2 waveform. 7.2.1 Tag Description This section first describe the mandatory TYPE tag which identifies the file and is always located at the start of the file. The rest of the tags used in the R&S WinIQSIM2 are then described in alphabetical order. Most tags are valid for all three file types. If a tag is valid only for a single file type, e.g. only for a waveform, this fact is indicated in the description. {TYPE: magic, xxxxxxxx}................................................................................................169 {CLOCK: frequency}.......................................................................................................170 {COMMENT: string} .......................................................................................................170 Software Manual 1008.0858.42 ─ 10 168
R&S ® WinIQSIM2 Remote Control Commands R&S Signal Generator Waveform and List Format {COPYRIGHT: string}.....................................................................................................171 {DATA BITLENGTH: BitLength}.......................................................................................171 {DATA LIST-Length: #d0d1...dx...dN-1…}.........................................................................171 {DATE: yyyy-mm-dd;hh:mm:ss}.......................................................................................172 {EMPTYTAG-Length: #EmptySequence}..........................................................................172 {CONTROL LENGTH: ControlLength}..............................................................................173 {LEVEL OFFS: RMSOffset_dB,PeakOffset_dB}................................................................173 {SAMPLES: Samples}....................................................................................................174 {[TRACE] LIST [#]: Pos0:Val0;Pos1:Val1;...Posx:Valx;...PosN-1:ValN-1}..............................174 {WAVEFORM-Length: #I0Q0I1Q1...IxQx...IN-1QN-1…}.....................................................175 {MWV_SEGMENT_COUNT: NumOfSeg}.........................................................................177 {MWV_SEGMENT_LENGTH: SamplesSeg0, SamplesSeg1, …, SamplesSegN-1}...............177 {MWV_SEGMENT_START: SampleStartOffsetSeg0, SampleStartOffsetSeg1, …, SampleStartOffsetSegN-1}.......177 {MWV_SEGMENT_CLOCK_MODE: Mode}......................................................................177 {MWV_SEGMENT_CLOCK: ClockSeg0, ClockSeg1, …, ClockSegN-1}...............................178 {MWV_SEGMENT_LEVEL_OFFS: RMSOffset_dBSeg0, PeakOffset_dBSeg0, …,RMSOffset_dBSegN-1, PeakOffset_dBSegN-1} ..........................................................................................................................179 {MWV_SEGMENT_FILES: “FileNameSeg0.wv”, “FileNameSeg1.wv”, …, “FileNameSegN-1.wv”}........................179 {MWV_SEGMENTx_COMMENT: text}.............................................................................179 {CONTROL LIST WIDTH4–Length: #m0m1…mx…mM-1}..................................................180 {TYPE: magic, xxxxxxxx} (mandatory, must be the first tag in the file) Identifies the file as a valid R&S WinIQSIM2 file. It must be present and must be the first in the waveform. If a file of the same name already exists on the target medium, it is overwritten. Setting parameters: magic Designates the file type and has the following values: SMU-WV A valid R&S WinIQSIM2 waveform. SMU-MWV A valid R&S WinIQSIM2 multi segment waveform. SMU-DL A valid R&S WinIQSIM2 data list. SMU-CL A valid R&S WinIQSIM2 control list. Software Manual 1008.0858.42 ─ 10 169
Page 1 and 2:
R&S ® WinIQSIM2 Signal Generation
Page 3 and 4:
Basic Safety Instructions Always re
Page 5 and 6:
Basic Safety Instructions Operating
Page 7 and 8:
Basic Safety Instructions 2. Before
Page 9 and 10:
Instrucciones de seguridad elementa
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Quality management and environmenta
Page 19 and 20:
R&S ® WinIQSIM2 Contents Contents
Page 21 and 22:
R&S ® WinIQSIM2 Contents Data Sour
Page 23 and 24:
R&S ® WinIQSIM2 Contents 6.1.4.1 P
Page 25 and 26:
R&S ® WinIQSIM2 Preface Documentat
Page 27 and 28:
R&S ® WinIQSIM2 Signal Generation
Page 29 and 30:
R&S ® WinIQSIM2 Installation of R&
Page 31 and 32:
R&S ® WinIQSIM2 Getting Started Sy
Page 33 and 34:
R&S ® WinIQSIM2 Getting Started Si
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
R&S ® WinIQSIM2 Graphical User Int
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134: R&S ® WinIQSIM2 Graphical User Int
Page 145 and 146: R&S ® WinIQSIM2 Automation of R&S
Page 181 and 182: R&S ® WinIQSIM2 Remote Control Com
Page 183: R&S ® WinIQSIM2 Remote Control Com
Page 235 and 236:
R&S ® WinIQSIM2 Remote Control Com
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
Page 303 and 304:
Page 305 and 306:
Page 307 and 308:
Page 309 and 310:
Page 311 and 312:
Page 313 and 314:
R&S ® WinIQSIM2 Error Messages Err
Page 315 and 316:
R&S ® WinIQSIM2 Error Messages Dev
Page 317 and 318:
R&S ® WinIQSIM2 List of Commands :
Page 319 and 320:
R&S ® WinIQSIM2 List of Commands [
Page 321 and 322:
R&S ® WinIQSIM2 List of Commands [
Page 323 and 324:
R&S ® WinIQSIM2 Index Index 140 -
Page 325 and 326:
R&S ® WinIQSIM2 Index Graphics ...
Page 327 and 328:
R&S ® WinIQSIM2 Index Sequential c
show all

R&S WinIQSIM2 Software Manual - Rohde & Schwarz

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?