R&S WinIQSIM2 Software Manual - Rohde & Schwarz

More documents

Recommendations

Info

R&S ® WinIQSIM2 Graphical User Interface Baseband Block General Settings The upper part of the menu is used for powering up digital modulation as well as for calling the default settings and user-defined standards. State - Digital Modulation Enables/disables digital modulation. Switching on digital modulation turns off all the other digital standards. Remote command: [:SOURce]:BB:DM:STATe on page 236 Set To Default - Digital Modulation Calls default settings. The values are shown in the following table. Parameter State Value Not affected by Set to Default Data Source PRBS 9 Standard Symbol Rate Coding Modulation Type Filter GSM 270.833 ksymb/s GSM MSK Gauss (FSK) Filter Parameter BxT 0.3 Power Ramp Control Attenuation Ramp Time Ramp Function 15 dB 1 sym Cosine Fall Delay 0 Rise Delay 0 Source State Marker Internal Off Marker Mode On/Off Ratio Clock Source Mode Internal Symbol Remote command: [:SOURce]:BB:DM:PRESet on page 234 Save/Recall - Digital Modulation Calls the "Save/Recall" dialog. Software Manual 1008.0858.42 ─ 10 64
R&S ® WinIQSIM2 Graphical User Interface Baseband Block From the "Save/Recall" dialog the "File Select" windows for saving and recalling the complete settings in the "Custom Digital Modulation" menu can be called. The Digital Modulation Settings are stored as files with the predefined file extension *.dm. The file name and the directory they are stored in are user-definable. The complete settings in the "Custom Digital Modulation" dialog are saved and recalled. Remote command: [:SOURce]:BB:DM:SETTing:CATalog? on page 259 [:SOURce]:BB:DM:SETTing:DELete on page 260 [:SOURce]:BB:DM:SETTing:LOAD on page 260 [:SOURce]:BB:DM:SETTing:STORe on page 260 Generate Waveform File - Digital Modulation Opens the submenu for storing the current signal as ARB signal in a waveform file. The file name is entered in the submenu. The file is stored with the predefined file extension *.wv. The file name and the directory it is stored in are user-definable. Remote command: [:SOURce]:BB:DM:WAVeform:CREate on page 237 Sequence Length - Digital Modulation Sets the sequence length of the signal in symbols. The signal is calculated in advance, saved as waveform file, and output in the selected arbitrary waveform generator. Note: "Sequence Length" * "Oversampling" must not exceed the maximum number of samples in the arbitrary waveform generator. Remote command: [:SOURce]:BB:DM:SLENgth on page 236 Fast Save Determines whether the instrument performs an absolute or a differential storing of the settings. Enable this function to accelerate the saving process by saving only the settings with values different to the default ones. Software Manual 1008.0858.42 ─ 10 65
Page 1 and 2:
R&S ® WinIQSIM2 Signal Generation
Page 3 and 4:
Basic Safety Instructions Always re
Page 5 and 6:
Basic Safety Instructions Operating
Page 7 and 8:
Basic Safety Instructions 2. Before
Page 9 and 10:
Instrucciones de seguridad elementa
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Quality management and environmenta
Page 19 and 20:
R&S ® WinIQSIM2 Contents Contents
Page 21 and 22:
R&S ® WinIQSIM2 Contents Data Sour
Page 23 and 24:
R&S ® WinIQSIM2 Contents 6.1.4.1 P
Page 25 and 26:
R&S ® WinIQSIM2 Preface Documentat
Page 27 and 28:
R&S ® WinIQSIM2 Signal Generation
Page 29 and 30: R&S ® WinIQSIM2 Installation of R&
Page 31 and 32: R&S ® WinIQSIM2 Getting Started Sy
Page 33 and 34: R&S ® WinIQSIM2 Getting Started Si
Page 43 and 44: R&S ® WinIQSIM2 Graphical User Int
Page 79: R&S ® WinIQSIM2 Graphical User Int
Page 131 and 132:
R&S ® WinIQSIM2 Graphical User Int
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
R&S ® WinIQSIM2 Automation of R&S
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
R&S ® WinIQSIM2 Remote Control Com
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
Page 303 and 304:
Page 305 and 306:
Page 307 and 308:
Page 309 and 310:
Page 311 and 312:
Page 313 and 314:
R&S ® WinIQSIM2 Error Messages Err
Page 315 and 316:
R&S ® WinIQSIM2 Error Messages Dev
Page 317 and 318:
R&S ® WinIQSIM2 List of Commands :
Page 319 and 320:
R&S ® WinIQSIM2 List of Commands [
Page 321 and 322:
R&S ® WinIQSIM2 List of Commands [
Page 323 and 324:
R&S ® WinIQSIM2 Index Index 140 -
Page 325 and 326:
R&S ® WinIQSIM2 Index Graphics ...
Page 327 and 328:
R&S ® WinIQSIM2 Index Sequential c
show all

R&S WinIQSIM2 Software Manual - Rohde & Schwarz

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?