R&S WinIQSIM2 Software Manual - Rohde & Schwarz

More documents

Recommendations

Info

R&S ® WinIQSIM2 Remote Control Commands SOURce:BB:ARB:WSEG Subsystem [:SOURce]:BB:ARBitrary:MCARrier:STATe The command enables/disables multi carrier generation. Parameters: Example: 0 | 1 | OFF | ON *RST: OFF BB:ARB:MCAR:STAT ON enables multi carrier generation. Manual operation: See "State Multi Carrier" on page 93 [:SOURce]:BB:ARBitrary:MCARrier:TIME:MODE The command selects the mode for calculating the resulting signal period of the multi carrier waveform. The resulting period is always calculated for all carriers in the carrier table irrespective of their state (ON/OFF). Parameters: Example: USER | LONG | SHORt LONG The resulting signal period is defined by the longest I/Q file in the carrier table. Shorter I/Q files are periodically repeated. SHORt The resulting signal period is defined by the shortest I/Q file in the carrier table. Only the first part of longer I/Q files is used. USER The signal period can be set with command SOUR:BB:ARB:MCARr:TIME. Shorter I/Q files are repeated periodically, and only the first part of longer I/Q files is used. *RST: LONG BB:ARB:MCAR:TIME:MODE LONG selects signal period mode long Manual operation: See "Signal Period Mode" on page 96 7.7 SOURce:BB:ARB:WSEG Subsystem The WSEGment subsystem contains the commands for setting the Multi Segment Waveform Generator. [:SOURce]:BB:ARBitrary:WSEGment:CONFigure:BLANk:APPend..............................225 [:SOURce]:BB:ARBitrary:WSEGment:CONFigure:CATalog?......................................225 [:SOURce]:BB:ARBitrary:WSEGment:CONFigure:CLOCk..........................................226 [:SOURce]:BB:ARBitrary:WSEGment:CONFigure:CLOCk:MODE...............................226 [:SOURce]:BB:ARBitrary:WSEGment:CONFigure:COMMent......................................227 [:SOURce]:BB:ARBitrary:WSEGment:CONFigure:DELete..........................................227 [:SOURce]:BB:ARBitrary:WSEGment:CONFigure:LEVel[:MODE]................................227 Software Manual 1008.0858.42 ─ 10 224
R&S ® WinIQSIM2 Remote Control Commands SOURce:BB:ARB:WSEG Subsystem [:SOURce]:BB:ARBitrary:WSEGment:CONFigure:MARKer:ESEGment.......................228 [:SOURce]:BB:ARBitrary:WSEGment:CONFigure:MARKer:FSEGment........................228 [:SOURce]:BB:ARBitrary:WSEGment:CONFigure:MARKer:MODE..............................229 [:SOURce]:BB:ARBitrary:WSEGment:CONFigure:OFILe............................................229 [:SOURce]:BB:ARBitrary:WSEGment:CONFigure:SEGMent:APPend..........................229 [:SOURce]:BB:ARBitrary:WSEGment:CONFigure:SEGMent:CATalog?.......................230 [:SOURce]:BB:ARBitrary:WSEGment:CONFigure:SELect..........................................230 [:SOURce]:BB:ARBitrary:WSEGment:CREate...........................................................231 [:SOURce]:BB:ARBitrary:WSEGment:NEXT.............................................................231 [:SOURce]:BB:ARBitrary:WSEGment:NEXT:EXECute...............................................232 [:SOURce]:BB:ARBitrary:WSEGment:SEQuence:APPend..........................................232 [:SOURce]:BB:ARBitrary:WSEGment:SEQuence:SELect...........................................233 [:SOURce]:BB:ARBitrary:WSEGment:STATe............................................................233 [:SOURce]:BB:ARBitrary:WSEGment:CONFigure:BLANk:APPend , Adds a blank segment to the multi segment file. Setting parameters: Example: Usage: float Specifies the number of samples. Range: 512 to 1E7 Increment: 1 *RST: 1000 float Determines the clock rate. Range: 400 Hz to Max (depends on instrument type) Increment: 0.001 *RST: 1E8 SOUR:BB:ARB:WSEG:CONF:SEL "MSegFile" selects a multi segment file. SOUR:BB:ARB:WSEG:CONF:BLAN:APP 1000,100000000 adds a blank segment with 1000 samples and 100 MHz clock rate to the selected multi segment file Setting only Manual operation: See "Clock Rate" on page 108 [:SOURce]:BB:ARBitrary:WSEGment:CONFigure:CATalog? This command queries the available configuration files in the specified default directory. The configuration files are used to create multi segment waveform files. Return values: string Software Manual 1008.0858.42 ─ 10 225
Page 1 and 2:
R&S ® WinIQSIM2 Signal Generation
Page 3 and 4:
Basic Safety Instructions Always re
Page 5 and 6:
Basic Safety Instructions Operating
Page 7 and 8:
Basic Safety Instructions 2. Before
Page 9 and 10:
Instrucciones de seguridad elementa
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Quality management and environmenta
Page 19 and 20:
R&S ® WinIQSIM2 Contents Contents
Page 21 and 22:
R&S ® WinIQSIM2 Contents Data Sour
Page 23 and 24:
R&S ® WinIQSIM2 Contents 6.1.4.1 P
Page 25 and 26:
R&S ® WinIQSIM2 Preface Documentat
Page 27 and 28:
R&S ® WinIQSIM2 Signal Generation
Page 29 and 30:
R&S ® WinIQSIM2 Installation of R&
Page 31 and 32:
R&S ® WinIQSIM2 Getting Started Sy
Page 33 and 34:
R&S ® WinIQSIM2 Getting Started Si
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
R&S ® WinIQSIM2 Graphical User Int
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
R&S ® WinIQSIM2 Automation of R&S
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
R&S ® WinIQSIM2 Remote Control Com
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190: R&S ® WinIQSIM2 Remote Control Com
Page 239: R&S ® WinIQSIM2 Remote Control Com
Page 291 and 292:
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
Page 303 and 304:
Page 305 and 306:
Page 307 and 308:
Page 309 and 310:
Page 311 and 312:
Page 313 and 314:
R&S ® WinIQSIM2 Error Messages Err
Page 315 and 316:
R&S ® WinIQSIM2 Error Messages Dev
Page 317 and 318:
R&S ® WinIQSIM2 List of Commands :
Page 319 and 320:
R&S ® WinIQSIM2 List of Commands [
Page 321 and 322:
R&S ® WinIQSIM2 List of Commands [
Page 323 and 324:
R&S ® WinIQSIM2 Index Index 140 -
Page 325 and 326:
R&S ® WinIQSIM2 Index Graphics ...
Page 327 and 328:
R&S ® WinIQSIM2 Index Sequential c
show all

R&S WinIQSIM2 Software Manual - Rohde & Schwarz

Create successful ePaper yourself

Delete template?

Save as template?