R&S WinIQSIM2 Software Manual - Rohde & Schwarz

More documents

Recommendations

Info

R&S ® WinIQSIM2 Remote Control Commands SOURce:AWGN Subsystem Example: Usage: AWGN:FREQ:RES? queries the actual frequency of the interfering sine Query only Manual operation: See "Resulting CW Frequency - AWGN" on page 124 [:SOURce]:AWGN:FREQuency:TARGet Sets the desired frequency of the sine in AWGN:MODE CW mode. The range of this parameter is limited to ± (Symbol Rate + Sample Rate)/4 Parameters: Example: float Range: -40E6 to 40E6 Increment: 0.01 *RST: 0 AWGN:FREQ:TARG 2kHz sets a frequency of 2 kHz for the interfering sine. Manual operation: See "Target CW Frequency - AWGN" on page 124 [:SOURce]:AWGN:MODE Selects the mode for generating the interfering signal. Parameters: Example: ONLY | ADD | CW ADD The AWGN noise signal is added to the baseband signal. ONLY The pure AWGN noise signal is modulated to the carrier. The connection to the baseband is interrupted. CW The sine interfering signal is added to the baseband signal. *RST: ADD SOURce:AWGN:MODE ONLY SOURce:AWGN:STATe ON selects the generation of a pure noise and activates it Manual operation: See "Mode - AWGN" on page 122 [:SOURce]:AWGN:POWer:CARRier available for Additive Noise and CW Interferer (SOUR:AWGN:MODE ADD|CW) modes Software Manual 1008.0858.42 ─ 10 206
R&S ® WinIQSIM2 Remote Control Commands SOURce:AWGN Subsystem Parameters: Example: float *RST: 0 Default unit: dBm AWGN:POW:CARR? queries the carrier power Manual operation: See "Carrier Power" on page 126 [:SOURce]:AWGN:POWer:MODE In Additive Noise (SOUR:AWGN:MODE ADD) mode, selects the mode for setting the noise power. Parameters: Example: CN | SN | EN CN|SN The noise power is set on the basis of the value entered for the carrier/noise or signal/noise ratio (SOURce:AWGN:CNRatio|SNRatio). EN The noise power is set on the basis of the value entered for the ratio of bit energy to noise power density (AWGN:ENR). *RST: CN|SN SOUR:AWGN:POW:MODE CN the noise power is set on the basis of the value entered for the carrier/noise ratio (AWGN:CNR). Manual operation: See "Set Power via - AWGN " on page 124 [:SOURce]:AWGN:POWer:NOISe Sets or queries the noise power in the system bandwidth depending on the selected mode: ● ● SOUR:AWGN:MODE ADD|CW Queries the noise/interferer power which is derived from the entered S/N value. "Noise Only" mode The command sets the noise power. Parameters: Example: float Default unit: dBm SOURce:AWGN:POWer:NOISe? queries the noise power in the system bandwidth. Response: 10 the noise power in the system bandwidth is 10 dBm. Software Manual 1008.0858.42 ─ 10 207
Page 1 and 2:
R&S ® WinIQSIM2 Signal Generation
Page 3 and 4:
Basic Safety Instructions Always re
Page 5 and 6:
Basic Safety Instructions Operating
Page 7 and 8:
Basic Safety Instructions 2. Before
Page 9 and 10:
Instrucciones de seguridad elementa
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Quality management and environmenta
Page 19 and 20:
R&S ® WinIQSIM2 Contents Contents
Page 21 and 22:
R&S ® WinIQSIM2 Contents Data Sour
Page 23 and 24:
R&S ® WinIQSIM2 Contents 6.1.4.1 P
Page 25 and 26:
R&S ® WinIQSIM2 Preface Documentat
Page 27 and 28:
R&S ® WinIQSIM2 Signal Generation
Page 29 and 30:
R&S ® WinIQSIM2 Installation of R&
Page 31 and 32:
R&S ® WinIQSIM2 Getting Started Sy
Page 33 and 34:
R&S ® WinIQSIM2 Getting Started Si
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
R&S ® WinIQSIM2 Graphical User Int
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
R&S ® WinIQSIM2 Automation of R&S
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172: R&S ® WinIQSIM2 Automation of R&S
Page 181 and 182: R&S ® WinIQSIM2 Remote Control Com
Page 221: R&S ® WinIQSIM2 Remote Control Com
Page 273 and 274:
R&S ® WinIQSIM2 Remote Control Com
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
Page 303 and 304:
Page 305 and 306:
Page 307 and 308:
Page 309 and 310:
Page 311 and 312:
Page 313 and 314:
R&S ® WinIQSIM2 Error Messages Err
Page 315 and 316:
R&S ® WinIQSIM2 Error Messages Dev
Page 317 and 318:
R&S ® WinIQSIM2 List of Commands :
Page 319 and 320:
R&S ® WinIQSIM2 List of Commands [
Page 321 and 322:
R&S ® WinIQSIM2 List of Commands [
Page 323 and 324:
R&S ® WinIQSIM2 Index Index 140 -
Page 325 and 326:
R&S ® WinIQSIM2 Index Graphics ...
Page 327 and 328:
R&S ® WinIQSIM2 Index Sequential c
show all

R&S WinIQSIM2 Software Manual - Rohde & Schwarz

Create successful ePaper yourself

Delete template?

Save as template?