R&S WinIQSIM2 Software Manual - Rohde & Schwarz

More documents

Recommendations

Info

R&S ® WinIQSIM2 Remote Control Commands MMEMory Subsystem ● The [state: start time] pairs in turn are separated by semicolons ";". ● The list state can be either 0 or 1. ● The time unit is the simple period. Example: "CW MODE LIST 0:0;380:1" for a CW trace: The list status starts at time 0 with 0, and at time point 380 symbol periods after start, it changes to 1. With the commands BB:DM:CLISt:... you can also generate control lists in binary fomat, if required. See chapter 7.8.2, "DM Lists", on page 249. 7.3 MMEMory Subsystem The MMEMory subsystem (Mass Memory) contains the commands for managing files and directories as well as for loading and storing complete instrument settings in files. The various drives can be selected using the "mass storage unit specifier " . The internal hard disk is selected with D:\, and a memory stick which is inserted at the USB interface is selected with E:\. The resources of a network can also be selected with in the syntax of the respective network, e.g. using the UNC format (Universal Naming Convention): \\server\share. The default drive is determined using the command MMEMory:MSIS . The C: drive is a protected system drive. This drive should not be accessed. Reconstruction of the system partition will not be possible without loss of data. Use the command :SYSTem:MMEMory:PATH:USER? to query the path of the directory for user-defined data. 7.3.1 File Naming Conventions To enable files in different file systems to be used, the following file naming conventions should be observed. The file name can be of any length and no distinction is made between uppercase and lowercase letters. The file and the optional file extension are separated by a dot. All letters and numbers are permitted (numbers are, however, not permitted at the beginning of the file name). If possible, special characters should not be used. The use of the slashes "\" and "/" should be avoided since they are used in file paths. A number of names are reserved for the Software Manual 1008.0858.42 ─ 10 186
R&S ® WinIQSIM2 Remote Control Commands MMEMory Subsystem operating system, e.g. CLOCK$, CON, AUX, COM1...COM4, LPT1...LPT3, NUL and PRN. In the R&S Signal Generator all files in which lists and settings are stored are given a characteristic extension. The extension is separated from the actual file name by a dot (see chapter 7.3.2, "Extensions for User Files", on page 187 for an overview of the file types). The two characters "*" and "?" function as "wildcards", meaning they are used for selecting several files. The "?" character represents exactly one character, while the "*" character represents all characters up to the end of the file name. "*.*" therefore stands for all files in a directory. When used in conjunction with the commands, the parameter is specified as a string parameter with quotation marks. It can contain either the complete path including the drive, only the path and the file name, or only the file name. The file name must include the file extension. The same applies for the parameters and . Depending on how much information is provided, either the values specified in the parameter or the values specified with the commands MMEM:MSIS (default drive) and MMEM:CDIR (default directory) are used for the path and the drive settings in the commands. Before the instrument settings can be stored in a file, they have to be stored in an intermediate memory using common command *SAV . The specified number is subsequently used in the :MMEMory:STORe:STATe command. Also, subsequently to loading a file with instrument settings with command :MMEMory:LOAD:STATe, these settings have to be activated with the common command *RCL . 7.3.2 Extensions for User Files The following table lists all available file extensions for user files. Table 7-1: List of the automatically assigned file extensions in the instrument Function/Digital Standard List type Contents File suffix Instrument State Settings Instrument settings *.savrcl Import Settings Settings Settings *.import "Arbitrary Waveform Generator" Waveform ARB waveforms ARB multi segment waveforms *.wv Waveform ARB multi carrier settings *.arb_multcarr Configuration data Configuration file for creation of multisegment ARB waveforms *.inf_mswv Play List ARB Sequencing List *.wvs "DM" Data List Digital modulation data *.dm_iqd *.tdm Software Manual 1008.0858.42 ─ 10 187
Page 1 and 2:
R&S ® WinIQSIM2 Signal Generation
Page 3 and 4:
Basic Safety Instructions Always re
Page 5 and 6:
Basic Safety Instructions Operating
Page 7 and 8:
Basic Safety Instructions 2. Before
Page 9 and 10:
Instrucciones de seguridad elementa
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Quality management and environmenta
Page 19 and 20:
R&S ® WinIQSIM2 Contents Contents
Page 21 and 22:
R&S ® WinIQSIM2 Contents Data Sour
Page 23 and 24:
R&S ® WinIQSIM2 Contents 6.1.4.1 P
Page 25 and 26:
R&S ® WinIQSIM2 Preface Documentat
Page 27 and 28:
R&S ® WinIQSIM2 Signal Generation
Page 29 and 30:
R&S ® WinIQSIM2 Installation of R&
Page 31 and 32:
R&S ® WinIQSIM2 Getting Started Sy
Page 33 and 34:
R&S ® WinIQSIM2 Getting Started Si
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
R&S ® WinIQSIM2 Graphical User Int
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
R&S ® WinIQSIM2 Automation of R&S
Page 147 and 148:
Page 149 and 150:
Page 151 and 152: R&S ® WinIQSIM2 Automation of R&S
Page 181 and 182: R&S ® WinIQSIM2 Remote Control Com
Page 201: R&S ® WinIQSIM2 Remote Control Com
Page 253 and 254:
R&S ® WinIQSIM2 Remote Control Com
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
Page 303 and 304:
Page 305 and 306:
Page 307 and 308:
Page 309 and 310:
Page 311 and 312:
Page 313 and 314:
R&S ® WinIQSIM2 Error Messages Err
Page 315 and 316:
R&S ® WinIQSIM2 Error Messages Dev
Page 317 and 318:
R&S ® WinIQSIM2 List of Commands :
Page 319 and 320:
R&S ® WinIQSIM2 List of Commands [
Page 321 and 322:
R&S ® WinIQSIM2 List of Commands [
Page 323 and 324:
R&S ® WinIQSIM2 Index Index 140 -
Page 325 and 326:
R&S ® WinIQSIM2 Index Graphics ...
Page 327 and 328:
R&S ® WinIQSIM2 Index Sequential c
show all

R&S WinIQSIM2 Software Manual - Rohde & Schwarz

Create successful ePaper yourself

Delete template?

Save as template?