Toshiba PROSEC T1-16S PLC User's Manual - CTi Automation

More documents

Recommendations

Info

7. Instructions FUN 043 +1 Increment Expression Input −[ +1 A ]− Output Function When the input is ON, the data of A is increased by 1 and stored in A. Execution condition Input Operation Output OFF No execution OFF ON Execution ON 154 T1-16S User’s Manual 6F3B0253 Operand Name Device Register Constant Index X Y R S T. C. XWYWRWSW T C D I J K A Operation data √ √ √ √ √ √ √ √ √ √ Example At the rising edge of X004 changes from OFF to ON, the data of D0050 is increased by 1 and stored in D0050. If the data of D0050 is 750 before the execution, it will be 751 after the execution. D0050 D0050 750 + 1 751 Note • There is no limit value for this instruction. When the data of operand A is 32767 before the execution, it will be -32768 after the execution. CTi Automation - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.ctiautomation.net - Email: info@ctiautomation.net
FUN 045 -1 Decrement Expression Input −[ -1 A ]− Output Function When the input is ON, the data of A is decreased by 1 and stored in A. Execution condition Input Operation Output OFF No execution OFF ON Execution ON 6F3B0253 7. Instructions Operand Name Device Register Constant Index X Y R S T. C. XWYWRWSW T C D I J K A Operation data √ √ √ √ √ √ √ √ √ √ Example At the rising edge of X005 changes from OFF to ON, the data of D0050 is decreased by 1 and stored in D0050. If the data of D0050 is 1022 before the execution, it will be 1021 after the execution. D0050 D0050 1022 - 1 1021 Note • There is no limit value for this instruction. When the data of operand A is -32768 before the execution, it will be 32767 after the execution. Basic Hardware and Function 155 CTi Automation - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.ctiautomation.net - Email: info@ctiautomation.net
Page 1 and 2:
6F3B0253 UM-TS01∗∗∗-E031 PROG
Page 3 and 4:
CE Marking 6F3B0253 The Programmabl
Page 5 and 6:
Safety Precautions This manual is p
Page 7 and 8:
Operation: Safety Precautions ! WAR
Page 9 and 10:
Safety Label The safety label as sh
Page 11 and 12:
Terminology The following is a list
Page 13 and 14:
6F3B0253 Contents 5. Operating Syst
Page 15 and 16:
Section 1 System Configuration 1.1
Page 17 and 18:
6F3B0253 1. System Configuration Me
Page 19 and 20:
6F3B0253 1. System Configuration Pu
Page 21 and 22:
1.3 System configuration The follow
Page 23 and 24:
1.5 Components 1.5.1 Basic unit The
Page 25 and 26:
I/O status LEDs: Indicates the ON/O
Page 27 and 28:
1.5.2 I/O modules NOTE 6F3B0253 1.
Page 29 and 30:
1.6 Programmer port function 6F3B02
Page 31 and 32:
6F3B0253 1. System Configuration Co
Page 33 and 34:
6F3B0253 1. System Configuration Fr
Page 35 and 36:
1.9 Peripheral tools The following
Page 37 and 38:
Program Storage Module (RM102) Mult
Page 39 and 40:
Section 2 Specifications 2.1 Genera
Page 41 and 42:
NOTE (3) The 5Vdc current consumpti
Page 43 and 44:
Functional specifications (cont’d
Page 45 and 46:
• Input signal connections L Serv
Page 47 and 48:
• Output signal connections L Ser
Page 49 and 50:
Section 3 I/O Application Precautio
Page 51 and 52:
6F3B0253 3. I/O Application Precaut
Page 53 and 54:
6F3B0253 3. I/O Application Precaut
Page 55 and 56:
Section 4 Installation and Wiring 4
Page 57 and 58:
4.2 Installing the unit ! CAUTION N
Page 59 and 60:
4.3 Wiring terminals ! CAUTION 6F3B
Page 61 and 62:
4.5 Power supply wiring ! CAUTION W
Page 63 and 64:
4.6 I/O wiring ! CAUTION 6F3B0253 4
Page 65 and 66:
Section 5 Operating System Overview
Page 67 and 68:
6F3B0253 5. Operating System Overvi
Page 69 and 70:
EEPROM User program (8 k steps) and
Page 71 and 72:
5.3 Scanning 6F3B0253 5. Operating
Page 73 and 74:
6F3B0253 5. Operating System Overvi
Page 75 and 76:
Section 6 Programming Information 6
Page 77 and 78:
Addressing devices 6F3B0253 6. Prog
Page 79 and 80:
6F3B0253 6. Programming Information
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
The followings are examples of inde
Page 91 and 92:
6.4 I/O allocation 6F3B0253 6. Prog
Page 93 and 94:
6.5 T1-16S memory mode setting 6F3B
Page 95 and 96:
System information 6F3B0253 6. Prog
Page 97 and 98:
6.6.2 Sub-program #1 6F3B0253 6. Pr
Page 99 and 100:
6.6.5 Subroutines 6F3B0253 6. Progr
Page 101 and 102:
6.8 Program execution sequence The
Page 103 and 104:
Page 105 and 106: 6.10 Password protection 6F3B0253 6
Page 107 and 108: Section 7 Instructions 7.1 List of
Page 109 and 110: Basic ladder instructions (continue
Page 111 and 112: Logical operations 6F3B0253 7. Inst
Page 113 and 114: Compare instructions (continued) 6F
Page 115 and 116: Functions 6F3B0253 7. Instructions
Page 117 and 118: Special I/O instructions 6F3B0253 7
Page 119 and 120: Expression A Input Output NO contac
Page 121 and 122: Expression Input Output Transitiona
Page 123 and 124: ( ) Coil Expression A Input ( ) Fun
Page 125 and 126: I Inverter Expression Input I Outpu
Page 127 and 128: P Positive pulse contact Expression
Page 129 and 130: ( P ) Positive pulse coil Expressio
Page 131 and 132: TON ON delay timer Expression Input
Page 133 and 134: SS Single shot timer Expression Inp
Page 135 and 136: MCS MCR Expression Input [ MCS ] Ma
Page 137 and 138: END End Expression [ END ] 6F3B0253
Page 139 and 140: FUN 019 DMOV Double-word data trans
Page 141 and 142: FUN 022 XCHG Data exchange Expressi
Page 143 and 144: FUN 025 TMOV Table transfer Express
Page 145 and 146: FUN 027 + Addition Expression Input
Page 147 and 148: FUN 029 ∗ Multiplication Expressi
Page 149 and 150: FUN 031 D+ Double-word addition Exp
Page 151 and 152: FUN 035 +C Addition with carry Expr
Page 153 and 154: FUN 039 U∗ Unsigned multiplicatio
Page 155: FUN 041 DIV Unsigned double/single
Page 159 and 160: FUN 050 OR OR Expression Input −[
Page 161 and 162: FUN 056 MAVE Moving average Express
Page 163 and 164: FUN 062 HTOA Hex to ASCII conversio
Page 165 and 166: FUN 064 TEST Bit test Expression In
Page 167 and 168: FUN 069 SHL1 1 bit shift left Expre
Page 169 and 170: FUN 071 SHL n bit shift left Expres
Page 171 and 172: 6F3B0253 7. Instructions The figure
Page 173 and 174: 6F3B0253 7. Instructions 9 devices
Page 175 and 176: FUN 079 RTL1 1 bit rotate left Expr
Page 177 and 178: FUN 081 RTL n bit rotate left Expre
Page 179 and 180: FUN 091 DPX Demultiplexer Expressio
Page 181 and 182: FUN 097 >= Greater than or equal Ex
Page 183 and 184: FUN 099 Not equal Expression Input
Page 185 and 186: FUN 101
Page 187 and 188: FUN 103 D>= Double-word greater tha
Page 189 and 190: FUN 105 D Double-word not equal Exp
Page 191 and 192: FUN 107 D Constant 0 R014 is OFF No
Page 193 and 194: FUN 109 U>= Unsigned greater than o
Page 195 and 196: FUN 111 U Unsigned not equal Expres
Page 197 and 198: FUN 113 U Constant 35000 R020 is OF
Page 199 and 200: FUN 115 RST Device/register reset E
Page 201 and 202: FUN 119 RSTC Reset carry Expression
Page 203 and 204: FUN 121 DEC Decode Expression Input
Page 205 and 206: FUN 128 CALL Subroutine call Expres
Page 207 and 208:
FUN 132 FOR FOR (FOR-NEXT loop) Exp
Page 209 and 210:
FUN 137 SUBR Subroutine entry Expre
Page 211 and 212:
FUN 141 DI Disable interrupt Expres
Page 213 and 214:
FUN 143 WDT Watchdog timer reset Ex
Page 215 and 216:
FUN 145 STIN Step sequence input Ex
Page 217 and 218:
FUN 147 F/F Flip-flop Expression Se
Page 219 and 220:
FUN 154 CLND Set calendar Expressio
Page 221 and 222:
FUN 156 PID3 Pre-derivative real PI
Page 223 and 224:
PID algorithm: ∆MVn= KP ⋅ ( ∆
Page 225 and 226:
6F3B0253 7. Instructions • Manual
Page 227 and 228:
FUN 161 LL Lower limit Expression I
Page 229 and 230:
FUN 163 MIN Minimum value Expressio
Page 231 and 232:
FUN 165 FG Function generator Expre
Page 233 and 234:
FUN 180 ABS Absolute value Expressi
Page 235 and 236:
FUN 183 DNEG Double-word 2’s comp
Page 237 and 238:
6F3B0253 7. Instructions Operand A
Page 239 and 240:
FUN 188 BIN Binary conversion Expre
Page 241 and 242:
FUN 235 I/O Direct I/O Expression I
Page 243 and 244:
FUN 236 XFER Expanded data transfer
Page 245 and 246:
CPU register ↔ T1S RS-485 port 6
Page 247 and 248:
6F3B0253 7. Instructions FUN 236 XF
Page 249 and 250:
Data exchange mode (Mode 0) > 6F3B0
Page 251 and 252:
Monitor mode (Mode 1) > 6F3B0253 7.
Page 253 and 254:
Read command mode (Mode 2) > 6F3B02
Page 255 and 256:
Broadcast mode (Mode 4) > 6F3B0253
Page 257 and 258:
Section 8 Special I/O Functions 8.1
Page 259 and 260:
Mode setting for the special I/O fu
Page 261 and 262:
6F3B0253 8. Special I/O Functions T
Page 263 and 264:
8.3 High speed counter 8.3.1 Single
Page 265 and 266:
8.3.2 Single phase speed-counter Fu
Page 267 and 268:
8.3.3 Quadrature bi-pulse counter F
Page 269 and 270:
Sample program (H0803) 6F3B0253 8.
Page 271 and 272:
Sample program Main program (H3045)
Page 273 and 274:
8.6 Pulse output function Function
Page 275 and 276:
8.7 PWM output function Function 6F
Page 277 and 278:
Section 9 Maintenance and Checks 9.
Page 279 and 280:
9.2 Daily checks ! CAUTION 6F3B0253
Page 281 and 282:
(Periodic checks - continued) 6F3B0
Page 283 and 284:
Section 10 Troubleshooting 10.1 Tro
Page 285 and 286:
10.1.1 Power supply check 6F3B0253
Page 287 and 288:
10.1.4 Input check 6F3B0253 10. Tro
Page 289 and 290:
10.1.6 Environmental problem 6F3B02
Page 291 and 292:
6F3B0253 10. Troubleshooting Error
Page 293 and 294:
6F3B0253 10. Troubleshooting Error
Page 295 and 296:
Appendix A.1 List of models and typ
Page 297 and 298:
Appendix A.2 Instruction index •
Page 299:
Appendix • Instruction symbol ∗
show all

Toshiba PROSEC T1-16S PLC User's Manual - CTi Automation

Create successful ePaper yourself

Delete template?

Save as template?