LTV 1200 Operator's Manual - CareFusion Emergency Preparedness

Recommendations

Info

Patient Assist Use the PNT ASSIST menu item to configure the Patient Assist port output signal to be generated for use with remote alarm systems. • Allows for the changing of the patient assist alarm output signal used with remote alarm systems, which in turn will allow users a means of distinguishing the high pressure alarm (HIGH PRES) from other alarms. To select the Patient Assist output signal: 1) Push the Select button while PNT ASSIST is displayed. 2) NORMAL or PULSE is displayed. • When NORMAL is selected, the ventilator sets the Patient Assist Port output signal continuously on for all alarms and is for use with single tone remote alarm and patient assist call systems. NORMAL is the factory set default setting. • When PULSE is selected, the ventilator sets the Patient Assist Port output signal continuous on for the HIGH PRES alarm, cycles the Patient Assist output signal on / off for all other alarms and is for use with dual tone remote alarm systems. 3) Turn the Set Value knob until the desired setting is displayed. 4) Push the Select button. Range: PULSE or NORMAL Exit To return to the top of the ALARM OP menu: 1) Push the Select button while EXIT is displayed. Page 10-6 LTV ® 1200 Ventilator Operator’s Manual p/n 18247-001, Rev. G
Vent Operations Use the Vent Operations menu to set up ventilator controls and options that are not available directly from front panel controls. The menu is set up as follows: VENT OP RISE TIME FLOW TERM TIME TERM PC FLOW TERM LEAK COMP O2 CONSERVE O2 FLUSH CTRL UNLOCK LANGUAGE VER xx.xx USAGE xxxxx.x COM SETTING SET DATE SET TIME DATE FORMAT PIP LED LTV xxxx / xxxxxx VHome xxx SET DEFAULTS (accessed through Vent Check menu) O2 CYL DUR EXIT Operator’s Manual LTV ® 1200 Ventilator Page 10-7 p/n 18247-001, Rev. G
Page 1:
LTV ® 1200 Ventilator / MR Conditi
Page 4 and 5:
Warranty Pulmonetic Systems warrant
Page 6 and 7:
Notice To Operators Unsafe Operatio
Page 8 and 9:
Chapter 6 - Controls...............
Page 10 and 11:
LPPS OFF...........................
Page 12 and 13:
Chapter 15 - Troubleshooting ......
Page 14 and 15:
Operator’s Safety Information All
Page 16 and 17:
WARNING Battery run time - When the
Page 18 and 19:
AVERTISSEMENT Personnel non qualifi
Page 20 and 21:
AVERTISSEMENT Concentration d’oxy
Page 22 and 23:
Cautions CAUTION Ventilator Sterili
Page 24 and 25:
CAUTION External Battery Pack - The
Page 26 and 27:
ATTENTION Nettoyage du panneau fron
Page 28 and 29:
Symbols Symbol Compliance 3 Title A
Page 30 and 31:
Indications for Use The LTV ® 1200
Page 32 and 33:
Information/Assistance For addition
Page 34 and 35:
Volume Control Breaths For Volume C
Page 36 and 37:
Pressure Control Breaths (cont) Pre
Page 38 and 39:
Spontaneous Breaths For Spontaneous
Page 40 and 41:
SIMV Mode SIMV mode is selected whe
Page 42 and 43:
NPPV Mode Non-invasive Positive Pre
Page 44 and 45:
Volume Pressure Ventilation The LTV
Page 46 and 47:
Setting a Control There are 5 kinds
Page 48 and 49:
Bright, Dim and Blank Control Displ
Page 50 and 51:
Control Locking The front panel con
Page 52 and 53:
Breath Rate Use the Breath Rate con
Page 54 and 55:
High Pressure Limit Use the High Pr
Page 56 and 57:
Inspiratory Hold An Inspiratory Hol
Page 58 and 59:
Expiratory Hold An Expiratory Hold
Page 60 and 61:
Inspiratory Time This control sets
Page 62 and 63:
Low Pressure The Low Pressure alarm
Page 64 and 65:
Low Pressure O 2 Source (cont.) NOT
Page 66 and 67:
Low Pressure O 2 Source (cont.) To
Page 68 and 69:
O 2 % (O 2 Flush) The O2% (O2 Flush
Page 70 and 71:
On/Standby This button switches the
Page 72 and 73:
Pressure Control This control estab
Page 74 and 75:
Select Use this button to change th
Page 76 and 77:
Set Value Knob Use the Set Value kn
Page 78 and 79:
Tidal Volume Use the Tidal Volume c
Page 80 and 81:
Page 6-30 LTV ® 1200 Ventilator Op
Page 82 and 83:
Battery Level The Battery Level ind
Page 84 and 85: Charge Status The Charge Status ind
Page 86 and 87: NPPV The NPPV 30 indicator LED is l
Page 88 and 89: Automatic or Manual Data Display Sc
Page 90 and 91: I:Ecalc xx:xx The Calculated I:E ra
Page 92 and 93: Alarms APNEA, APNEA xx bpm When the
Page 94 and 95: BAT EMPTY (cont.) NOTE When the bat
Page 96 and 97: BAT LOW (cont) NOTE Internal Batter
Page 98 and 99: DEFAULTS (cont.) The factory-set de
Page 100 and 101: DISC/SENSE When the ventilator dete
Page 102 and 103: HIGH O 2 PRES When the average oxyg
Page 104 and 105: HIGH PRES When the pressure in the
Page 106 and 107: HW FAULT When the ventilator detect
Page 108 and 109: LOW MIN VOL When the exhaled minute
Page 110 and 111: LOW PEEP When the patient circuit p
Page 112 and 113: NO CAL DATA, NO CAL Monitor Display
Page 114 and 115: POWER LOW When the ventilator is op
Page 116 and 117: RESET / RESET 1 A RESET or a RESET
Page 118 and 119: SBT > f When the Spontaneous Breath
Page 120 and 121: SBT > f/Vt When the Spontaneous Bre
Page 122 and 123: XDCR FAULT When a transducer autoze
Page 124 and 125: H&L PEEP OFF The H&L PEEP OFF messa
Page 126 and 127: LO f/Vt OFF The LO f/Vt OFF message
Page 128 and 129: SBT TIME The SBT TIME message is di
Page 130 and 131: Navigating the Extended Features Me
Page 132 and 133: Apnea Interval Use this menu item t
Page 136 and 137: Variable Rise Time Use the Variable
Page 138 and 139: Variable Time Termination Use the V
Page 140 and 141: Leak Compensation Use the Leak Comp
Page 142 and 143: O 2 Flush Use the O2 Flush option t
Page 144 and 145: Software Version Use the Software V
Page 146 and 147: Set Time Use the Set Time option to
Page 148 and 149: Valve Home Position Use the Valve H
Page 150 and 151: O 2 Cylinder Duration (cont.) 4) Tu
Page 152 and 153: LTV ® 1200 Presets Table Feature/F
Page 154 and 155: SBT Operations (cont.) When the Spo
Page 156 and 157: Transducer Autozero Use the Transdu
Page 158 and 159: Exhalation Flow Transducer Differen
Page 160 and 161: Real Time Transducers Use the Real
Page 162 and 163: Page 10-34 LTV ® 1200 Ventilator O
Page 164 and 165: To enable the Ventilator Checkout m
Page 166 and 167: Display Test Use the Display Test t
Page 168 and 169: Control Test Use the Control Test t
Page 170 and 171: Leak Test Use the Leak Test to test
Page 172 and 173: Vent Inop Alarm Test Use the Vent I
Page 174 and 175: Exit To exit the vent check mode an
Page 176 and 177: To Turn the Ventilator On (cont.) I
Page 178 and 179: Procedure for Control Mode Set Up S
Page 180 and 181: Procedure for SIMV Mode Set Up Set
Page 182 and 183: Procedure for NPPV Mode Set Up Set
Page 184 and 185:
LTV ® Ventilator Settings Checklis
Page 186 and 187:
Cleaning or replacing the Fan Filte
Page 188 and 189:
Cleaning or Replacing the O 2 Inlet
Page 190 and 191:
Cleaning the Exhalation Valve and R
Page 192 and 193:
ATTENTION Nettoyage du piège à ea
Page 194 and 195:
To clean the exhalation valve, sens
Page 196 and 197:
Page 13-12 LTV ® 1200 Ventilator O
Page 198 and 199:
Using the AC Adapter To run the ven
Page 200 and 201:
2) Connect the power connector on t
Page 202 and 203:
Using the Automobile Cigarette Ligh
Page 204 and 205:
CAUTION Release Button - To avoid d
Page 206 and 207:
Replacing the Automobile Adapter Fu
Page 208 and 209:
Caring for the Internal Battery The
Page 210 and 211:
Displays and Buttons Some of the sy
Page 212 and 213:
Symptoms Possible Causes What to Do
Page 214 and 215:
Ventilator Performance Symptoms Pos
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
Problem Possible Causes What To Do
Page 226 and 227:
Alarm Name Displayed Alarm Priority
Page 228 and 229:
Page 230 and 231:
Page 232 and 233:
Page 234 and 235:
Page 236 and 237:
MR Conditional System - Conditions
Page 238 and 239:
WARNING • Put the MR Conditional
Page 240 and 241:
Control Range Tolerance PIP LED Dis
Page 242 and 243:
Fixed Alarms Control Range Toleranc
Page 244 and 245:
Displays Packaging Display Range To
Page 246 and 247:
Power Feature Range Tolerance / Ind
Page 248 and 249:
Page A-10 LTV ® 1200 Ventilator Op
Page 250 and 251:
Service Assistance For assistance i
Page 252 and 253:
Protective Boots Rubberized protect
Page 254 and 255:
• Item (1), Protective Boot, Uppe
Page 256 and 257:
Protective Boot Installation Suppli
Page 258 and 259:
To Install the Lower Protective Boo
Page 260 and 261:
Patient Breathing Circuit - Connect
Page 262 and 263:
Oxygen Lines - Connection Instructi
Page 264 and 265:
Patient Assist Call System - Connec
Page 266 and 267:
Using the Remote Alarm Cable Use th
Page 268 and 269:
Checking the Ventilator for Proper
Page 270 and 271:
Ventilator Proper Operation Workshe
Page 272 and 273:
Page C-22 LTV ® 1200 Ventilator Op
Page 274 and 275:
Ventilation flow enters the Flow Va
Page 276 and 277:
5) Push the Select button. • xx:e
Page 278 and 279:
Code Event Name Event Associated Al
Page 280 and 281:
Event Codes by Event Name Event Nam
Page 282 and 283:
Event Name Code Event Associated Al
Page 284 and 285:
TERM DEFINITION Control mode A vent
Page 286 and 287:
TERM DEFINITION PIP Peak Inspirator
Page 288 and 289:
Page F-6 LTV ® 1200 Ventilator Ope
Page 290 and 291:
Button Controls · 5-3 C Calculated
Page 292 and 293:
Mean Airway Pressure · 8-2, 8-3 Mi
Page 294:
X XDCR FAULT · 9-32, 15-21 XDCR ZE
show all

LTV 1200 Operator's Manual - CareFusion Emergency Preparedness

Create successful ePaper yourself

Delete template?

Save as template?