LTV 1200 Operator's Manual - CareFusion Emergency Preparedness

Recommendations

Info

Control Locking The front panel controls may be locked so that settings cannot be accidentally changed. When the controls are locked, the Control Lock LED will be on. If you try to select or change a control while the Control Lock is on, the message LOCKED will be displayed in the display window and the Control Lock LED will flash. Two different levels of difficulty can be set for control unlocking: Easy and Hard. The Easy unlocking method should be used when only trained personnel have access to the ventilator. The Hard method should be used when children or others may have access to the ventilator and you want to prevent accidental changes to the control settings. Easy unlocking is the default and this setting is changed using the Extended Features menus 11 . To turn the Control Lock on: 1) Push the Control Lock button. The Control Lock LED is on whenever the front panel controls are locked. If you push a button while the controls are locked: 1) The Control Lock LED will flash. 2) LOCKED will be displayed in the display window. 3) The button push is ignored. To turn the Control Lock off with Easy unlocking: 1) Push the Control Lock button. To turn the Control Lock off with Hard unlocking: 1) Push and hold the Control Lock button for 3 seconds. These controls are not affected by the Control Lock and operate even when the Control Lock is on: Manual Breath, Silence Reset, Select. NOTE The Control Lock button also serves as an “escape” key from the Extended Menu. REMARQUE Le bouton de verrouillage sert aussi de touche d'échappement pour quitter le menu Fonctions avancées. Control Retention Once a control value is set, that value will be retained in non-volatile memory 12 . The settings retained in non-volatile memory may be used when the ventilator is next powered up. 11 See Chapter 10 - Extended Features, Control Unlock for more information. 12 Non-volatile memory is memory that is not erased when the ventilator is turned off or disconnected. Page 5-6 LTV ® 1200 Ventilator Operator’s Manual p/n 18247-001, Rev. G
Chapter 6 - CONTROLS This section explains how each of the LTV ® 1200 ventilator front panel controls work. Assist/Control - SIMV/CPAP - NPPV This button toggles between Assist/Control, SIMV/CPAP, and NPPV modes of ventilation. Each press of the button advances or confirms your selection as follows: • One press selects the first mode in the series (Assist/Control) and the associated LED flashes. A second press confirms the selection and the associated LED lights solid. • If you press the button again, the SIMV/CPAP LED flashes. Pressing again confirms and causes the SIMV/CPAP LED to light solid green. • Press once more to select NPPV mode and the NPPV LED flashes. To confirm NPPV mode you must press again but be aware that the NPPV LED will continue to flash until the IPAP and EPAP values have been set. • For more information see Procedure for NPPV Mode Set Up, in Chapter 12 – Operating Procedure. NOTE When Assist/Control is selected, the ventilator will be in Control or Assist/Control mode, depending on the Sensitivity setting. • If Sensitivity is set to dashes “- -”, the ventilator will be operating in Control mode. • If Sensitivity is set to any other value, the ventilator will be operating in Assist/Control mode. When SIMV/CPAP is selected, the ventilator will be in SIMV or CPAP mode, depending on the Breath Rate setting. • If Breath Rate is set to dashes “- -”, the ventilator will be operating in CPAP mode. • If Breath Rate is set to any other value, the ventilator will be operating in SIMV mode. REMARQUE Lorsque Aide / Contrôle est sélectionné, le ventilateur sera en mode Contrôle ou Aide, selon le réglage de la sensibilité. • Si la sensibilité est réglée sur Traits « - - », le ventilateur fonctionnera en mode Contrôle. • Si la sensibilité est réglée sur toute autre valeur, le ventilateur fonctionnera en mode Aide / Contrôle. Lorsque le mode SIMV/CPAP est sélectionné, le ventilateur sera en mode SIMV ou CPAP, selon le réglage du débit respiratoire. • Si le débit respiratoire est réglé sur Traits « - - », le ventilateur fonctionnera en mode CPAP. • Si le débit respiratoire est réglé sur toute autre valeur, le ventilateur fonctionnera en mode SIMV. Operator’s Manual LTV ® 1200 Ventilator Page 6-1 p/n 18247-001, Rev. G
Page 1: LTV ® 1200 Ventilator / MR Conditi
Page 4 and 5: Warranty Pulmonetic Systems warrant
Page 6 and 7: Notice To Operators Unsafe Operatio
Page 8 and 9: Chapter 6 - Controls...............
Page 10 and 11: LPPS OFF...........................
Page 12 and 13: Chapter 15 - Troubleshooting ......
Page 14 and 15: Operator’s Safety Information All
Page 16 and 17: WARNING Battery run time - When the
Page 18 and 19: AVERTISSEMENT Personnel non qualifi
Page 20 and 21: AVERTISSEMENT Concentration d’oxy
Page 22 and 23: Cautions CAUTION Ventilator Sterili
Page 24 and 25: CAUTION External Battery Pack - The
Page 26 and 27: ATTENTION Nettoyage du panneau fron
Page 28 and 29: Symbols Symbol Compliance 3 Title A
Page 30 and 31: Indications for Use The LTV ® 1200
Page 32 and 33: Information/Assistance For addition
Page 34 and 35: Volume Control Breaths For Volume C
Page 36 and 37: Pressure Control Breaths (cont) Pre
Page 38 and 39: Spontaneous Breaths For Spontaneous
Page 40 and 41: SIMV Mode SIMV mode is selected whe
Page 42 and 43: NPPV Mode Non-invasive Positive Pre
Page 44 and 45: Volume Pressure Ventilation The LTV
Page 46 and 47: Setting a Control There are 5 kinds
Page 48 and 49: Bright, Dim and Blank Control Displ
Page 52 and 53: Breath Rate Use the Breath Rate con
Page 54 and 55: High Pressure Limit Use the High Pr
Page 56 and 57: Inspiratory Hold An Inspiratory Hol
Page 58 and 59: Expiratory Hold An Expiratory Hold
Page 60 and 61: Inspiratory Time This control sets
Page 62 and 63: Low Pressure The Low Pressure alarm
Page 64 and 65: Low Pressure O 2 Source (cont.) NOT
Page 66 and 67: Low Pressure O 2 Source (cont.) To
Page 68 and 69: O 2 % (O 2 Flush) The O2% (O2 Flush
Page 70 and 71: On/Standby This button switches the
Page 72 and 73: Pressure Control This control estab
Page 74 and 75: Select Use this button to change th
Page 76 and 77: Set Value Knob Use the Set Value kn
Page 78 and 79: Tidal Volume Use the Tidal Volume c
Page 80 and 81: Page 6-30 LTV ® 1200 Ventilator Op
Page 82 and 83: Battery Level The Battery Level ind
Page 84 and 85: Charge Status The Charge Status ind
Page 86 and 87: NPPV The NPPV 30 indicator LED is l
Page 88 and 89: Automatic or Manual Data Display Sc
Page 90 and 91: I:Ecalc xx:xx The Calculated I:E ra
Page 92 and 93: Alarms APNEA, APNEA xx bpm When the
Page 94 and 95: BAT EMPTY (cont.) NOTE When the bat
Page 96 and 97: BAT LOW (cont) NOTE Internal Batter
Page 98 and 99: DEFAULTS (cont.) The factory-set de
Page 100 and 101:
DISC/SENSE When the ventilator dete
Page 102 and 103:
HIGH O 2 PRES When the average oxyg
Page 104 and 105:
HIGH PRES When the pressure in the
Page 106 and 107:
HW FAULT When the ventilator detect
Page 108 and 109:
LOW MIN VOL When the exhaled minute
Page 110 and 111:
LOW PEEP When the patient circuit p
Page 112 and 113:
NO CAL DATA, NO CAL Monitor Display
Page 114 and 115:
POWER LOW When the ventilator is op
Page 116 and 117:
RESET / RESET 1 A RESET or a RESET
Page 118 and 119:
SBT > f When the Spontaneous Breath
Page 120 and 121:
SBT > f/Vt When the Spontaneous Bre
Page 122 and 123:
XDCR FAULT When a transducer autoze
Page 124 and 125:
H&L PEEP OFF The H&L PEEP OFF messa
Page 126 and 127:
LO f/Vt OFF The LO f/Vt OFF message
Page 128 and 129:
SBT TIME The SBT TIME message is di
Page 130 and 131:
Navigating the Extended Features Me
Page 132 and 133:
Apnea Interval Use this menu item t
Page 134 and 135:
Patient Assist Use the PNT ASSIST m
Page 136 and 137:
Variable Rise Time Use the Variable
Page 138 and 139:
Variable Time Termination Use the V
Page 140 and 141:
Leak Compensation Use the Leak Comp
Page 142 and 143:
O 2 Flush Use the O2 Flush option t
Page 144 and 145:
Software Version Use the Software V
Page 146 and 147:
Set Time Use the Set Time option to
Page 148 and 149:
Valve Home Position Use the Valve H
Page 150 and 151:
O 2 Cylinder Duration (cont.) 4) Tu
Page 152 and 153:
LTV ® 1200 Presets Table Feature/F
Page 154 and 155:
SBT Operations (cont.) When the Spo
Page 156 and 157:
Transducer Autozero Use the Transdu
Page 158 and 159:
Exhalation Flow Transducer Differen
Page 160 and 161:
Real Time Transducers Use the Real
Page 162 and 163:
Page 10-34 LTV ® 1200 Ventilator O
Page 164 and 165:
To enable the Ventilator Checkout m
Page 166 and 167:
Display Test Use the Display Test t
Page 168 and 169:
Control Test Use the Control Test t
Page 170 and 171:
Leak Test Use the Leak Test to test
Page 172 and 173:
Vent Inop Alarm Test Use the Vent I
Page 174 and 175:
Exit To exit the vent check mode an
Page 176 and 177:
To Turn the Ventilator On (cont.) I
Page 178 and 179:
Procedure for Control Mode Set Up S
Page 180 and 181:
Procedure for SIMV Mode Set Up Set
Page 182 and 183:
Procedure for NPPV Mode Set Up Set
Page 184 and 185:
LTV ® Ventilator Settings Checklis
Page 186 and 187:
Cleaning or replacing the Fan Filte
Page 188 and 189:
Cleaning or Replacing the O 2 Inlet
Page 190 and 191:
Cleaning the Exhalation Valve and R
Page 192 and 193:
ATTENTION Nettoyage du piège à ea
Page 194 and 195:
To clean the exhalation valve, sens
Page 196 and 197:
Page 13-12 LTV ® 1200 Ventilator O
Page 198 and 199:
Using the AC Adapter To run the ven
Page 200 and 201:
2) Connect the power connector on t
Page 202 and 203:
Using the Automobile Cigarette Ligh
Page 204 and 205:
CAUTION Release Button - To avoid d
Page 206 and 207:
Replacing the Automobile Adapter Fu
Page 208 and 209:
Caring for the Internal Battery The
Page 210 and 211:
Displays and Buttons Some of the sy
Page 212 and 213:
Symptoms Possible Causes What to Do
Page 214 and 215:
Ventilator Performance Symptoms Pos
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
Problem Possible Causes What To Do
Page 226 and 227:
Alarm Name Displayed Alarm Priority
Page 228 and 229:
Page 230 and 231:
Page 232 and 233:
Page 234 and 235:
Page 236 and 237:
MR Conditional System - Conditions
Page 238 and 239:
WARNING • Put the MR Conditional
Page 240 and 241:
Control Range Tolerance PIP LED Dis
Page 242 and 243:
Fixed Alarms Control Range Toleranc
Page 244 and 245:
Displays Packaging Display Range To
Page 246 and 247:
Power Feature Range Tolerance / Ind
Page 248 and 249:
Page A-10 LTV ® 1200 Ventilator Op
Page 250 and 251:
Service Assistance For assistance i
Page 252 and 253:
Protective Boots Rubberized protect
Page 254 and 255:
• Item (1), Protective Boot, Uppe
Page 256 and 257:
Protective Boot Installation Suppli
Page 258 and 259:
To Install the Lower Protective Boo
Page 260 and 261:
Patient Breathing Circuit - Connect
Page 262 and 263:
Oxygen Lines - Connection Instructi
Page 264 and 265:
Patient Assist Call System - Connec
Page 266 and 267:
Using the Remote Alarm Cable Use th
Page 268 and 269:
Checking the Ventilator for Proper
Page 270 and 271:
Ventilator Proper Operation Workshe
Page 272 and 273:
Page C-22 LTV ® 1200 Ventilator Op
Page 274 and 275:
Ventilation flow enters the Flow Va
Page 276 and 277:
5) Push the Select button. • xx:e
Page 278 and 279:
Code Event Name Event Associated Al
Page 280 and 281:
Event Codes by Event Name Event Nam
Page 282 and 283:
Event Name Code Event Associated Al
Page 284 and 285:
TERM DEFINITION Control mode A vent
Page 286 and 287:
TERM DEFINITION PIP Peak Inspirator
Page 288 and 289:
Page F-6 LTV ® 1200 Ventilator Ope
Page 290 and 291:
Button Controls · 5-3 C Calculated
Page 292 and 293:
Mean Airway Pressure · 8-2, 8-3 Mi
Page 294:
X XDCR FAULT · 9-32, 15-21 XDCR ZE
show all

LTV 1200 Operator's Manual - CareFusion Emergency Preparedness

Create successful ePaper yourself

Delete template?

Save as template?