Master Control - Berker

More documents

Recommendations

Info

Message list If necessary, it can be set in the parameters whether each fault message should be saved in the message list of the panel. The message list is a separate system page which can be reached by opening a page using any function button. The following events of a fault can be logged in the message list... - Time of the fault message, logged as "coming", - Time the fault message is retracted (fault cause eliminated), logged as "going". - Time of acknowledgement, logged as "acknowledged". In addition, the "Fault text" is logged and displayed in the message list, thus allowing clear identification. Which of the three named events is logged in the message list can be configured in the "Message list" parameter group of a fault message. i The message list is deleted during a programming operation of the panel by the ETS or the plug-in. If the power supply fails, the events stored in the message list are not lost. Order-No. 7574 00 1X Software "...590101" Functional description Page 82 of 222
4.2.4.5 Light scene function Introduction The panel can managed up to 24 light scenes with up to 32 light scene groups (actuator groups). The light scenes can be controlled both using the operation functions of the panel and using an extension object. <strong>Control</strong> using the extension object is only possible when, in the "Light scenes" parameter node, the "Extension object" parameter is set to "Yes". The extension object can be used both to open and to save the light scenes. The ETS plug-in automatically assigns the numbers 1 to 24 to the defined light scenes. Other numbers are not supported. When the light scenes are opened, the panel sends a telegram to each light scene group with the value saved in the panel. When the light scenes are changed later, the panel can send a read request to each light scene group and save the responses as new values in non-volatile memory. Opening and saving light scenes can lead to a short-term increase in bus load. For this reason, it is possible to use the general parameters of the ETS plug-in to specify the time between the individual light scene telegrams (see chapter 4.2.4.1.1. General parameters). Project planning of the light scene function consists primarily of three steps... - Adding the light scenes to the plug-in project planning. - Adding the light scene groups to the plug-in project planning. - Specifying the light scene values on the panel. i The following should be observed: If, after successful commissioning, changes are made to the light scenes or the light scene groups in the ETS plug-in, then these changes must be loaded into the device in a valid way. The light scene configuration is only programmed completely when the parameter "Overwrite light scene name, delete values" in the top parameter node of the plug-in is set to "Yes" (see chapter 4.2.4.1.4. Download behaviour). Any changes made on the panel by the user (light scene values, light scene designations) are lost. 4.2.4.5.1 Adding light scenes and light scene groups Adding light scenes Firstly, the light scenes must be created. Three screen pages are available in the ETS plug-in under the node "Light scenes -> Light scene collection". Up to eight light scenes can be added to each of these three pages by clicking the right mousebutton. For additional clarity, these light scenes should be given clear designations straight after adding. These designations can be modified at any later time on the panel after commissioning. On adding, the light scenes receive their light scene number automatically, with which they can be opened later using the extension object. The light scenes do not otherwise possess any additional parameters or configuration options. The light scene groups are later assigned to each light scene, meaning that control is possible by the KNX / EIB actuator groups. i During panel operation, the three screen pages of the light scene collection can only be reached by jumping to the light scene pages (1...3). Therefore it is necessary to configure at least one function button of a display to open a light scene page. Otherwise it is not possible to set up the light scene values on the panel at a later time. Navigation between the light scene pages is made possible by the scroll bar, assuming it is shown. Order-No. 7574 00 1X Software "...590101" Functional description Page 83 of 222
Page 1 and 2:
Master Control Issue: 23.10.2008 13
Page 3 and 4:
4.2.4.10.2 Datalogger display .....
Page 5 and 6:
1.3 Accessories Flush-mounting box
Page 7 and 8:
2.2 Device components Order-No. 757
Page 9 and 10:
o Insert the device in the installa
Page 11 and 12:
device parameter view in the ETS. T
Page 13 and 14:
- Operating elements are used for n
Page 15 and 16:
4 Software description 4.1 Software
Page 17 and 18:
- Up 24 light scenes with a total o
Page 19 and 20:
4.2.3 Object table Number of commun
Page 21 and 22:
Function: Date / time request by ex
Page 23 and 24:
Function: Value function Object h F
Page 25 and 26:
Function: Restraint function Object
Page 27 and 28:
Function: Fault message Object h Fu
Page 29 and 30:
Function: Multiplexer Object h Func
Page 31 and 32: Objects for presence simulation Fun
Page 33 and 34: Function: Signalling system Object
Page 35 and 36: Function: Signalling system Object
Page 37 and 38: 4.2.4 Functional description Introd
Page 39 and 40: The individual screen pages and the
Page 41 and 42: 16 characters. The box can also be
Page 43 and 44: 4.2.4.1.3 Date and time The panel p
Page 45 and 46: 4.2.4.1.4 Download behaviour After
Page 47 and 48: 4.2.4.1.6 Image list The panel can
Page 49 and 50: 4.2.4.1.7 Preview and resource moni
Page 51 and 52: The largest area is the Content are
Page 53 and 54: Service page, version 57 Service pa
Page 55 and 56: Display function The settings in th
Page 57 and 58: Order-No. 7574 00 1X picture 12: Da
Page 59 and 60: Order-No. 7574 00 1X picture 13: Te
Page 61 and 62: The parameters of the display eleme
Page 63 and 64: carried out. There is an automatic
Page 65 and 66: 4.2.4.2.4 Copying display elements
Page 67 and 68: 4.2.4.3 Service page 4.2.4.3.1 Stru
Page 69 and 70: - Service address: an address can b
Page 71 and 72: Text displayed in the history Meani
Page 73 and 74: IP ID code Meaning 0x40 e-mail test
Page 75 and 76: 4.2.4.3.4 Passwords The passwords a
Page 77 and 78: tem) helps. Here, allocations of IP
Page 79 and 80: 4.2.4.4 Fault messages Fault messag
Page 81: 4.2.4.4.2 Acknowledgement and messa
Page 85 and 86: 4.2.4.5.2 Specifying light scene va
Page 87 and 88: 4.2.4.6 Timer switch function Timer
Page 89 and 90: 4.2.4.6.2 Setting switching times T
Page 91 and 92: Order-No. 7574 00 1X picture 26: Wi
Page 93 and 94: i In 12 hour time display format, t
Page 95 and 96: 4.2.4.8 Logical links The panel has
Page 97 and 98: 4.2.4.9 Multiplexer The panel has t
Page 99 and 100: 4.2.4.10 Datalogger Introduction Th
Page 101 and 102: It should always be noticed that al
Page 103 and 104: 4.2.4.10.2 Datalogger display The d
Page 105 and 106: 4.2.4.11 Presence simulation Introd
Page 107 and 108: i During the recording phase, chang
Page 109 and 110: start delay is displayed in the sta
Page 111 and 112: i External switching units are comp
Page 113 and 114: A distinction is made between the f
Page 115 and 116: 4.2.4.12.2 Detector Detector types
Page 117 and 118: The following events are shown summ
Page 119 and 120: 4.2.4.12.3 Arming Arming/unarming t
Page 121 and 122: - "Arming acknowledgement": This ob
Page 123 and 124: Subsequent alarm If an additional d
Page 125 and 126: 4.2.4.12.6 Event memory The signall
Page 127 and 128: 4.2.4.13 e-mail messages 4.2.4.13.1
Page 129 and 130: Order-No. 7574 00 1X picture 39: Sy
Page 131 and 132: General information on e-mail text
Page 133 and 134:
Sending the data values of the data
Page 135 and 136:
4.2.4.14.2 Displaying RSS newsfeeds
Page 137 and 138:
Order-No. 7574 00 1X picture 44: Di
Page 139 and 140:
4.2.4.15 Group addresses On startin
Page 141 and 142:
4.2.5 Parameters Description Values
Page 143 and 144:
Status poll delay after start (x 5
Page 145 and 146:
Basic brightness Off Dark Light h D
Page 147 and 148:
Request date / time No Yes Request
Page 149 and 150:
Wallpaper No presetting Pressing ".
Page 151 and 152:
Vertical icon alignment Top Centred
Page 153 and 154:
Value alignment Left-align Centred
Page 155 and 156:
For "Blind" display function... Sta
Page 157 and 158:
Order-No. 7574 00 1X with plus/minu
Page 159 and 160:
Upper limit value No Yes Order-No.
Page 161 and 162:
For "Date" display function... Sour
Page 163 and 164:
Curve 1 / 2: Datalogger channel Cur
Page 165 and 166:
Y axis Min. axis scaling Y axis Max
Page 167 and 168:
Value alignment Left-align Centred
Page 169 and 170:
Icon for frost / heat protection Ic
Page 171 and 172:
Image text for 1 'Capacitive' Image
Page 173 and 174:
Order-No. 7574 00 1X on the screen.
Page 175 and 176:
Order-No. 7574 00 1X to "0...100 %"
Page 177 and 178:
Time base between switching and dim
Page 179 and 180:
h Service page -> Area 1 Order-No.
Page 181 and 182:
Event display image text on Bit = 1
Page 183 and 184:
For "ASCII text" function... Length
Page 185 and 186:
Switching time x (x = 1...8) Order-
Page 187 and 188:
In case of fault message, blockage
Page 189 and 190:
Enter 'Departing' Yes No Enter 'Ack
Page 191 and 192:
Blocking object available Behaviour
Page 193 and 194:
Order-No. 7574 00 1X DPT 5,001 …
Page 195 and 196:
Order-No. 7574 00 1X sponse telegra
Page 197 and 198:
Contents (max. 60 characters) Recip
Page 199 and 200:
Internal arming via the signal page
Page 201 and 202:
Alarm delay time, external [s] Prea
Page 203 and 204:
Heading [Light scene group - Page 1
Page 205 and 206:
Creating a new project file If a pa
Page 207 and 208:
- "IP" tab The IP communication par
Page 209 and 210:
i The project file is temporary and
Page 211 and 212:
(8 bit values) for easier comprehen
Page 213 and 214:
Settings If the "IP" item is opened
Page 215 and 216:
Mailbox poll: The panel cyclically
Page 217 and 218:
i The set RSS newsfeed parameters a
Page 219 and 220:
i The panel can only be operated re
Page 221 and 222:
Objects for datalogger .. .........
show all

Master Control - Berker

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?