PowerFlex 750-Series AC Drives User Manual

3-138 Programming and ParametersFileGroupNameNo. Description5 Dig Out StsDigital Output StatusStatus of the digital outputs.ValuesRead-WriteData TypeOptionsReservedReservedReservedReservedReservedReservedReservedReservedReservedReservedReservedReservedReservedTrans Out 1 (2)Trans Out 0 (1)Default 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0Relay Out 00 = Output De-energized1 = Output Energized(1) Bit 1 = “Trans Out 0” for I/O Module model 20-750-2263C-1R2T= “Relay Out 1” for I/O Module models 20-750-2262C-2R and 20-750-2262D-2R(2) Bit 2 is only used by I/O Module 20-750-2263C-1R2T6 Dig Out InvertDigital Output InvertInverts the selected digital output.HOST GROUPSDigital OutputsOptionsReservedReservedReservedReservedReservedReservedReservedReservedReservedReservedReservedReservedReservedTrans Out 1 (2)Trans Out 0 (1)Default 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0(1) Bit 1 = “Trans Out 0” for I/O Module model 20-750-2263C-1R2T= “Relay Out 1” for I/O Module models 20-750-2262C-2R and 20-750-2262D-2R(2) Bit 2 is only used by I/O Module 20-750-2263C-1R2T7 Dig Out SetpointDigital Output SetpointControls Relay or Transistor Outputs when chosen as the source. Can be used to control outputs from a communication device using DataLinks.Relay Out 00 = Output Not Inverted1 = Output InvertedOptionsReservedReservedReservedReservedReservedReservedReservedReservedReservedReservedReservedReservedReservedTrans Out 1 (2)Trans Out 0 (1)Default 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0Relay Out 00 = Output De-energized1 = Output Energized(1) Bit 1 = “Trans Out 0” for I/O Module model 20-750-2263C-1R2T= “Relay Out 1” for I/O Module models 20-750-2262C-2R and 20-750-2262D-2R(2) Bit 2 is only used by I/O Module 20-750-2263C-1R2T10 RO0 SelRelay Output 0 SelectSelects the source that will energize the relay output.Any status parameter bit can be used as an output source. For example P935[Drive Status 1] bit 7 “Faulted”.11 RO0 Level SelRelay Output 0 Level SelectSelects the source of the level that will be compared.12 RO0 LevelRelay Output 0 LevelSets the level compare value.Default: 0.00 (Disabled)Min/Max: 0.00 / 159999.15Default: 0 (Disabled)Min/Max: 0 / 159999Default: 0.0Min/Max: –/+1000000.0RW 32-bitIntegerRW 32-bitIntegerRW RealPowerFlex 750-Series User Manual – Publication 750-UM001C-EN-P – September 2009