PowerFlex 750-Series AC Drives User Manual

Troubleshooting 4-17EventFault ConfigurationNo. (1) Fault/Alarm Text Type Action Paramxx210 Ch1 IntOfst Err Configurable P39[FB1 Loss Cfg]xx211 Ch1 DataTabl Err Configurable P39[FB1 Loss Cfg]xx212 Ch1 AnalLim Err Configurable P39[FB1 Loss Cfg]xx213 Ch1 Int I2C Err Configurable P39[FB1 Loss Cfg]xx214 Ch1 IntChksm Err Configurable P39[FB1 Loss Cfg]xx215 Ch1 PrgmResetErr Configurable P39[FB1 Loss Cfg]xx216 Ch1 CntOvrflwErr Configurable P39[FB1 Loss Cfg]xx217 Ch1 Parity Err Configurable P39[FB1 Loss Cfg]xx218 Ch1 Chksum Err Configurable P39[FB1 Loss Cfg]xx219 Ch1 InvCmd Err Configurable P39[FB1 Loss Cfg]xx220 Ch1 SendSize Err Configurable P39[FB1 Loss Cfg]xx221 Ch1 CmdArgmt Err Configurable P39[FB1 Loss Cfg]xx222 Ch1 InvWrtAdrErr Configurable P39[FB1 Loss Cfg]xx223 Ch1 AccCode Err Configurable P39[FB1 Loss Cfg]xx224 Ch1 FieldSizeErr Configurable P39[FB1 Loss Cfg]xx225 Ch1 Address Err Configurable P39[FB1 Loss Cfg]xx226 Ch1 FieldAcc Err Configurable P39[FB1 Loss Cfg]xx228 Ch1 SiTurnPsnErr Configurable P39[FB1 Loss Cfg]xx229 Ch1 MulTrnPsnErr Configurable P39[FB1 Loss Cfg]xx236 Ch1 AnalVal Err Configurable P39[FB1 Loss Cfg]xx237 Ch1 SendCurr Err Configurable P39[FB1 Loss Cfg]xx238 Ch1 EncTemp Err Configurable P39[FB1 Loss Cfg]xx239 Ch1 Speed Err Configurable P39[FB1 Loss Cfg]xx240 Ch1 General Err Configurable P39[FB1 Loss Cfg]xx246 Ch1 LED Curr Err Configurable P39[FB1 Loss Cfg]AutoResetDescriptionError reported by Stegmann Encoder on Channel 1 withHiperface Interface - Faulty internal angular offsetError reported by Stegmann Encoder on Channel 1 withHiperface Interface - Data field partitioning table damagedError reported by Stegmann Encoder on Channel 1 withHiperface Interface - Analog limit values not availableError reported by Stegmann Encoder on Channel 1 withHiperface Interface - Internal I2C bus not operationalError reported by Stegmann Encoder on Channel 1 withHiperface Interface - Internal checksum errorError reported by Stegmann Encoder on Channel 1 withHiperface Interface - Encoder reset occurred as a result ofprogram monitoringError reported by Stegmann Encoder on Channel 1 withHiperface Interface - Counter overflowError reported by Stegmann Encoder on Channel 1 withHiperface Interface - Parity errorError reported by Stegmann Encoder on Channel 1 withHiperface Interface - Checksum of the data transmitted isincorrectError reported by Stegmann Encoder on Channel 1 withHiperface Interface - Unknown command codeError reported by Stegmann Encoder on Channel 1 withHiperface Interface - Number of data transmitted is incorrectError reported by Stegmann Encoder on Channel 1 withHiperface Interface - Command argument transmitted is notallowedError reported by Stegmann Encoder on Channel 1 withHiperface Interface - The selected data field must not bewritten to (invalid write address)Error reported by Stegmann Encoder on Channel 1 withHiperface Interface - Incorrect access codeError reported by Stegmann Encoder on Channel 1 withHiperface Interface - Size of data field stated cannot bechangedError reported by Stegmann Encoder on Channel 1 withHiperface Interface - Word address stated is outside datafieldError reported by Stegmann Encoder on Channel 1 withHiperface Interface - Access to non-existent data fieldError reported by Stegmann Encoder on Channel 1 withHiperface Interface - Single turn position unreliableError reported by Stegmann Encoder on Channel 1 withHiperface Interface - Multiple turn position unreliableError reported by Stegmann Encoder on Channel 1 withHiperface Interface - Analog value error (process data)Error reported by Stegmann Encoder on Channel 1 withHiperface Interface - Transmitter current critical (dirt, brokentransmitter)Error reported by Stegmann Encoder on Channel 1 withHiperface Interface - Encoder temperature criticalError reported by Stegmann Encoder on Channel 1 withHiperface Interface - Speed too high, no position formationpossibleError reported by a Encoder on Channel 1 with BiSSInterface - An error bit of the BiSS Single Cycle Data is setError reported by a Encoder on Channel 1 with BiSSInterface - LED current out of control rangePowerFlex 750-Series User Manual – Publication 750-UM001C-EN-P – September 2009