PowerFlex 750-Series AC Drives User Manual

Installation/Wiring 1-41750-Series I/O Module TB1 Wiring ExamplesInput/Output Connection Example Required Parameter ChangesPotentiometer UnipolarSpeed Reference10k Ohm Pot.Recommended(2k Ohm Minimum)Joystick Bipolar SpeedReference±10V InputAnalog Input BipolarSpeed Reference±10V InputAnalog Voltage InputUnipolar SpeedReference0 to +10V InputAnalog Current InputUnipolar SpeedReference0-20 mA InputCommon+Common+Common+10VC+10VAi0–Ai0+Ai0–Ai0+Ai0–Ai0+–10V10VC+10VAi0–Ai0+Ai1Ai0Ai0–Ai0+Ai1Ai0• Set Direction ModePort 0: P308 [Direction Mode] = 0 “Unipolar”• Set SelectionPort 0: P545 [Spd Ref A Sel] = Port X (I/O Module): P50 [Anlg In0 Value]• Adjust ScalingPort X (I/O Module): P51 [Anlg In0 Hi] = 10 VoltPort X (I/O Module): P52 [Anlg In0 Lo] = 0 VoltPort 0: P547 [Spd Ref A AnlgHi] = 60 HzPort 0: P548 [Spd Ref A AnlgLo] = 0 Hz• View ResultsPort X (I/O Module): P50 [Anlg In0 Value]Port 0: P592 [Selected Spd Ref]• Set Direction ModePort 0: P308 [Direction Mode] = 1 “Bipolar”• Set SelectionPort 0: P545 [Spd Ref A Sel] = Port X (I/O Module): P50 [Anlg In0 Value]• Adjust ScalingPort X (I/O Module): P51 [Anlg In0 Hi] = +10 VoltPort X (I/O Module): P52 [Anlg In0 Lo] = -10 VoltPort 0: P547 [Spd Ref A AnlgHi] = +60 HzPort 0: P548 [Spd Ref A AnlgLo] = -60 Hz• View ResultsPort X (I/O Module): P50 [Anlg In0 Value]Port 0: P592 [Selected Spd Ref]• Set Direction ModePort 0: P308 [Direction Mode] = 1 “Bipolar”• Set SelectionPort 0: P545 [Spd Ref A Sel] = Port X (I/O Module): P50 [Anlg In0 Value]• Adjust ScalingPort X (I/O Module): P51 [Anlg In0 Hi] = +10 VoltPort X (I/O Module): P52 [Anlg In0 Lo] = -10 VoltPort 0: P547 [Spd Ref A AnlgHi] = +60 HzPort 0: P548 [Spd Ref A AnlgLo] = -60 Hz• View ResultsPort X (I/O Module): P50 [Anlg In0 Value]Port 0: P592 [Selected Spd Ref]• Set Direction ModePort 0: P308 [Direction Mode] = 0 “Unipolar”• Set SelectionPort 0: P545 [Spd Ref A Sel] = Port X (I/O Module): P50 [Anlg In0 Value]• Adjust ScalingPort X (I/O Module): P51 [Anlg In0 Hi] = 10 VoltPort X (I/O Module): P52 [Anlg In0 Lo] = 0 VoltPort 0: P547 [Spd Ref A AnlgHi] = 60 HzPort 0: P548 [Spd Ref A AnlgLo] = 0 Hz• View ResultsPort X (I/O Module): P50 [Anlg In0 Value]Port 0: P592 [Selected Spd Ref]• Set Direction ModePort 0: P308 [Direction Mode] = 0 “Unipolar”• Set SelectionPort 0: P545 [Spd Ref A Sel] = Port X (I/O Module): P50 [Anlg In0 Value]• Adjust ScalingPort X (I/O Module): P51 [Anlg In0 Hi] = 20 mAPort X (I/O Module): P52 [Anlg In0 Lo] = 0 mAPort 0: P547 [Spd Ref A AnlgHi] = 60 HzPort 0: P548 [Spd Ref A AnlgLo] = 0 Hz• View ResultsPort X (I/O Module): P50 [Anlg In0 Value]Port 0: P592 [Selected Spd Ref]PowerFlex 750-Series User Manual – Publication 750-UM001C-EN-P – September 2009