PowerFlex 750-Series AC Drives User Manual

4-18 TroubleshootingEventFault ConfigurationNo. (1) Fault/Alarm Text Type Action Paramxx247 Ch1 ExMulTurnErr Configurable P39[FB1 Loss Cfg]xx248 Ch1 PsnCode Err Configurable P39[FB1 Loss Cfg]xx249 Ch1 Config Err Configurable P39[FB1 Loss Cfg]xx250 Ch1 PsnVal Err Configurable P39[FB1 Loss Cfg]xx251 Ch1 SerialComErr Configurable P39[FB1 Loss Cfg]xx252 Ch1 Ext Failure Configurable P39[FB1 Loss Cfg]xx253 Ch1 Temp Exc Err Configurable P39[FB1 Loss Cfg]xx256 Ch1 OutOfRailErr Configurable P39[FB1 Loss Cfg]xx260 Ch1 Read Head 1 Configurable P39[FB1 Loss Cfg]xx261 Ch1 Read Head 2 Configurable P39[FB1 Loss Cfg]xx262 Ch1 RAM Error Configurable P39[FB1 Loss Cfg]xx263 Ch1 EPROM Error Configurable P39[FB1 Loss Cfg]xx264 Ch1 ROM Error Configurable P39[FB1 Loss Cfg]xx266 Ch1 No Position Configurable P39[FB1 Loss Cfg]xx281 Ch1 Msg Cheksum Configurable P39[FB1 Loss Cfg]xx282 Ch1 Timeout Configurable P39[FB1 Loss Cfg]xx283 Ch1 Comm Configurable P39[FB1 Loss Cfg]xx284 Ch1 Diagnostic Configurable P39[FB1 Loss Cfg]xx285 Ch1 SpplyVltgRng Configurable P39[FB1 Loss Cfg]xx286 Ch1 SC Amplitude Configurable P39[FB1 Loss Cfg]xx287 Ch1 Open Wire Configurable P39[FB1 Loss Cfg]xx288 Ch1 Quad Loss Configurable P39[FB1 Loss Cfg]xx289 Ch1 Phase Loss Configurable P39[FB1 Loss Cfg]xx290 Ch1 Unsupp Enc Configurable P39[FB1 Loss Cfg]xx300 Ch1 FreqExc Alm Alarm 1 P39[FB1 Loss Cfg]AutoResetDescriptionError reported by a Encoder on Channel 1 with BiSSInterface - External multiturn errorError reported by a Encoder on Channel 1 with BiSSInterface - Position code error (single step error)Error reported by a Encoder on Channel 1 with BiSSInterface - failure configuring interfaceError reported by a Encoder on Channel 1 with BiSSInterface - Position data not validError reported by a Encoder on Channel 1 with BiSSInterface - Serial interface failureError reported by a Encoder on Channel 1 with BiSSInterface - External failure over NERRError reported by a Encoder on Channel 1 with BiSSInterface - Temperature out of defined rangeError reported by a linear Stahl encoder on Channel 1 - Railis no longer present between the read headError reported by a linear Stahl encoder on Channel 1 -Indicates that the read head must be cleaned or installedcorrectlyError reported by a linear Stahl encoder on Channel 1 -Indicates that the read head must be cleaned or installedcorrectlyError reported by a linear Stahl encoder on Channel 1 -Indicates a RAM error. Reading head needs to be repairedError reported by a linear Stahl encoder on Channel 1 -Indicates a EPROM error. Reading head needs to berepairedError reported by a linear Stahl encoder on Channel 1 -Indicates a ROM error. Reading head needs to be repairedError reported by a linear Stahl encoder on Channel 1 -Indicates that no position value was available - only possiblefollowing powerup or resetIndicates the option card has detected a serialcommunications checksum error while attempting tocommunicate with the encoder on channel 1.Indicates the option card has detected a serialcommunications timeout error while attempting tocommunicate with the encoder on channel 1.Indicates the option card has detected a serialcommunications error (other than checksum or timeout)while attempting to communicate with the encoder onchannel 1.Indicates the option card has detected a powerup diagnostictest failure for encoder channel 1.Indicates that the voltage source to the encoder 1 is out ofrange.Indicates that the encoder 1 signal amplitude is out oftolerance.Indicates that an open wire condition has been detected forencoder 1.Indicates that a signal quadrature error has been detectedfor encoder 1Indicates that an A or B signal of an A quad B incrementalencoder on Channel 1 is disconnected.Indicates that the connected encoder on Channel 1 is notsupportedAlarm reported by Heidenhain Encoder on Channel 1 withEnDat Interface - Frequency exceeded warningPowerFlex 750-Series User Manual – Publication 750-UM001C-EN-P – September 2009