PowerFlex 750-Series AC Drives User Manual

3-182 Programming and ParametersFileGroupNameNo. Description78 755 Logic Src CfgLogic Source ConfigureControls which of the peer-to-drive Datalinks contain the Logic Command for thedrive.79 755 Ref Src CfgReference Source ConfigureControls which of the peer-to-drive Datalinks contain the Reference for the drive.80 755 Fr Peer Timeout81828384From Peer TimeoutSets the timeout for a Peer I/O connection. If the time is reached without theadapter receiving (consuming) a message, the adapter will respond with theaction specified in P56 [Peer Flt Action].In an adapter receiving (consuming) Peer I/O, the value of this parameter must begreater than the product of the value of P89 [To Peer Period] in the adaptertransmitting (producing) Peer I/O multiplied by the value of P90 [To Peer Skip] inthe adapter transmitting (producing) Peer I/O.755755755Fr Peer Addr 1Fr Peer Addr 2Fr Peer Addr 3Fr Peer Addr 4755From Peer Address 1…4Sets the bytes in the IP address that specifies the device from which the adapterreceives (consumes) Peer I/O data.255 . 255 . 255 . 255ValuesDefault: 0Min/Max: 0 / 16Default: 0Min/Max: 0 / 16Units: SecsDefault: 10.00Min/Max: 0.01 / 10.00Default: 0Min/Max: 0 / 255Read-WriteData TypeRW RealRW RealRW RealRW RealHOST GROUPS[Peer Inp Addr 1][Peer Inp Addr 2][Peer Inp Addr 3][Peer Inp Addr 4]Important: The Peer Inp Addr must be on the same subnet as the embeddedEtherNet/IP adapter.Changes to these parameters are ignored when P85 [Fr Peer Enable] is “1” (On).85 755 Fr Peer EnableFrom Peer EnableControls whether Peer I/O input is operating. A value of 0 “Off” turns off Peer I/Oinput. A value of 1 “Cmd/Ref” overrides the settings in Parameters P76 [DLs FrPeer Cfg], P78 [Logic Src Cfg], and P79 [Ref Src Cfg] and automatically usespeer Datalink 01 as the drive's present Logic Command and peer Datalink 02 asthe drive's Reference. A value of 2 “Custom” enables peer I/O input using theDatalink count and settings provided by the user.86 755 Fr Peer StatusFrom Peer StatusDisplays the status of the consumed Peer I/O input connection.87 755 DLs To Peer CfgDatalinks To Peer ConfigureSets the number of drive-to-network Datalinks (parameters) that are used forPeer I/O. The Datalinks being used are allocated from the end of the list. Forexample, if this parameter's value is set to 3, Datalinks 14…16 are allocated forthe three selected Datalinks. The Datalinks allocated for this cannot overlap withother assigned DL To Net 01…16 parameters.88 755 DLs To Peer ActDatalinks To Peer ActionDisplays the value of P87 [DLs To Peer Cfg] at the time the drive was reset. Thisis the number of actual drive-to-peer Datalinks that the drive is expecting.Default:Options:Default:Options:Default: 0Min/Max: 0 / 16Default: 0Min/Max: 0 / 160 = “Off”0 = “Off”1 = “Cmd/Ref”2 = “Custom”0 = “Off”0 = “Off”1 = “Waiting”2 = “Running”3 = “Faulted”RW 32-bitIntegerRO 32-bitIntegerRW RealRO RealPowerFlex 750-Series User Manual – Publication 750-UM001C-EN-P – September 2009