PowerFlex 750-Series AC Drives User Manual

4-16 TroubleshootingEventFault ConfigurationNo. (1) Fault/Alarm Text Type Action Paramxx081 Ch0 Msg Cheksum Configurable P9[FB0 Loss Cfg]xx082 Ch0 Timeout Configurable P9[FB0 Loss Cfg]xx083 Ch0 Comm Configurable P9[FB0 Loss Cfg]xx084 Ch0 Diagnostic Configurable P9[FB0 Loss Cfg]xx085 Ch0 SpplyVltgRng Configurable P9[FB0 Loss Cfg]xx086 Ch0 SC Amplitude Configurable P9[FB0 Loss Cfg]xx087 Ch0 Open Wire Configurable P9[FB0 Loss Cfg]xx088 Ch0 Quad Loss Configurable P9[FB0 Loss Cfg]xx089 Ch0 Phase Loss Configurable P9[FB0 Loss Cfg]xx090 Ch0 Unsupp Enc Configurable P9[FB0 Loss Cfg]xx100 Ch0 FreqExc Alm Alarm 1 P9[FB0 Loss Cfg]xx101 Ch0 TempExc Alm Alarm 1 P9[FB0 Loss Cfg]xx102 Ch0 LightLim Alm Alarm 1 P9[FB0 Loss Cfg]xx103 Ch0 Battery Alm Alarm 1 P9[FB0 Loss Cfg]xx104 Ch0 RefPoint Alm Alarm 1 P9[FB0 Loss Cfg]xx108 Ch0 General Alm Alarm 1 P9[FB0 Loss Cfg]xx115 Ch0 Optics Alarm Alarm 1 P9[FB0 Loss Cfg]xx116 Ch0 OutOfRailAlm Alarm 1 P9[FB0 Loss Cfg]xx200 Ch1 LightSrc Err Configurable P39[FB1 Loss Cfg]xx201 Ch1 SigAmp Err Configurable P39[FB1 Loss Cfg]xx202 Ch1 PsnVal Err Configurable P39[FB1 Loss Cfg]xx203 Ch1 OverVolt Err Configurable P39[FB1 Loss Cfg]xx204 Ch1 UndVolt Err Configurable P39[FB1 Loss Cfg]xx205 Ch1 OverCur Err Configurable P39[FB1 Loss Cfg]xx206 Ch1 Battery Err Configurable P39[FB1 Loss Cfg]xx209 Ch1 AnalSig Err Configurable P39[FB1 Loss Cfg]AutoResetDescriptionIndicates the option card has detected a serialcommunications checksum error while attempting tocommunicate with the encoder on channel 0.Indicates the option card has detected a serialcommunications timeout error while attempting tocommunicate with the encoder on channel 0.Indicates the option card has detected a serialcommunications error (other than checksum or timeout)while attempting to communicate with the encoder onchannel 0.Indicates the option card has detected a powerup diagnostictest failure for encoder channel 0.Indicates that the voltage source to the encoder 0 is out ofrange.Indicates that the encoder 0 signal amplitude is out oftolerance.Indicates that an open wire condition has been detected forencoder 0.Indicates that a signal quadrature error has been detectedfor encoder 0Indicates that an A or B signal of an A quad B incrementalencoder on Channel 0 is disconnected.Indicates that the connected encoder on Channel 0 is notsupportedAlarm reported by Heidenhain Encoder on Channel 0 withEnDat Interface - Frequency exceeded warningAlarm reported by Heidenhain Encoder on Channel 0 withEnDat Interface - Temperature exceeded warningAlarm reported by Heidenhain Encoder on Channel 0 withEnDat Interface - Limit of light control reserve reachedAlarm reported by Heidenhain Encoder on Channel 0 withEnDat Interface - Battery warningAlarm reported by Heidenhain Encoder on Channel 0 withEnDat Interface - Reference point not reachedAlarm reported by a Encoder on Channel 0 with BiSSInterface - A warning bit of the BiSS Single Cycle Data is setAlarm reported by a linear Stahl encoder on Channel 0 -Displays an alarm when the Stahl optical system requirescleaningAlarm reported by a linear Stahl encoder on Channel 0 -Indicates that the read encoder count is at the maximumvalue (524287)Error reported by Heidenhain Encoder on Channel 1 withEnDat Interface - Light source failureError reported by Heidenhain Encoder on Channel 1 withEnDat Interface -Signal amplitude errorError reported by Heidenhain Encoder on Channel 1 withEnDat Interface - Position value errorError reported by Heidenhain Encoder on Channel 1 withEnDat Interface - Overvoltage errorError reported by Heidenhain Encoder on Channel 1 withEnDat Interface - Undervoltage errorError reported by Heidenhain Encoder on Channel 1 withEnDat Interface - Overcurrent errorError reported by Heidenhain Encoder on Channel 1 withEnDat Interface - Battery emptyError reported by Stegmann Encoder on Channel 1 withHiperface Interface - Analog signals outside specificationPowerFlex 750-Series User Manual – Publication 750-UM001C-EN-P – September 2009