CANoe DENoe - KEMT FEI TUKE

More documents

Recommendations

Info

fixed position, cyclic update output mode Here fixed lines are assigned to the messages, as in the fixed position mode. However, the Trace window is not updated with each message any longer, but rather only cyclically with a time constant that can be configured. This saves on computing time during high bus loading, making bus observations possible on computers with weaker performance in this mode. At any time you can switch back and forth between the two representations, even during a measurement. Thus, the user can switch over to chronological output mode after the measurement to page forward and backward through the received messages in the Trace window. Note: The Trace window can be stopped by the toolbar icon during a measurement run, so that you can analyze its contents in a user-friendly manner without terminating the measurement. Furthermore, the Trace window offers you two different time formats. You can select whether the time stamp for messages should be displayed as absolute, i.e. in seconds since the start of measurement, or relative to the message preceding it. In the latter case, in fixed mode the time differences always refer to the same line. As a result, in this mode you can read off the transmission intervals between messages with the same identifiers. In Chronological mode the time differences are always shown referenced to the last message displayed in the window. If you also wish to see changes of environment variables in the Trace window, you must activate this by marking the relevant option. © Vector Informatik GmbH CANoe/DENoe Manual Version 4.1.1 97
98 3.3.2 Configuration of Columns in the Trace Window Depending on the CANoe option or purpose of the Trace window, it may be advisable to show more or fewer columns. Therefore the Trace window offers a set of possible columns that can be laid out in any desired way. Figure 58: Columns Configuration in the Trace Window A user-defined columns configuration is also possible as a standard. This means that all new Trace windows you create with this CANoe version are created with these same settings. Please refer to online Help for the exact procedure for configuring columns and selecting individual configuration sets. Note: Not all messages or events (e.g. environment variables) occurring in your system will fill the same columns or all columns. For example, the "Destination" column is not filled out for a CAN message. However, a J1939 message will show its "Destination address" in this column. © Vector Informatik GmbH CANoe/DENoe Manual Version 4.1.1
Page 1 and 2:
CANoe DENoe .CAN.LIN.MOST.FlexRay M
Page 3 and 4:
IV International Quality Standard C
Page 5 and 6:
VI Contents 1 Introduction.........
Page 7 and 8:
VIII 2.7.4.2 Configuration of Onlin
Page 9 and 10:
X 4.2.1.6 Entering Mode-Dependent S
Page 11 and 12:
XII 9.4 Synchronized timestamp ....
Page 14 and 15:
1 Introduction In this chapter, you
Page 16 and 17:
The control panels provide a user-f
Page 18 and 19:
Control box/Check box Comment box B
Page 20 and 21:
figuration dialog for the active bl
Page 22 and 23:
Make sure that you begin this tour
Page 24 and 25:
After then select + and Setup from
Page 26 and 27:
generator block, whereby the first
Page 28 and 29:
Figure 17: Transmit List for Genera
Page 30 and 31:
Figure 20: Statistics Report Beside
Page 32 and 33:
must be subtracted from the result.
Page 34 and 35:
Figure 25: Data Window With the hel
Page 36 and 37:
figuration from the data source. Yo
Page 38 and 39:
Unit 7: Create a CAPL program with
Page 40 and 41:
1.3.12 Simulation of Distributed Sy
Page 42 and 43:
In the configuration under consider
Page 44 and 45:
} msg.bsSwitch = getValue(this); //
Page 46 and 47:
The panels are generated as display
Page 48 and 49:
1.6 Particularities of the Demo Ver
Page 50 and 51:
Figure 34: CANoe during a measureme
Page 52 and 53:
Main menu line Toolbar Data window
Page 54 and 55:
The information exchange between th
Page 56 and 57:
2.2.2 Working with Configurations A
Page 58 and 59:
Figure 38: Dialog for configuring r
Page 60 and 61: Figure 40: Message and Signal Explo
Page 62 and 63: The search sequence in the database
Page 64 and 65: • The channel configuration does
Page 66 and 67: Normal Oper. Load Oper. Overload Fi
Page 68 and 69: To filter out certain messages from
Page 70 and 71: Panels to be Opened at Measurement
Page 72 and 73: Furthermore, the panel configuratio
Page 74 and 75: In the Entire Measurement trigger m
Page 76 and 77: For example, the entire measurement
Page 78 and 79: If a data loss occurs in spite of t
Page 80 and 81: Event type Format in ASCII Logging
Page 82 and 83: Nevertheless, it is often the case
Page 84 and 85: Number format: Binary A mask is ent
Page 86 and 87: 2.8 COM-Server A COM-Server is impl
Page 88 and 89: Message was not transmitted (14) Th
Page 90 and 91: Command from driver not supported (
Page 92 and 93: supplied with the card. Operation o
Page 94 and 95: The CAN controllers are provided wi
Page 96 and 97: Figure 49: Acceptance Filtering wit
Page 98 and 99: 3 Windows You can modify the arrang
Page 100 and 101: 3.1.2 Layout of the Simulation Setu
Page 102 and 103: You configure the measurement setup
Page 104 and 105: time stamp 2.7000 sec CANoe transm
Page 106 and 107: Figure 55: Simulation Dialog Note:
Page 108 and 109: WU = Wake up or TE = Transceiver er
Page 112 and 113: 3.3.3 Trace Window Options from the
Page 114 and 115: 3.4.1 Selecting Signals 101 In the
Page 116 and 117: 103 For all signals you have entere
Page 118 and 119: 105 Note: It is always the case tha
Page 120 and 121: 107 10x , n = [1 to 9], x = whole n
Page 122 and 123: 109 To optimize the Graphics window
Page 124 and 125: The popup menu command Copy content
Page 126 and 127: Display type: Decimal The raw data
Page 128 and 129: ing. However, to obtain reasonable
Page 130 and 131: Figure 67: Statistical evaluation o
Page 132 and 133: Figure 69: Bus Statistics Window 11
Page 134 and 135: If you have not entered any comment
Page 136 and 137: Figure 71: Generator block Configur
Page 138 and 139: Figure 72: Signal Response Generato
Page 140 and 141: For examples of interactive generat
Page 142 and 143: quest of the same message must foll
Page 144 and 145: 4.3 Replay Block 131 The replay blo
Page 146 and 147: 4.5 Filter block 133 The volume of
Page 148 and 149: The filter configuration is lost wh
Page 150 and 151: Note: When a CAPL node is removed f
Page 152 and 153: 139 The left side of the dialog is
Page 154 and 155: Figure 79: The Panel Editor 141 All
Page 156 and 157: 143 Note: It is now possible to aut
Page 158 and 159: 5.3.2 Configuration of the Elements
Page 160 and 161:
147 Only elements completely enclos
Page 162 and 163:
With View you can choose among thre
Page 164 and 165:
Figure 83: Configuration Dialog for
Page 166 and 167:
5.9 Panel Control 153 For complex C
Page 168 and 169:
155 Therefore, you can utilize a CA
Page 170 and 171:
Bus event: Keyboard event: Time eve
Page 172 and 173:
6.2.1 Opening Browser 159 Browser i
Page 174 and 175:
161 If you are using more than one
Page 176 and 177:
Bus Bus bus name Database Database
Page 178 and 179:
8.4 LIN Specifications CANoe.LIN su
Page 180 and 181:
9 Option .MOST In this chapter you
Page 182 and 183:
9.5 Original timestamp 169 This is
Page 184 and 185:
• Make sure, the DTD file is not
Page 186 and 187:
9.7.4.1 Lookup Key 173 The data str
Page 188 and 189:
9.8 Interactive Generator Block MOS
Page 190 and 191:
9.10 Busstatistic Window 177 The bu
Page 192 and 193:
179 mostLightLockError Most_Error E
Page 194 and 195:
9.12.5 Hardware API 9.12.5.1 Optoly
Page 196 and 197:
XOR Filter long MostSetXorFilter( )
Page 198 and 199:
9.13.3 MOST XML Catalog 185 The dem
Page 200 and 201:
9.14.8 Weird Spurious Events from M
Page 202 and 203:
10 Option .FlexRay In this chapter
Page 204 and 205:
11 Index ! ! Load symbol · 53 < k
Page 206 and 207:
Error frame · 41, 64, 95, 119, 123
Page 208 and 209:
R Radio button · 5 Raw value · 13
show all

CANoe DENoe - KEMT FEI TUKE

Create successful ePaper yourself

Delete template?

Save as template?