Introduction to the Agilent 7100 Capillary Electrophoresis System

More documents

Recommendations

Info

5 Using the Agilent 7100 Capillary Electrophoresis System Capillary Electrophoresis, CE Inserting the Cassette NOTE Use the Change Cassette task from the CE diagram to access an already installed cassette. To insert the capillary cassette into the system you have to perform the following steps. 1 Choose the cassette icon in the CE diagram and select Change Cassette… from the menu. This removes the buffer vials from the ends of the capillaries and back to their position in the tray. This will take approximately 5 seconds. 2 Open the top cover to access the cassette. 3 Press a spring located in the middle of the front lid to release the latch. Figure 34 shows the position of an installed cassette. 132 Agilent 7100 Capillary Electrophoresis System User Manual
Using the Agilent 7100 Capillary Electrophoresis System 5 Capillary Electrophoresis, CE 4 Move the cassette guide to the front. NOTE Extracting the cassette from the instrument without lowering the lifts will lead to a higher contamination of the inner parts of the electrode or pre-puncher. Crystallization or liquid residue of this contaminations might bias future runs. Cassette Cassette guide Figure 34 Insertion of cassette CAUTION Capillary damage by incorrect insertion into capillary seats The capillaries should slide directly into the capillary seats. Otherwise, they might break or be damaged. • Make sure the ends of the capillary are not bent when lowering the capillary cassette. • If you have problems inserting the capillary into the electrodes, check if they are blocked with salt crystals (see “Cleaning the Electrodes, Pre-punchers and Insulation Plate” on page 196). 5 Slowly lower the cassette until it reaches the insulation plate. While lowering the cassette, insert the capillary ends into the capillary seats of the electrodes. Agilent 7100 Capillary Electrophoresis System User Manual 133
Page 1 and 2:
Agilent 7100 Capillary Electrophore
Page 3 and 4:
In This Guide… This guide contain
Page 5 and 6:
Contents 1 Introduction 13 Introduc
Page 7 and 8:
Contents Delivery Checklist 55 Inst
Page 9 and 10:
Contents Running the CEC Analysis 1
Page 11 and 12:
Contents 9 Parts and Materials for
Page 13 and 14:
Page 15 and 16:
Introduction 1 Where to Find Inform
Page 17 and 18:
Page 19 and 20:
Site Requirements and Specification
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Installing the Instrument 3 Unpacki
Page 57 and 58:
Installing the Instrument 3 Install
Page 59 and 60:
Installing the Instrument 3 Install
Page 61 and 62:
Page 63 and 64:
LAN Configuration 4 TCP/IP Paramete
Page 65 and 66:
LAN Configuration 4 Initialization
Page 67 and 68:
LAN Configuration 4 Initialization
Page 69 and 70:
LAN Configuration 4 Link Configurat
Page 71 and 72:
LAN Configuration 4 Manual Configur
Page 73 and 74:
LAN Configuration 4 Manual Configur
Page 75 and 76:
LAN Configuration 4 Agilent Bootp S
Page 77 and 78:
Page 79 and 80:
Controlling the Agilent CE Instrume
Page 81 and 82: Using the Agilent 7100 Capillary El
Page 131: Using the Agilent 7100 Capillary El
Page 161 and 162: Agilent 7100 Capillary Electrophore
Page 163 and 164: Troubleshooting and Diagnostics 6 C
Page 169 and 170: Troubleshooting and Diagnostics 6 A
Page 171 and 172: Agilent 7100 Capillary Electrophore
Page 173 and 174: Hardware Information 7 7100 Capilla
Page 175 and 176: Hardware Information 7 7100 Capilla
Page 177 and 178: Hardware Information 7 Firmware Fir
Page 179 and 180: Hardware Information 7 Diode Array
Page 181 and 182: Hardware Information 7 Diode Array
Page 183 and 184:
Hardware Information 7 Installing D
Page 185 and 186:
Hardware Information 7 External Wat
Page 187 and 188:
Hardware Information 7 Analog to Di
Page 189 and 190:
Page 191 and 192:
Maintenance 8 Overview of Maintenan
Page 193 and 194:
Maintenance 8 Overview of Maintenan
Page 195 and 196:
Maintenance 8 Early Maintenance Fee
Page 197 and 198:
Maintenance 8 Cleaning the Electrod
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Maintenance 8 Maintenance of the Re
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Maintenance 8 Changing the Air Inle
Page 225 and 226:
Maintenance 8 Changing the Lamp Rem
Page 227 and 228:
Maintenance 8 Changing the Lamp Ins
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Appendix 10 General Safety Informat
Page 235 and 236:
Appendix 10 Allgemeine Sicherheitsi
Page 237 and 238:
Appendix 10 Allgemeine Sicherheitsi
Page 239 and 240:
Appendix 10 Informations générale
Page 241 and 242:
Appendix 10 Informazioni generali s
Page 243 and 244:
Appendix 10 Informazioni generali s
Page 245 and 246:
Appendix 10 Información de segurid
Page 247 and 248:
Appendix 10 安全に関する
Page 249 and 250:
Appendix 10 安全に関する
Page 251 and 252:
Appendix 10 一般安全信息
Page 253 and 254:
Appendix 10 Setting Up a Test Sampl
Page 255 and 256:
Appendix 10 Setting Up a Test Sampl
Page 257 and 258:
Appendix 10 The Waste Electrical an
Page 259 and 260:
Appendix 10 Sound Emission Sound Em
Page 261 and 262:
Appendix 10 Agilent Technologies on
Page 263 and 264:
Index A accessing 199 accessories 5
Page 266:
www.agilent.com In This Book This m
show all

Introduction to the Agilent 7100 Capillary Electrophoresis System

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?